GE C2S980 Safety Instructions Operating, Check Ignition of Surface Burners, Quality of Flames

Page 51

Read these instructions completely and carefully.

Check Ignition of Surface Burners

Operation of all cooktop burners should be checked after the range and gas supply lines have been carefully checked for leaks.

Electric Ignition

Select a top burner knob and simultaneously push in and turn to LITE position. You will hear

a clicking sound indicating proper operation of the spark module. Once the air has been purged from the supply lines, burners should light within

4 seconds. After burner lights, rotate knob out

of the LITE position. Try each burner in succession until all burners have been checked.

Safety Instructions Operating

Quality of Flames

The combustion quality of burner flames needs to be determined visually.

(A) Yellow flames—

Call for service

(B) Yellow tips on outer cones— Normal for LP gas

(C) Soft blue flames—Normal for natural gas

If burner flames look like (A), call for service. Normal burner flames should look like (B) or (C), depending on the type of gas you use.

With LP gas, some yellow tipping on outer cones is normal.

Instructions

Instructions

Installation

 

 

Troubleshooting

Level the Range

Install the oven shelves in the oven and position the range where it will be installed.

Lower

Raise

Lower

range

range

range

 

 

 

Leg leveler

Raise range

(on some models)

(on some models)

Check for levelness by placing a spirit level or a cup, partially filled with water, on one of the oven shelves. If using a spirit level, take two readings—with the level placed diagonally first in one direction and then the other.

Remove the lower oven drawer. See the Care and cleaning of the range section. The front leveling legs can be adjusted from the bottom and the rear legs can be adjusted from the top or the bottom.

Use an open-end or adjustable wrench to adjust the leveling legs until the range is level.

After the range is level, slide the range away from the wall so that the Anti-Tip device can be installed.

51

Tips Consumer Support

Page 50 Page 52
Image 51
Page 50 Page 52
Contents Safety Instructions Troubleshooting TipsWrite the model and serial numbers here Model # Serial # ANTI-TIP Device Operating Instructions Safety Instructions InstallationTroubleshooting Tips Consumer Support All ranges can tip and injury could resultGe.com Operating Instructions Safety Instructions Installation InstructionsConsumer Support Safety Operating Instructions Safety InstructionsLower Oven Drawer Tips Instructions Safety InstructionsOperating Installation Instructions Support TroubleshootingSupport Using the gas surface burnersSafety Instructions InstallationUsing the Griddle Using the griddleSafety Instructions How to Insert the GriddleStove Top Grills Troubleshooting TipsCase of Power Failure Top-of-Range CookwareUsing the upper oven controls Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips Upper Oven Vent Using the upper ovenInstructions Operating Before you begin…Aluminum Foil How to Set the Upper Oven for Baking or RoastingPreheating and Pan Placement OperatingBroil HI/LO pad again How to Set the Upper Oven for Broiling-Close the oven doorBroiling Guide HI BroilUsing the clock and timer Instructions SafetyInstallation Instructions Tips Operating Instructions Using the timed baking Roasting features upper oven onlyHow to Set an Immediate Start and Automatic Stop How to Set a Delayed Start and Automatic StopUsing the probe How to Set the Upper Oven For Roasting When Using the ProbeInsert the probe into the food Auto Recipe Conversion Using the convection ovenConvection Bake Convection RoastPaper and Plastic Installation Instructions Troubleshooting TipsMulti-Shelf Baking Cookware for Convection CookingTouch the Convection Roast pad Convection Roasting Guide Make sure the clock shows the correct time of day Using the timed convection Baking features upper oven onlyTones at the End of a Timed Cycle Special features of your upper oven controlFahrenheit or Celsius Temperature Selection Hour Shut-OffHour, 24 Hour or Clock Black-Out Safety Gas/Control Lockout on some modelsInstructions Cook and HoldUsing the Sabbath Feature. on some models How to Set for Regular Baking/RoastingHow to Exit the Sabbath Feature Adjust the upper oven thermostat-Do it yourself To Adjust the ThermostatType of margarine will affect baking performance To Use the Lower Oven Drawer Using the lower oven drawerAdjust the oven thermostat-Do it yourself Operating Instructions SafetyInstructions Operating Instructions Using the self-cleaning upper ovenBefore a Clean Cycle How to Set the Upper Oven for CleaningAfter a Clean Cycle How to Delay the Start of CleaningTo start Touch the Start pad Care and cleaning of the range Sealed Burner AssembliesTurn all controls OFF before removing the burner parts Burner Caps and Heads Tips Consumer Support Burner GratesCooktop Surface Griddle is to be used over the center burner only Griddle PrecautionsGriddle Stainless Steel Surfaces on some modelsOven Heating Elements To clean the inside of the doorTo clean the outside of the door Lift-Off Oven DoorSlide the drawer all the way Removable Lower Oven DrawerGlass Window To remove the drawer To replace the drawerOven Air Vents Upper Control PanelLower Control Panel and Knobs Do not remove any screws to remove the cover Oven Light ReplacementOven Shelves and Drawer Racks To removeIf you smell gas Installation of the rangeSafety Instructions Operating Instructions Instructions InstallationOperating Instructions Installation InstructionsDimensions and Clearances Gas line shut-off valve Operating Instructions SafetyGas Supply Requirements Recommended Gas Pipe Outlet Locations Safety InstructionsTroubleshooting Tips Consumer Support OperatingLocate the electric supply as illustrated Electrical Power Supply RequirementsProvide Proper Electrical Supply Recommended Electrical Outlet LocationsFlexible Connector Hookup Rigid Pipe Hookup Options Connect the Range to the Gas SupplyTeflon Registered trademark of DuPont Do not discard these screws Using an Existing Nema 14-50R ReceptacleReplace the Power Cord Optional Remove the wire cover on the backInsert the new power cord through the strain Wire Power Cord Installation OptionWire Conduit Installation Option Wire Conduit Installation Option Safety Instructions Replace the Wire CoverTips Consumer Caps Oval Center Burner Head/Cap AssemblySeal the Openings Assemble Surface BurnersLevel the Range Safety Instructions OperatingCheck Ignition of Surface Burners Quality of FlamesMust be performed by a qualified LP gas installer Instructions SafetyInstall the Anti-Tip Device When All Hookups Are CompletedBefore you call for service… Troubleshooting Tips Consumer SupportProblem Possible Causes What To Do Is set Clock and timerSelf-clean After a clean cycleSafety Instructions Operating Instructions Installation Controls improperly set See the Lower oven drawer section Wait for the self-clean cycle to finish and the ovenFully extend the drawer and push it all the way To coolLooking For Something More? AccessoriesConsumer Support GE Service Protection Plus We’ll Cover Any Appliance. Anywhere AnytimeConsumer Product Ownership Registration One Year GE Will ReplaceWhat GE Will Not Cover Warrantor General Electric Company. Louisville, KYWhat Mabe Will Not Cover GE Dual Fuel Range Warranty. For customers in CanadaInstructions Safety Instructions Mabe Will ReplaceInstallation Instructions GE Appliances Website Consumer Support
Related manuals
Manual 64 pages 46.44 Kb

C2S980 specifications

The GE C2S980,04-09 JR,49-85167-1,183D5580P249 is a sophisticated control system utilized in various industrial applications, specifically designed for enhancing efficiency and reliability. This model exemplifies advanced technologies and systems integration, catering to the needs of modern industries.

One of the main features of the GE C2S980 is its flexibility, allowing it to be integrated seamlessly into different types of systems. This adaptability makes it suitable for manufacturing plants, power generation facilities, and other industrial environments. The device is engineered for mobility and can be quickly deployed or modified according to the operational requirements of the facility.

A notable technology embedded within the GE C2S980 is its robust data acquisition capabilities. It can gather and process large volumes of data in real-time, which is crucial for effective monitoring and control. This feature enables operators to make informed decisions based on accurate and up-to-date information regarding equipment performance and system health.

Additionally, the GE C2S980 is equipped with advanced diagnostic tools. These tools assist in identifying faults and inefficiencies within the system, thereby reducing maintenance costs and minimizing downtime. Its built-in analytics engine helps in predictive maintenance, enabling industries to foresee potential issues before they escalate into serious problems.

The C2S980 also prioritizes user experience, featuring an intuitive interface that simplifies the navigation of complex controls. This user-friendly design reduces the learning curve for operators, enhancing overall productivity.

Another critical characteristic is its compliance with industry standards, ensuring safety and reliability in various applications. The system is designed to operate in challenging conditions and is built to withstand environmental factors, thus guaranteeing longevity and consistent performance.

In terms of connectivity, the GE C2S980 supports various protocols, facilitating interoperability with other devices and systems. This connectivity is essential for industries that rely on integrating multiple technologies into their operations.

Overall, the GE C2S980,04-09 JR,49-85167-1,183D5580P249 stands out due to its combination of advanced technology, user-centric design, and adaptability to diverse industrial environments, making it an invaluable asset for enhancing operational efficiencies.
Top Page Image Contents