GE C2S980 Installation of the range, Safety Instructions Operating Instructions, If you smell gas

Page 39

Installation of the range.

Read these instructions completely and carefully.

IN THE COMMONWEALTH OF MASSACHUSETTS

■This product must be installed by a licensed plumber or gas fitter.

■When using ball type gas shut-off valves, they shall be the T-handle type.

■A flexible gas connector, when used, must not exceed 3 feet.

BEFORE YOU BEGIN

Installation of this range must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA.54, latest edition. In Canada, installation must conform with the current Natural Gas Installation Code, AN/CGA-B149.1 or the current Propane Installation Code, CAN/CGA-B149.2, and with local codes where applicable. This range has been design-certified by CSA International according to ANSI Z21.1, latest edition and Canadian Gas Association according to CAN/CGA-1.1 latest edition.

Safety Instructions Operating Instructions

As with any appliance using gas and generating heat, there are certain safety precautions you should follow. You will find these precautions in the Important Safety Information section in the front of this manual. Read them carefully.

IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES.

NOTE: This appliance must be properly grounded.

IMPORTANT: Save these instructions for the local electrical inspector’s use.

NOTE TO INSTALLER: Leave these instructions with the appliance after installation is completed.

NOTE TO CONSUMER: Keep this Owner’s Manual and Installation Instructions for future use.

SERVICER: The electrical diagram is in an envelope attached to the back of the range.

Instructions

Installation

FOR YOUR SAFETY

Do not store or use combustible materials, gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

Troubleshooting

If you smell gas:

Open windows.

Don’t touch electrical switches.

ELECTRICAL REQUIREMENTS

Extinguish any open flame.

Immediately call your gas supplier.

Tips

CAUTION: FOR PERSONAL SAFETY, DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE. REMOVE HOUSE FUSE OR OPEN CIRCUIT BREAKER BEFORE BEGINNING INSTALLATION.

This appliance must be supplied with the proper voltage and frequency, and connected to an individual, properly grounded circuit, protected by a circuit breaker or time-delay fuse, as noted on the rating plate.

Wiring must conform to National Electric Codes.

If the electric service provided does not meet the above specifications, have a licensed electrician install an approved outlet.

Because range terminals are not accessible after range is in position, flexible service conduit or cord must be used.

39

Consumer Support

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Safety Instructions Troubleshooting TipsWrite the model and serial numbers here Model # Serial # ANTI-TIP Device Operating Instructions Safety Instructions InstallationTroubleshooting Tips Consumer Support All ranges can tip and injury could resultGe.com Operating Instructions Safety Instructions Installation InstructionsConsumer Support Safety Operating Instructions Safety InstructionsLower Oven Drawer Tips Instructions Safety InstructionsOperating Installation Instructions Support TroubleshootingSupport Using the gas surface burnersSafety Instructions InstallationUsing the Griddle Using the griddleSafety Instructions How to Insert the GriddleStove Top Grills Troubleshooting TipsCase of Power Failure Top-of-Range CookwareUsing the upper oven controls Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips Upper Oven Vent Using the upper ovenInstructions Operating Before you begin…Aluminum Foil How to Set the Upper Oven for Baking or RoastingPreheating and Pan Placement OperatingBroil HI/LO pad again How to Set the Upper Oven for Broiling-Close the oven doorBroiling Guide HI BroilUsing the clock and timer Instructions SafetyInstallation Instructions Tips Operating Instructions Using the timed baking Roasting features upper oven onlyHow to Set an Immediate Start and Automatic Stop How to Set a Delayed Start and Automatic StopUsing the probe How to Set the Upper Oven For Roasting When Using the ProbeInsert the probe into the food Auto Recipe Conversion Using the convection ovenConvection Bake Convection RoastPaper and Plastic Installation Instructions Troubleshooting TipsMulti-Shelf Baking Cookware for Convection CookingTouch the Convection Roast pad Convection Roasting Guide Make sure the clock shows the correct time of day Using the timed convection Baking features upper oven onlyTones at the End of a Timed Cycle Special features of your upper oven controlFahrenheit or Celsius Temperature Selection Hour Shut-OffHour, 24 Hour or Clock Black-Out Safety Gas/Control Lockout on some modelsInstructions Cook and HoldUsing the Sabbath Feature. on some models How to Set for Regular Baking/RoastingHow to Exit the Sabbath Feature Adjust the upper oven thermostat-Do it yourself To Adjust the ThermostatType of margarine will affect baking performance To Use the Lower Oven Drawer Using the lower oven drawerAdjust the oven thermostat-Do it yourself Operating Instructions SafetyInstructions Operating Instructions Using the self-cleaning upper ovenBefore a Clean Cycle How to Set the Upper Oven for CleaningAfter a Clean Cycle How to Delay the Start of CleaningTo start Touch the Start pad Care and cleaning of the range Sealed Burner AssembliesTurn all controls OFF before removing the burner parts Burner Caps and Heads Tips Consumer Support Burner GratesCooktop Surface Griddle is to be used over the center burner only Griddle PrecautionsGriddle Stainless Steel Surfaces on some modelsOven Heating Elements To clean the inside of the doorTo clean the outside of the door Lift-Off Oven DoorSlide the drawer all the way Removable Lower Oven DrawerGlass Window To remove the drawer To replace the drawerOven Air Vents Upper Control PanelLower Control Panel and Knobs Do not remove any screws to remove the cover Oven Light ReplacementOven Shelves and Drawer Racks To removeIf you smell gas Installation of the rangeSafety Instructions Operating Instructions Instructions InstallationOperating Instructions Installation InstructionsDimensions and Clearances Gas line shut-off valve Operating Instructions SafetyGas Supply Requirements Recommended Gas Pipe Outlet Locations Safety InstructionsTroubleshooting Tips Consumer Support OperatingLocate the electric supply as illustrated Electrical Power Supply RequirementsProvide Proper Electrical Supply Recommended Electrical Outlet LocationsFlexible Connector Hookup Rigid Pipe Hookup Options Connect the Range to the Gas SupplyTeflon Registered trademark of DuPont Do not discard these screws Using an Existing Nema 14-50R ReceptacleReplace the Power Cord Optional Remove the wire cover on the backInsert the new power cord through the strain Wire Power Cord Installation OptionWire Conduit Installation Option Wire Conduit Installation Option Safety Instructions Replace the Wire CoverTips Consumer Caps Oval Center Burner Head/Cap AssemblySeal the Openings Assemble Surface BurnersLevel the Range Safety Instructions OperatingCheck Ignition of Surface Burners Quality of FlamesMust be performed by a qualified LP gas installer Instructions SafetyInstall the Anti-Tip Device When All Hookups Are CompletedBefore you call for service… Troubleshooting Tips Consumer SupportProblem Possible Causes What To Do Is set Clock and timerSelf-clean After a clean cycleSafety Instructions Operating Instructions Installation Controls improperly set See the Lower oven drawer section Wait for the self-clean cycle to finish and the ovenFully extend the drawer and push it all the way To coolLooking For Something More? AccessoriesConsumer Support GE Service Protection Plus We’ll Cover Any Appliance. Anywhere AnytimeConsumer Product Ownership Registration One Year GE Will ReplaceWhat GE Will Not Cover Warrantor General Electric Company. Louisville, KYWhat Mabe Will Not Cover GE Dual Fuel Range Warranty. For customers in CanadaInstructions Safety Instructions Mabe Will ReplaceInstallation Instructions GE Appliances Website Consumer Support
Related manuals
Manual 64 pages 46.44 Kb

C2S980 specifications

The GE C2S980,04-09 JR,49-85167-1,183D5580P249 is a sophisticated control system utilized in various industrial applications, specifically designed for enhancing efficiency and reliability. This model exemplifies advanced technologies and systems integration, catering to the needs of modern industries.

One of the main features of the GE C2S980 is its flexibility, allowing it to be integrated seamlessly into different types of systems. This adaptability makes it suitable for manufacturing plants, power generation facilities, and other industrial environments. The device is engineered for mobility and can be quickly deployed or modified according to the operational requirements of the facility.

A notable technology embedded within the GE C2S980 is its robust data acquisition capabilities. It can gather and process large volumes of data in real-time, which is crucial for effective monitoring and control. This feature enables operators to make informed decisions based on accurate and up-to-date information regarding equipment performance and system health.

Additionally, the GE C2S980 is equipped with advanced diagnostic tools. These tools assist in identifying faults and inefficiencies within the system, thereby reducing maintenance costs and minimizing downtime. Its built-in analytics engine helps in predictive maintenance, enabling industries to foresee potential issues before they escalate into serious problems.

The C2S980 also prioritizes user experience, featuring an intuitive interface that simplifies the navigation of complex controls. This user-friendly design reduces the learning curve for operators, enhancing overall productivity.

Another critical characteristic is its compliance with industry standards, ensuring safety and reliability in various applications. The system is designed to operate in challenging conditions and is built to withstand environmental factors, thus guaranteeing longevity and consistent performance.

In terms of connectivity, the GE C2S980 supports various protocols, facilitating interoperability with other devices and systems. This connectivity is essential for industries that rely on integrating multiple technologies into their operations.

Overall, the GE C2S980,04-09 JR,49-85167-1,183D5580P249 stands out due to its combination of advanced technology, user-centric design, and adaptability to diverse industrial environments, making it an invaluable asset for enhancing operational efficiencies.
Top Page Image Contents