GE C2S980 Connect the Range to the Gas Supply, Teflon Registered trademark of DuPont

Page 45

Read these instructions completely and carefully.

Connect the Range to the Gas Supply

Shut off the main gas supply valve before disconnecting the old range and leave it off until the new hookup has been completed. Don’t forget to relight the pilot on other gas appliances when you turn the gas back on.

Safety Instructions

Because hard piping restricts movement of the range, the use of a CSA International-certified flexible metal appliance connector is recommended unless local codes require a hard-piped connection.

Never use an old connector when installing a new range. If the hard piping method is used, you must carefully align the pipe; the range cannot be moved after the connection is made.

To prevent gas leaks, put pipe joint compound on, or wrap pipe thread tape with Teflon* around, all male (external) pipe threads.

Install a manual gas line shut-off valve in the gas line in an easily accessed location outside of the range. Make sure everyone operating the range knows where and how to shut off the gas supply to the range.

Install male 1/2″ flare union adapter to the 1/2″ NPT internal thread elbow at inlet of regulator. Use a backup wrench on the regulator fitting to avoid damage.

When installing the range from the front, remove the 90° elbow for easier installation.

Install male 1/2″ or 3/4″ flare union adapter to the NPT internal thread of the manual shut-off

valve, taking care to backup the shut-off valve to keep it from turning.

Connect flexible metal appliance connector to the adapter on the range. Position range to permit connection at the shut-off valve.

When all connections have been made, make sure all range controls are in the off position and turn on the main gas supply valve.

Use a liquid leak detector at all joints and connections to check for leaks in the system.

CAUTION : DO NOT USE A FLAME TO CHECK FOR GAS LEAKS.

When using test pressures greater than 1/2 psig to pressure test the gas supply system of the residence, disconnect the range and individual shut-off valve from the gas supply piping. When using test pressures of 1/2 psig or less to test the gas supply system, simply isolate the range from the gas supply system by closing the individual shut-off valve.

*Teflon: Registered trademark of DuPont

Operating Instructions

Instructions

Installation

Flexible Connector Hookup

Rigid Pipe Hookup Options

Gas Flow into Range

45° Elbow

Pressure regulator

Installer: Inform the consumer of the location of the gas shut-off valve.

Adapter

1/2″ or 3/4″ Gas pipe

Gas Flow into Range

Flex connector (6 ft. max.)

Adapter

Gas shut-off valve

 

 

90° Elbow

Nipple

 

 

Black

 

 

iron pipe

 

 

 

Pressure

 

 

Union

regulator

 

 

Union

 

 

 

Nipple

 

 

 

 

 

Gas

 

 

 

shut-off

Installer: Inform the consumer of the

 

valve

location of the gas shut-off valve.

 

1/2″ or 3/4″

 

 

 

Gas pipe

Alternate Hookup

 

Adapter

 

90° Elbow

 

90° Elbow

Nipple

 

Nipple

 

Quick connect

 

 

 

 

or union

Gas

 

Nipple

Pressure

 

regulator

shut-off

 

 

 

90°

valve

 

 

Elbow

 

 

1/2″ or 3/4″

 

 

 

Gas pipe

90° Elbow

 

Installer: Inform the consumer of the

Adapter

 

 

 

location of the gas shut-off valve.

Gas Flow into Range 45

Troubleshooting Tips Consumer Support

Page 44 Page 46
Image 45
Page 44 Page 46
Contents Safety Instructions Troubleshooting TipsWrite the model and serial numbers here Model # Serial # ANTI-TIP Device Operating Instructions Safety Instructions InstallationTroubleshooting Tips Consumer Support All ranges can tip and injury could resultGe.com Operating Instructions Safety Instructions Installation InstructionsConsumer Support Safety Operating Instructions Safety InstructionsLower Oven Drawer Operating Installation Instructions Instructions Safety InstructionsSupport Troubleshooting TipsSafety Using the gas surface burnersInstructions Installation SupportSafety Instructions Using the griddleHow to Insert the Griddle Using the GriddleCase of Power Failure Troubleshooting TipsTop-of-Range Cookware Stove Top GrillsUsing the upper oven controls Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips Instructions Operating Using the upper ovenBefore you begin… Upper Oven VentPreheating and Pan Placement How to Set the Upper Oven for Baking or RoastingOperating Aluminum FoilBroiling Guide How to Set the Upper Oven for Broiling-Close the oven doorHI Broil Broil HI/LO pad againUsing the clock and timer Instructions SafetyInstallation Instructions Tips How to Set an Immediate Start and Automatic Stop Using the timed baking Roasting features upper oven onlyHow to Set a Delayed Start and Automatic Stop Operating InstructionsUsing the probe How to Set the Upper Oven For Roasting When Using the ProbeInsert the probe into the food Convection Bake Using the convection ovenConvection Roast Auto Recipe ConversionMulti-Shelf Baking Installation Instructions Troubleshooting TipsCookware for Convection Cooking Paper and PlasticTouch the Convection Roast pad Convection Roasting Guide Make sure the clock shows the correct time of day Using the timed convection Baking features upper oven onlyFahrenheit or Celsius Temperature Selection Special features of your upper oven controlHour Shut-Off Tones at the End of a Timed CycleInstructions Safety Gas/Control Lockout on some modelsCook and Hold Hour, 24 Hour or Clock Black-OutUsing the Sabbath Feature. on some models How to Set for Regular Baking/RoastingHow to Exit the Sabbath Feature Adjust the upper oven thermostat-Do it yourself To Adjust the ThermostatType of margarine will affect baking performance Adjust the oven thermostat-Do it yourself Using the lower oven drawerOperating Instructions Safety To Use the Lower Oven DrawerBefore a Clean Cycle Using the self-cleaning upper ovenHow to Set the Upper Oven for Cleaning Instructions Operating InstructionsAfter a Clean Cycle How to Delay the Start of CleaningTo start Touch the Start pad Care and cleaning of the range Sealed Burner AssembliesTurn all controls OFF before removing the burner parts Burner Caps and Heads Tips Consumer Support Burner GratesCooktop Surface Griddle Griddle PrecautionsStainless Steel Surfaces on some models Griddle is to be used over the center burner onlyTo clean the outside of the door To clean the inside of the doorLift-Off Oven Door Oven Heating ElementsGlass Window Removable Lower Oven DrawerTo remove the drawer To replace the drawer Slide the drawer all the wayOven Air Vents Upper Control PanelLower Control Panel and Knobs Oven Shelves and Drawer Racks Oven Light ReplacementTo remove Do not remove any screws to remove the coverSafety Instructions Operating Instructions Installation of the rangeInstructions Installation If you smell gasOperating Instructions Installation InstructionsDimensions and Clearances Gas line shut-off valve Operating Instructions SafetyTroubleshooting Tips Consumer Support Recommended Gas Pipe Outlet Locations Safety InstructionsOperating Gas Supply RequirementsProvide Proper Electrical Supply Electrical Power Supply RequirementsRecommended Electrical Outlet Locations Locate the electric supply as illustratedFlexible Connector Hookup Rigid Pipe Hookup Options Connect the Range to the Gas SupplyTeflon Registered trademark of DuPont Replace the Power Cord Optional Using an Existing Nema 14-50R ReceptacleRemove the wire cover on the back Do not discard these screwsInsert the new power cord through the strain Wire Power Cord Installation OptionWire Conduit Installation Option Wire Conduit Installation Option Safety Instructions Replace the Wire CoverTips Consumer Seal the Openings Oval Center Burner Head/Cap AssemblyAssemble Surface Burners CapsCheck Ignition of Surface Burners Safety Instructions OperatingQuality of Flames Level the RangeInstall the Anti-Tip Device Instructions SafetyWhen All Hookups Are Completed Must be performed by a qualified LP gas installerBefore you call for service… Troubleshooting Tips Consumer SupportProblem Possible Causes What To Do Self-clean Clock and timerAfter a clean cycle Is setSafety Instructions Operating Instructions Installation Fully extend the drawer and push it all the way Wait for the self-clean cycle to finish and the ovenTo cool Controls improperly set See the Lower oven drawer sectionLooking For Something More? AccessoriesConsumer Support GE Service Protection Plus We’ll Cover Any Appliance. Anywhere AnytimeConsumer Product Ownership Registration What GE Will Not Cover GE Will ReplaceWarrantor General Electric Company. Louisville, KY One YearInstructions Safety Instructions GE Dual Fuel Range Warranty. For customers in CanadaMabe Will Replace What Mabe Will Not CoverInstallation Instructions GE Appliances Website Consumer Support
Related manuals
Manual 64 pages 46.44 Kb

C2S980 specifications

The GE C2S980,04-09 JR,49-85167-1,183D5580P249 is a sophisticated control system utilized in various industrial applications, specifically designed for enhancing efficiency and reliability. This model exemplifies advanced technologies and systems integration, catering to the needs of modern industries.

One of the main features of the GE C2S980 is its flexibility, allowing it to be integrated seamlessly into different types of systems. This adaptability makes it suitable for manufacturing plants, power generation facilities, and other industrial environments. The device is engineered for mobility and can be quickly deployed or modified according to the operational requirements of the facility.

A notable technology embedded within the GE C2S980 is its robust data acquisition capabilities. It can gather and process large volumes of data in real-time, which is crucial for effective monitoring and control. This feature enables operators to make informed decisions based on accurate and up-to-date information regarding equipment performance and system health.

Additionally, the GE C2S980 is equipped with advanced diagnostic tools. These tools assist in identifying faults and inefficiencies within the system, thereby reducing maintenance costs and minimizing downtime. Its built-in analytics engine helps in predictive maintenance, enabling industries to foresee potential issues before they escalate into serious problems.

The C2S980 also prioritizes user experience, featuring an intuitive interface that simplifies the navigation of complex controls. This user-friendly design reduces the learning curve for operators, enhancing overall productivity.

Another critical characteristic is its compliance with industry standards, ensuring safety and reliability in various applications. The system is designed to operate in challenging conditions and is built to withstand environmental factors, thus guaranteeing longevity and consistent performance.

In terms of connectivity, the GE C2S980 supports various protocols, facilitating interoperability with other devices and systems. This connectivity is essential for industries that rely on integrating multiple technologies into their operations.

Overall, the GE C2S980,04-09 JR,49-85167-1,183D5580P249 stands out due to its combination of advanced technology, user-centric design, and adaptability to diverse industrial environments, making it an invaluable asset for enhancing operational efficiencies.
Top Page Image Contents