GE PSB1200BB, ZSC1201SS 30″23-1/2″, 21 ″, 30″ 21″ 36-3/4″ Min 23-1/2″ 25-1/4″ Construct Solid

Page 9

Installation Preparation

Preparation WITH an Accessory Storage Drawer

NOTE: MODEL ZSC1201 CAN ONLY BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER IF INSTALLED ABOVE 36-3/4.

MODEL ZSC1202 CANNOT BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER. SEE INSTALLATION PREPARATION WITHOUT AN ACCESSORY STORAGE DRAWER FOR THIS MODEL.

PREPARE THE OPENING (cont.)

The Advantium 120V can be installed in combination with other GE/Monogram appliances. Always follow each product’s Installation

PREPARE THE OPENING (cont.)

Installation over a GE/Monogram Warming Drawer:

Instructions to complete the installation.

Single Advantium 120V Installation:

Order a 30wide single oven cabinet or cut the opening in a wall to the dimensions shown.

3023-1/2

 

 

 

 

 

 

 

25-1/4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Min.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

21

 

 

 

 

Construct Base

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

36-

 

3/4

 

 

 

Min. 3/8Plywood

 

 

 

 

Supported by 2 x 4

30

21

36-3/4

Min.*

23-1/2

25-1/4

Min.

Construct Solid

Bottom Min. 3/8Plywood Supported by 2 x 4 or 2 x 2 Runners all Four Sides

2Min.

(3Recommended)

Per Warming

Drawer

Requirement

*Required for Monogram models

Min.*

or 2 x 2 Runners

 

 

all Four Sides

 

 

 

 

*Required for

 

 

Monogram models

 

 

 

Allow 2-1/8case trim overlap on the sides,

1-1/16overlap on the top and 7/8overlap on the bottom of the opening for all models.

Oven overlaps will conceal cut edges on all sides of the opening.

When installed over a single oven or a warming drawer, allow at least 2between the two openings. This separation will provide clearance for bottom overlap of the Advantium 120V and the other appliance overlaps.

Construct a solid oven floor of 3/8min. thick plywood supported by 2 x 4 or 2 x 2 runners on all sides.

The support must be level and rigidly mounted, flush with the bottom edge of the cutout .

NOTE: Additional clearances between the cutouts may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior depth

and height . See Warming Drawer installation instructions for details.

9

Image 9
Contents Installation Instructions Models Available ContentsParts Supplied Safety glasses or gogglesAdvance Planning 8 ″Single Advantium 120 Installation Electrical RequirementsElectrical Location Prepare the Opening Single Advantium 120V InstallationInstallation over a GE/Monogram Oven and Warming Drawer Installation over a GE/Monogram oven30″ 23-1/2″ Drawer17-1/2″ 25-1/4″ ″ Min2″Min 2″Recommended 21 ″ 30″23-1/2″30″ 21″ 36-3/4″ Min 23-1/2″ 25-1/4″ Construct Solid All Four SidesWarming Drawer 21″ 25-1/4″ Cooktop Installation Instructions Discard plastic trim. Replace screws Slide the Oven Into the CutoutInstall Bottom Trim Install Mounting ScrewsFinalize Installation Allow 15″ clearance When fully open ZX2201SS-Stainless Steel for installation above 36″ onlyTools Required JX2200BB-Black JX2201SS-Stainless SteelAssembling the Oven to Drawer Remove Packaging and PartsAssembling the Oven to Drawer Page GE Consumer & Industrial