Sterling SLC 5/04, 100, 600, 015, 060 specifications Manual Backup Control System

Page 48

The blender will blend at a maximum rate when the lower mass flow weigh hopper has a very low weight of material. As the weight of material increases in the mass flow weigh hopper, the controller will adjust the blender feeders output to match the calculated processing machine rate. The blender will adjust in so that it is running a very closely matched rate to the extruder and readjust the ingredient hopper outputs accordingly.

The processing rate and the blending rate displayed on the blender control will not match exactly for any extended period of time as the dynamics of the extrusion process produces a continuously changing rate for the extruder. The blender will follow this dynamic changing rate very closely. The learned processing rate is accurate enough for mono-layer extrusion yield control or co-extrusion layer thickness control.

If the extruder is slowed or stopped suddenly, the blender will reach the high weight point in the lower mass flow hopper, slow down, and stop the metering devices so the weigh hopper will not overfill.

Manual Backup Control System

Every continuous blender is equipped with a secondary manual backup control system. This allows the blender to be switched over to manual operation. In this mode, the feeder speeds are adjusted manually, and the blender will run, blending volumetrically. The lower mass flow weigh hopper is equipped with a proximity sensor mounted on the upper level of the hopper. This is for the manual operation to cycle the metering augers if the level of material in the weigh hopper reaches a high level.

This secondary control will allow the blender to be operated to provide production in the event of a control failure. After correction, the blender can be switched back into automatic operation.

When the blender is running in steady automatic mode, simply check the motor voltages (or) frequency readouts and record them. Then the drives can simply be “dialed in” for emergency volumetric operation.

Continuous Loss-in-Weight Blenders

Chapter 4: Operation

48

Page 47 Page 49
Image 48
Page 47 Page 49
Contents Continuous Loss-in-Weight Blenders Shipping Information Warranty Returns Credit ReturnsTable of Contents Maintenance Safety How to Use This ManualSafety Symbols Used in this Manual Continuous Loss-in-Weight Blender Safety Tags Description Follow all Safety Codes Wear Safety Glasses and Work GlovesResponsibility General ResponsibilityOperator Responsibility RememberMaintenance Responsibility Reporting a Safety DefectAccessories Customer ServiceFunctional Description Models Covered in This ManualTypical Features & Components Mechanical FeaturesController Features Electrical FeaturesBlender System Component Description Ingredient Weigh Hoppers Ingredient Metering/Transport Auger Assemblies Metering Auger Components Cascade Material ChuteLower Mass Flow Weigh Hopper Assembly Weigh Hopper Assembly Fixed Rate modePLC Control Panel Touch Screen InterfaceMotor Drive Panel Optional Quick Color Change KitOptions Mezzanine stand with slide gate and 4 tube stubRemote Display Safety Devices and Interlocks Safety Circuit StandardsFail Safe Operation Safety Device Lock-Outs Pluggable Line CordAmphenol quick connect Plug Connected to Each Auger Motor Installation Uncrating the EquipmentRigging and Placing the Unit Mounting Configuration Site RequirementsMachine Mount Mezzanine Mount Offset Mezzanine Mount PositionFloor Mount Electrical Installation Typical Layout for a floor mounted blenderPneumatic Installation Pneumatic Air SystemOverall Installation Summary Load Cell Adjustment Set-upFinal Connections Controller Setup Scale CalibrationBlender Calibration Weight Scale Calibration Page Feeder Calibration Touch the Calibration button Setting Hopper Size Capacity @35 lbs. / cu. ftTouch Hopper Setup Setting PasswordsService Touch User Password Alarm Setup Touch Alarm Setup Page Setting Blender for English or Metric How to use Fifo Diagnostics Continuous Loss-in-Weight Blenders Installation Page Operation Start-upGeneral Operation Manual Backup Control System Controller Description & Operation Display DescriptionContinuous Loss-in-Weight Blenders Operation Setting a Recipe Clean OutMaintenance Preventative Maintenance ScheduleContinuous Loss-in-Weight Blenders Chapter Maintenance Typical Blender Parts List Typical Weigh Hopper Assembly Parts ListChapter Appendix Spare PartsAnnex B Information Addendum Service Supervisor Information PasswordsProgrammable Settings Advanced Hopper Options Feed Factor Filter Steady Feed FactorMax WTP/RPM Re-fill PercentagePID Timer Steady System LimitSteady System Time Test PID GainPID Integral Constant Feeder Speed LimitsExtruder RPM Options Update Time for Prox Method in seconds Extrusion Control Options Feeder SetupAllowed Extruder RPM Change for Steady Flag Advanced Alarm Options No Flow TimerNo Flow Bits Service Department Technical AssistanceParts Department Sales Department

060, SLC 5/04, 015, 600, 100 specifications

Sterling 100,600,015 SLC 5/04,060 is a robust and versatile industrial automation controller designed to meet the demands of various industrial applications. As part of the Sterling lineup, this model is particularly known for its reliability and advanced features that enhance operational efficiency.

One of the main features of the Sterling 100,600,015 SLC 5/04,060 is its modular architecture, which allows users to customize the system based on their specific needs. The controller supports a wide range of I/O modules, providing flexibility in expanding or modifying the system as production requirements change. This modularity ensures scalability, making it suitable for both small-scale and large-scale applications.

The controller operates on the well-established Allen-Bradley SLC 500 platform, which is known for its stability and ease of use. With a processing speed of 100 kHz, the SLC 5/04,060 can handle multiple tasks simultaneously, ensuring precise control over processes. This speed is complemented by a large memory capacity, allowing for complex programming and data storage without compromising performance.

In terms of communication, the Sterling 100,600,015 SLC 5/04,060 features multiple communication ports, including RS-232 and RS-485 interfaces, making it compatible with various devices and systems. This capability enables seamless integration with existing networks, as well as the implementation of modern network protocols like Ethernet for greater connectivity and data transfer efficiency.

The controller is also equipped with advanced diagnostics capabilities, enabling users to monitor system performance in real-time. This feature not only helps in quick troubleshooting but also aids in predictive maintenance strategies, reducing downtime and optimizing productivity.

In addition to its hardware features, the Sterling 100,600,015 SLC 5/04,060 supports a range of programming languages, including ladder logic, structured text, and function block diagrams. This versatility allows engineers and technicians to choose the most suitable approach for their specific projects, making the development process more intuitive and efficient.

Overall, the Sterling 100,600,015 SLC 5/04,060 is a powerful and adaptable solution for industrial automation, combining advanced technology with ease of use, making it an ideal choice for businesses seeking to enhance their operational capabilities and efficiency.
Top Page Image Contents