GE C2S980 Instructions, Cook and Hold, Safety Gas/Control Lockout on some models

Page 25

ge.com

Safety

Gas/Control Lockout (on some models)

Your control will allow you to lock out the surface burners, oven burners and control panel so they cannot be activated.

To lock/unlock the controls:

Turn all surface burners off.

Touch and hold the GAS/CONTROL LOCKOUT pad for 3 seconds until the display shows LOC.

To unlock the control, touch and hold the GAS/CONTROL LOCKOUT pad for 3 seconds until LOC disappears from the display.

When this feature is on and the touch pads are touched, the control will beep and the display will show LOC.

The control lock-out mode affects all controls. No controls will work when this feature is activated.

The adjustment will be retained in memory after a power failure.

Instructions Operating

12 Hour, 24 Hour or Clock Black-Out

Your control is set to use a 12 hour clock.

If you would prefer to have a 24 hour military time clock or black-out the clock display, follow the steps below.

Touch the BAKE and BROIL HI/LO pads at the same time for 3 seconds until the display shows SF.

Touch the CLOCK pad once. The display will show 12 hr. If this is the choice you want, touch the START pad.

Touch the CLOCK pad again to change

to the 24 hour military time clock. The display will show 24 hr. If this is the choice you want, touch the START pad.

Touch the CLOCK pad again to black-out the clock display. The display will show OFF. If this is the choice you want, touch the START pad.

NOTE: If the clock is in the black-out mode you will not be able to use the Delay Start function.

Instructions

Instructions

Installation

Cook and Hold

Your new control has a cook and hold feature that keeps cooked foods warm for up to 3 hours after the cooking function is finished.

This feature can only be used when timed cooking.

To activate this feature, follow the steps below.

Touch the BAKE and BROIL HI/LO pads at the same time for 3 seconds until the display shows SF.

Touch the COOKING TIME pad. The display will show Hld OFF.

Touch the COOKING TIME pad again to activate the feature. The display will show Hld ON.

Touch the START pad to activate the cook and hold feature and leave the control set in this special features mode.

Troubleshooting Tips Consumer Support

25

Image 25
Contents Troubleshooting Tips Safety InstructionsWrite the model and serial numbers here Model # Serial # ANTI-TIP Device Operating Instructions Safety Instructions InstallationAll ranges can tip and injury could result Troubleshooting Tips Consumer SupportGe.com Installation Instructions Operating Instructions Safety InstructionsConsumer Support Safety Operating Instructions Safety InstructionsLower Oven Drawer Operating Installation Instructions Instructions Safety InstructionsSupport Troubleshooting TipsSafety Using the gas surface burnersInstructions Installation SupportSafety Instructions Using the griddleHow to Insert the Griddle Using the GriddleCase of Power Failure Troubleshooting TipsTop-of-Range Cookware Stove Top GrillsOperating Instructions Safety Instructions Using the upper oven controlsConsumer Support Troubleshooting Tips Instructions Operating Using the upper ovenBefore you begin… Upper Oven VentPreheating and Pan Placement How to Set the Upper Oven for Baking or RoastingOperating Aluminum FoilBroiling Guide How to Set the Upper Oven for Broiling-Close the oven doorHI Broil Broil HI/LO pad againInstructions Safety Using the clock and timerInstallation Instructions Tips How to Set an Immediate Start and Automatic Stop Using the timed baking Roasting features upper oven onlyHow to Set a Delayed Start and Automatic Stop Operating InstructionsHow to Set the Upper Oven For Roasting When Using the Probe Using the probeInsert the probe into the food Convection Bake Using the convection ovenConvection Roast Auto Recipe ConversionMulti-Shelf Baking Installation Instructions Troubleshooting TipsCookware for Convection Cooking Paper and PlasticTouch the Convection Roast pad Convection Roasting Guide Make sure the clock shows the correct time of day Using the timed convection Baking features upper oven onlyFahrenheit or Celsius Temperature Selection Special features of your upper oven controlHour Shut-Off Tones at the End of a Timed CycleInstructions Safety Gas/Control Lockout on some modelsCook and Hold Hour, 24 Hour or Clock Black-OutHow to Set for Regular Baking/Roasting Using the Sabbath Feature. on some modelsHow to Exit the Sabbath Feature To Adjust the Thermostat Adjust the upper oven thermostat-Do it yourselfType of margarine will affect baking performance Adjust the oven thermostat-Do it yourself Using the lower oven drawerOperating Instructions Safety To Use the Lower Oven DrawerBefore a Clean Cycle Using the self-cleaning upper ovenHow to Set the Upper Oven for Cleaning Instructions Operating InstructionsHow to Delay the Start of Cleaning After a Clean CycleTo start Touch the Start pad Sealed Burner Assemblies Care and cleaning of the rangeTurn all controls OFF before removing the burner parts Burner Caps and Heads Burner Grates Tips Consumer SupportCooktop Surface Griddle Griddle PrecautionsStainless Steel Surfaces on some models Griddle is to be used over the center burner onlyTo clean the outside of the door To clean the inside of the doorLift-Off Oven Door Oven Heating ElementsGlass Window Removable Lower Oven DrawerTo remove the drawer To replace the drawer Slide the drawer all the wayUpper Control Panel Oven Air VentsLower Control Panel and Knobs Oven Shelves and Drawer Racks Oven Light ReplacementTo remove Do not remove any screws to remove the coverSafety Instructions Operating Instructions Installation of the rangeInstructions Installation If you smell gasOperating Instructions Installation InstructionsDimensions and Clearances Gas line shut-off valve Operating Instructions SafetyTroubleshooting Tips Consumer Support Recommended Gas Pipe Outlet Locations Safety InstructionsOperating Gas Supply RequirementsProvide Proper Electrical Supply Electrical Power Supply RequirementsRecommended Electrical Outlet Locations Locate the electric supply as illustratedConnect the Range to the Gas Supply Flexible Connector Hookup Rigid Pipe Hookup OptionsTeflon Registered trademark of DuPont Replace the Power Cord Optional Using an Existing Nema 14-50R ReceptacleRemove the wire cover on the back Do not discard these screwsInsert the new power cord through the strain Wire Power Cord Installation OptionWire Conduit Installation Option Replace the Wire Cover Wire Conduit Installation Option Safety InstructionsTips Consumer Seal the Openings Oval Center Burner Head/Cap AssemblyAssemble Surface Burners CapsCheck Ignition of Surface Burners Safety Instructions OperatingQuality of Flames Level the RangeInstall the Anti-Tip Device Instructions SafetyWhen All Hookups Are Completed Must be performed by a qualified LP gas installerTroubleshooting Tips Consumer Support Before you call for service…Problem Possible Causes What To Do Self-clean Clock and timerAfter a clean cycle Is setSafety Instructions Operating Instructions Installation Fully extend the drawer and push it all the way Wait for the self-clean cycle to finish and the ovenTo cool Controls improperly set See the Lower oven drawer sectionLooking For Something More? AccessoriesConsumer Support GE Service Protection Plus We’ll Cover Any Appliance. Anywhere AnytimeConsumer Product Ownership Registration What GE Will Not Cover GE Will ReplaceWarrantor General Electric Company. Louisville, KY One YearInstructions Safety Instructions GE Dual Fuel Range Warranty. For customers in CanadaMabe Will Replace What Mabe Will Not CoverInstallation Instructions GE Appliances Website Consumer Support
Related manuals
Manual 64 pages 46.44 Kb

C2S980 specifications

The GE C2S980,04-09 JR,49-85167-1,183D5580P249 is a sophisticated control system utilized in various industrial applications, specifically designed for enhancing efficiency and reliability. This model exemplifies advanced technologies and systems integration, catering to the needs of modern industries.

One of the main features of the GE C2S980 is its flexibility, allowing it to be integrated seamlessly into different types of systems. This adaptability makes it suitable for manufacturing plants, power generation facilities, and other industrial environments. The device is engineered for mobility and can be quickly deployed or modified according to the operational requirements of the facility.

A notable technology embedded within the GE C2S980 is its robust data acquisition capabilities. It can gather and process large volumes of data in real-time, which is crucial for effective monitoring and control. This feature enables operators to make informed decisions based on accurate and up-to-date information regarding equipment performance and system health.

Additionally, the GE C2S980 is equipped with advanced diagnostic tools. These tools assist in identifying faults and inefficiencies within the system, thereby reducing maintenance costs and minimizing downtime. Its built-in analytics engine helps in predictive maintenance, enabling industries to foresee potential issues before they escalate into serious problems.

The C2S980 also prioritizes user experience, featuring an intuitive interface that simplifies the navigation of complex controls. This user-friendly design reduces the learning curve for operators, enhancing overall productivity.

Another critical characteristic is its compliance with industry standards, ensuring safety and reliability in various applications. The system is designed to operate in challenging conditions and is built to withstand environmental factors, thus guaranteeing longevity and consistent performance.

In terms of connectivity, the GE C2S980 supports various protocols, facilitating interoperability with other devices and systems. This connectivity is essential for industries that rely on integrating multiple technologies into their operations.

Overall, the GE C2S980,04-09 JR,49-85167-1,183D5580P249 stands out due to its combination of advanced technology, user-centric design, and adaptability to diverse industrial environments, making it an invaluable asset for enhancing operational efficiencies.