GE C2S980 installation instructions Special features of your upper oven control, Hour Shut-Off

Page 24

Safety Instructions

Special features of your upper oven control.

Your new touch pad control has additional features that you may choose to use. The following are the features and how you may activate them.

The special feature modes can only be activated while the display is showing the time of day. They remain in the control’s memory until the steps are repeated.

When the display shows your choice, touch the START pad. The special features will remain in memory after a power failure.

12 Hour Shut-Off

Operating Instructions

With this feature, should you forget and leave the oven on, the control will automatically turn off the oven after 12 hours during baking functions or after 3 hours during a broil function.

If you wish to turn OFF this feature, follow the steps below.

Touch the BAKE and BROIL HI/LO pads at the same time for 3 seconds until the display shows SF.

Touch the DELAY START pad. The display will show 12 shdn (12 hour shut-off). Touch the DELAY START pad again and the display will show no shdn (no shut-off).

Touch the START pad to activate the no shut-off and leave the control set in this special features mode.

Installation

Instructions

Fahrenheit or Celsius Temperature Selection

Your oven control is set to use the Fahrenheit

Touch the BROIL HI/LO pad. The display

temperature selections but you may change

will show F (Fahrenheit).

this to use the Celsius selections.

Touch the BROIL HI/LO pad again.

 

Touch the BAKE and BROIL HI/LO pads

The display will show C (Celsius).

at the same time for 3 seconds until the

Touch the START pad.

display shows SF.

 

Consumer Support Troubleshooting Tips

Tones at the End of a Timed Cycle

At the end of a timed cycle, 3 short beeps will sound followed by one beep every 6 seconds until the CLEAR/OFF pad is touched. This continual 6 second beep may be canceled.

To cancel the 6 second beep:

Touch the BAKE and BROIL HI/LO pads at the same time for 3 seconds until the display shows SF.

Touch the KITCHEN TIMER ON/OFF pad. The display shows CON BEEP (continual beep). Touch the KITCHEN TIMER ON/OFF pad again. The display shows BEEP. (This cancels the one beep every 6 seconds.)

Touch the START pad.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Safety Instructions Troubleshooting TipsWrite the model and serial numbers here Model # Serial # Operating Instructions Safety Instructions Installation ANTI-TIP DeviceTroubleshooting Tips Consumer Support All ranges can tip and injury could resultGe.com Operating Instructions Safety Instructions Installation InstructionsConsumer Support Safety Safety Instructions Operating InstructionsLower Oven Drawer Instructions Safety Instructions Operating Installation InstructionsSupport Troubleshooting TipsUsing the gas surface burners SafetyInstructions Installation SupportUsing the griddle Safety InstructionsHow to Insert the Griddle Using the GriddleTroubleshooting Tips Case of Power FailureTop-of-Range Cookware Stove Top GrillsUsing the upper oven controls Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips Using the upper oven Instructions OperatingBefore you begin… Upper Oven VentHow to Set the Upper Oven for Baking or Roasting Preheating and Pan PlacementOperating Aluminum FoilHow to Set the Upper Oven for Broiling-Close the oven door Broiling GuideHI Broil Broil HI/LO pad againUsing the clock and timer Instructions SafetyInstallation Instructions Tips Using the timed baking Roasting features upper oven only How to Set an Immediate Start and Automatic StopHow to Set a Delayed Start and Automatic Stop Operating InstructionsUsing the probe How to Set the Upper Oven For Roasting When Using the ProbeInsert the probe into the food Using the convection oven Convection BakeConvection Roast Auto Recipe ConversionInstallation Instructions Troubleshooting Tips Multi-Shelf BakingCookware for Convection Cooking Paper and PlasticTouch the Convection Roast pad Convection Roasting Guide Using the timed convection Baking features upper oven only Make sure the clock shows the correct time of daySpecial features of your upper oven control Fahrenheit or Celsius Temperature SelectionHour Shut-Off Tones at the End of a Timed CycleSafety Gas/Control Lockout on some models InstructionsCook and Hold Hour, 24 Hour or Clock Black-OutUsing the Sabbath Feature. on some models How to Set for Regular Baking/RoastingHow to Exit the Sabbath Feature Adjust the upper oven thermostat-Do it yourself To Adjust the ThermostatType of margarine will affect baking performance Using the lower oven drawer Adjust the oven thermostat-Do it yourselfOperating Instructions Safety To Use the Lower Oven DrawerUsing the self-cleaning upper oven Before a Clean CycleHow to Set the Upper Oven for Cleaning Instructions Operating InstructionsAfter a Clean Cycle How to Delay the Start of CleaningTo start Touch the Start pad Care and cleaning of the range Sealed Burner AssembliesTurn all controls OFF before removing the burner parts Burner Caps and Heads Tips Consumer Support Burner GratesCooktop Surface Griddle Precautions GriddleStainless Steel Surfaces on some models Griddle is to be used over the center burner onlyTo clean the inside of the door To clean the outside of the doorLift-Off Oven Door Oven Heating ElementsRemovable Lower Oven Drawer Glass WindowTo remove the drawer To replace the drawer Slide the drawer all the wayOven Air Vents Upper Control PanelLower Control Panel and Knobs Oven Light Replacement Oven Shelves and Drawer RacksTo remove Do not remove any screws to remove the coverInstallation of the range Safety Instructions Operating InstructionsInstructions Installation If you smell gasInstallation Instructions Operating InstructionsDimensions and Clearances Operating Instructions Safety Gas line shut-off valveRecommended Gas Pipe Outlet Locations Safety Instructions Troubleshooting Tips Consumer SupportOperating Gas Supply RequirementsElectrical Power Supply Requirements Provide Proper Electrical SupplyRecommended Electrical Outlet Locations Locate the electric supply as illustratedFlexible Connector Hookup Rigid Pipe Hookup Options Connect the Range to the Gas SupplyTeflon Registered trademark of DuPont Using an Existing Nema 14-50R Receptacle Replace the Power Cord OptionalRemove the wire cover on the back Do not discard these screwsWire Power Cord Installation Option Insert the new power cord through the strainWire Conduit Installation Option Wire Conduit Installation Option Safety Instructions Replace the Wire CoverTips Consumer Oval Center Burner Head/Cap Assembly Seal the OpeningsAssemble Surface Burners CapsSafety Instructions Operating Check Ignition of Surface BurnersQuality of Flames Level the RangeInstructions Safety Install the Anti-Tip DeviceWhen All Hookups Are Completed Must be performed by a qualified LP gas installerBefore you call for service… Troubleshooting Tips Consumer SupportProblem Possible Causes What To Do Clock and timer Self-cleanAfter a clean cycle Is setSafety Instructions Operating Instructions Installation Wait for the self-clean cycle to finish and the oven Fully extend the drawer and push it all the wayTo cool Controls improperly set See the Lower oven drawer sectionAccessories Looking For Something More?Consumer Support We’ll Cover Any Appliance. Anywhere Anytime GE Service Protection PlusConsumer Product Ownership Registration GE Will Replace What GE Will Not CoverWarrantor General Electric Company. Louisville, KY One YearGE Dual Fuel Range Warranty. For customers in Canada Instructions Safety InstructionsMabe Will Replace What Mabe Will Not CoverInstallation Instructions Consumer Support GE Appliances Website
Related manuals
Manual 64 pages 46.44 Kb

C2S980 specifications

The GE C2S980,04-09 JR,49-85167-1,183D5580P249 is a sophisticated control system utilized in various industrial applications, specifically designed for enhancing efficiency and reliability. This model exemplifies advanced technologies and systems integration, catering to the needs of modern industries.

One of the main features of the GE C2S980 is its flexibility, allowing it to be integrated seamlessly into different types of systems. This adaptability makes it suitable for manufacturing plants, power generation facilities, and other industrial environments. The device is engineered for mobility and can be quickly deployed or modified according to the operational requirements of the facility.

A notable technology embedded within the GE C2S980 is its robust data acquisition capabilities. It can gather and process large volumes of data in real-time, which is crucial for effective monitoring and control. This feature enables operators to make informed decisions based on accurate and up-to-date information regarding equipment performance and system health.

Additionally, the GE C2S980 is equipped with advanced diagnostic tools. These tools assist in identifying faults and inefficiencies within the system, thereby reducing maintenance costs and minimizing downtime. Its built-in analytics engine helps in predictive maintenance, enabling industries to foresee potential issues before they escalate into serious problems.

The C2S980 also prioritizes user experience, featuring an intuitive interface that simplifies the navigation of complex controls. This user-friendly design reduces the learning curve for operators, enhancing overall productivity.

Another critical characteristic is its compliance with industry standards, ensuring safety and reliability in various applications. The system is designed to operate in challenging conditions and is built to withstand environmental factors, thus guaranteeing longevity and consistent performance.

In terms of connectivity, the GE C2S980 supports various protocols, facilitating interoperability with other devices and systems. This connectivity is essential for industries that rely on integrating multiple technologies into their operations.

Overall, the GE C2S980,04-09 JR,49-85167-1,183D5580P249 stands out due to its combination of advanced technology, user-centric design, and adaptability to diverse industrial environments, making it an invaluable asset for enhancing operational efficiencies.
Top Page Image Contents