Miele G 7883 CD Electrical connection, This Appliance Must Be Grounded, Grounding connection

Page 68
Electrical connection

Electrical connection

,All electrical work must be carried out by a suitably qualified electrician in accordance with local and national safety regulations.

Connection should be made via a suitable isolator, with an on-off switch that is easily accessible for servicing work.

The electrical connection is made through a receptacle according to national requirements. The receptacle has to be easily accessible after installation.

To increase the security it is recommended to install a protective switch (30 mA) before the machine.

For technical data see the data plate or wiring diagram supplied.

The machine must only be operated with the voltage, frequency and fusing shown on the data plate.

The machine can be converted according to the supplied converting diagram and wiring diagram.

The data plate is located at the rear of the machine and behind the plinth on the plastic cover.

The wiring diagram is supplied with the machine.

See also the supplied installation diagram.

A damaged power cord must only be replaced with a genuine Miele cord by a Miele service technician.

WARNING

THIS APPLIANCE MUST BE GROUNDED

Grounding connection

^The ground lead must be connected to the screw connection point (marked with the ground symbol 8) at the back of the machine.

The machine must only be operated with the voltage, frequency and fusing shown on the data plate located on the rear of the machine, and on the plinth (behind the service panel).

The conversion diagram and the wiring diagram is secured to the inner side of the service panel.

68

Image 68
Contents en - US, CA Operating and Installation InstructionsLaboratory Glassware Washer G 7883 CD Page Contents Program Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Programming functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 The following instructions apply to all programming functions:. . . . . . . . . . . . . . . 36 To access the programming mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Saving to memory and exiting the programming mode . . . . . . . . . . . . . . . . . . 36 Exiting the programming mode without saving . . . . . . . . . . . . . . . . . . . . . . . . 36 DOS 1 liquid detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Setting the detergent dosage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Priming the dosage system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 DOS 3 neutralizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Setting the neutralizer dosage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Priming the dosage system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Buzzer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Changing program parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Changing the temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Changing the holding time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Restoring the factory settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Setting the time and date. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Resetting the coarse and fine filter timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Data transfer optional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Routine checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Frequently asked questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Thermo switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 After Sales Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 INSTALLATION INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Plumbing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IMPORTANT SAFETY INSTRUCTIONS ~Take care when handling processing chemicals detergents, softeners, neutralizers, etc.. These may contain irritant or corrosive ingredients. Do not use organic solvents as these could cause an explosion. Wear protective gloves and goggles. With all chemical agents the manufacturer’s safety conditions must be observed IMPORTANT SAFETY INSTRUCTIONS Please note the following symbols on the machine AccessoriesSAVE THESE INSTRUCTIONS Disposal of an old applianceGuide to the lab washer h Service panel i Serial interface a Drying unitc Dispenser for powdered detergent d Rinse aid reservoir with dosage selectorIntended applications: Laboratory equipment Description of the machineStandard model Opening and closing the door Electric door lockTo open the door To close the doorSetting the water softener Water softenerSettings factory settingFilling the salt reservoir Salt indicator Rinse Aid Adding rinse aidRinse aid indicator light Setting the rinse aid dosageNeutralizing agent Adding neutralizerNeutralizer indicator light Adding detergent Setting the liquid detergent dosageDetergent Liquid detergent refill light ^Load the detergent into the compartment ^Snap the cover closedLoading the machine Special preparations before operating the machine Loading the machinePrepare items before loading To adjust the upper basket Adjusting the upper basketSpring adapter for the water connection Laboratory equipment Lower basket U Upper basket OFor various inserts E Injector wagon O Injector wagonFor narrow necked glassware Upper basket For direct injection ofSelecting the optional drying function Turning onStarting a program Program sequence display Additional drying End of a programTurning off Canceling a program Program Guide Program sequence Programming functions To access the programming modeGeneral information Saving to memory and exiting the programming modeDOS 1 liquid detergent Setting the detergent dosageStep Display / ResultDOS 3 neutralizer Setting the neutralizer dosageBuzzer Changing the drying parameters Changing program parametersChanging the wash and rinse parameters Changing the temperature Step Changing the holding time StepRestoring the factory settings Setting the time and date Resetting the coarse and fine filter timer Data transfer optional Maintenance Routine checksCleaning and Care Cleaning the filters in the wash cabinetCleaning the fine, flat and micro-finefilters Cleaning the spray arms Removing the spray armsCleaning the drain pump and non-returnvalve Cleaning the water inlet filters Cleaning the filtersCleaning the control panel Cleaning the exteriorCleaning the wash cabinet Cleaning the door sealBaskets and inserts Frequently asked questions Possible faultSolution What ifFrequently asked questions What ifFrequently asked questions What ifFrequently asked questions What ifFrequently asked questions What ifFrequently asked questions Items made of glass show signs ofcorrosion Items made of stainlesson the labware There are whitedeposits and/or spots The wash result is unacceptableThermo switch U1-800-991-9380techserv@mieleusa.com After Sales ServiceV1-800-565-6435service@miele.ca INSTALLATION INSTRUCTIONS Positioning and securing the machine InstallationLeveling the legs Cover plate protects the countertop Removing the lid if necessaryProtecting the countertop Grounding connection Electrical connectionTHIS APPLIANCE MUST BE GROUNDED Connecting the water inlet PlumbingPlease also refer to the installation diagram DI Connection pressurized DI connection unpressurized optionalDrainage Metric Technical dataEnglish Disposal of an old appliance Caring for the environmentDisposal of the packing materials Page Subject to change without notice / M.-Nr.07 157 440 /