GE C2S980 Using the probe, How to Set the Upper Oven For Roasting When Using the Probe

Page 18

Instructions

Using the probe.

For many foods, especially roasts and poultry, internal food temperature is the best test for doneness.

The temperature probe takes the guesswork out of roasting by cooking foods to the exact doneness you want.

Operating Instructions Safety

The temperature probe has a skewer-like probe at one end and a plug at the other end that goes into the outlet in the oven.

Use of probes other than the one provided with this product may result in damage to the probe.

Use the handles of the probe and plug when inserting and removing them from the food and outlet.

■To avoid damaging your probe, do not use tongs to pull on the cable when removing it.

■To avoid breaking the probe, make sure food is completely defrosted before inserting.

■To prevent possible burns, do not unplug the probe from the outlet until the oven has cooled.

Cable

Plug

Probe

Handles

■Never leave your probe inside the oven during a self-cleaning cycle.

■Do not store the probe in the oven.

Installation

Instructions

After preparing the meat and placing it on a trivet or on a broiler pan grid, follow these directions for proper probe placement.

Insert the probe completely into the meat. It should not touch the bone, fat or gristle.

For roasts with no bone, insert the probe into the meatiest part of the roast. For bone-in ham or lamb, insert the probe into the center of the lowest large muscle.

Insert the probe into the center of dishes such as meat loaf or casseroles.

Insert the probe into the meatiest part of the inner thigh from below and parallel to the leg of a whole turkey.

How to Set the Upper Oven For Roasting When Using the Probe

Consumer Support Troubleshooting Tips

Insert the probe into the food.

Plug the probe into the outlet in the oven. Make sure it’s pushed all the way in. Close the oven door.

Touch the PROBE pad.

Touch the number pads to set the desired internal food or meat temperature.

Touch the BAKE pad.

Touch the number pads to set the desired oven temperature.

Touch the START pad.

The display will flash if the probe is inserted into the outlet and you have not set a probe temperature and touched the START pad.

After the internal temperature of the food reaches 100°F, the changing internal temperature will be shown in the display.

When the internal temperature of the food reaches the number you have set, the probe and the oven turn off and the oven control signals. To stop the signal, touch the CLEAR/OFF pad. Use hot pads to remove the probe from the food. Do not use tongs to pull on it—they might damage it.

To change the oven temperature during the Roast cycle, touch the BAKE pad and then the number pads to set the new temperature.

■If the probe is removed from the food before the final temperature is reached, a tone will sound and the display will flash until the probe is removed from the oven.

■You can use the timer even though you cannot use timed oven operations while using the probe.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Safety Instructions Troubleshooting TipsWrite the model and serial numbers here Model # Serial # Operating Instructions Safety Instructions Installation ANTI-TIP DeviceTroubleshooting Tips Consumer Support All ranges can tip and injury could resultGe.com Operating Instructions Safety Instructions Installation InstructionsConsumer Support Safety Safety Instructions Operating InstructionsLower Oven Drawer Support Troubleshooting Instructions Safety InstructionsOperating Installation Instructions TipsInstructions Installation Using the gas surface burnersSafety SupportHow to Insert the Griddle Using the griddleSafety Instructions Using the GriddleTop-of-Range Cookware Troubleshooting TipsCase of Power Failure Stove Top GrillsUsing the upper oven controls Operating Instructions Safety InstructionsConsumer Support Troubleshooting Tips Before you begin… Using the upper ovenInstructions Operating Upper Oven VentOperating How to Set the Upper Oven for Baking or RoastingPreheating and Pan Placement Aluminum FoilHI Broil How to Set the Upper Oven for Broiling-Close the oven doorBroiling Guide Broil HI/LO pad againUsing the clock and timer Instructions SafetyInstallation Instructions Tips How to Set a Delayed Start and Automatic Stop Using the timed baking Roasting features upper oven onlyHow to Set an Immediate Start and Automatic Stop Operating InstructionsUsing the probe How to Set the Upper Oven For Roasting When Using the ProbeInsert the probe into the food Convection Roast Using the convection ovenConvection Bake Auto Recipe ConversionCookware for Convection Cooking Installation Instructions Troubleshooting TipsMulti-Shelf Baking Paper and PlasticTouch the Convection Roast pad Convection Roasting Guide Using the timed convection Baking features upper oven only Make sure the clock shows the correct time of dayHour Shut-Off Special features of your upper oven controlFahrenheit or Celsius Temperature Selection Tones at the End of a Timed CycleCook and Hold Safety Gas/Control Lockout on some modelsInstructions Hour, 24 Hour or Clock Black-OutUsing the Sabbath Feature. on some models How to Set for Regular Baking/RoastingHow to Exit the Sabbath Feature Adjust the upper oven thermostat-Do it yourself To Adjust the ThermostatType of margarine will affect baking performance Operating Instructions Safety Using the lower oven drawerAdjust the oven thermostat-Do it yourself To Use the Lower Oven DrawerHow to Set the Upper Oven for Cleaning Using the self-cleaning upper ovenBefore a Clean Cycle Instructions Operating InstructionsAfter a Clean Cycle How to Delay the Start of CleaningTo start Touch the Start pad Care and cleaning of the range Sealed Burner AssembliesTurn all controls OFF before removing the burner parts Burner Caps and Heads Tips Consumer Support Burner GratesCooktop Surface Stainless Steel Surfaces on some models Griddle PrecautionsGriddle Griddle is to be used over the center burner onlyLift-Off Oven Door To clean the inside of the doorTo clean the outside of the door Oven Heating ElementsTo remove the drawer To replace the drawer Removable Lower Oven DrawerGlass Window Slide the drawer all the wayOven Air Vents Upper Control PanelLower Control Panel and Knobs To remove Oven Light ReplacementOven Shelves and Drawer Racks Do not remove any screws to remove the coverInstructions Installation Installation of the rangeSafety Instructions Operating Instructions If you smell gasInstallation Instructions Operating InstructionsDimensions and Clearances Operating Instructions Safety Gas line shut-off valveOperating Recommended Gas Pipe Outlet Locations Safety InstructionsTroubleshooting Tips Consumer Support Gas Supply RequirementsRecommended Electrical Outlet Locations Electrical Power Supply RequirementsProvide Proper Electrical Supply Locate the electric supply as illustratedFlexible Connector Hookup Rigid Pipe Hookup Options Connect the Range to the Gas SupplyTeflon Registered trademark of DuPont Remove the wire cover on the back Using an Existing Nema 14-50R ReceptacleReplace the Power Cord Optional Do not discard these screwsWire Power Cord Installation Option Insert the new power cord through the strainWire Conduit Installation Option Wire Conduit Installation Option Safety Instructions Replace the Wire CoverTips Consumer Assemble Surface Burners Oval Center Burner Head/Cap AssemblySeal the Openings CapsQuality of Flames Safety Instructions OperatingCheck Ignition of Surface Burners Level the RangeWhen All Hookups Are Completed Instructions SafetyInstall the Anti-Tip Device Must be performed by a qualified LP gas installerBefore you call for service… Troubleshooting Tips Consumer SupportProblem Possible Causes What To Do After a clean cycle Clock and timerSelf-clean Is setSafety Instructions Operating Instructions Installation To cool Wait for the self-clean cycle to finish and the ovenFully extend the drawer and push it all the way Controls improperly set See the Lower oven drawer sectionAccessories Looking For Something More?Consumer Support We’ll Cover Any Appliance. Anywhere Anytime GE Service Protection PlusConsumer Product Ownership Registration Warrantor General Electric Company. Louisville, KY GE Will ReplaceWhat GE Will Not Cover One YearMabe Will Replace GE Dual Fuel Range Warranty. For customers in CanadaInstructions Safety Instructions What Mabe Will Not CoverInstallation Instructions Consumer Support GE Appliances Website
Related manuals
Manual 64 pages 46.44 Kb

C2S980 specifications

The GE C2S980,04-09 JR,49-85167-1,183D5580P249 is a sophisticated control system utilized in various industrial applications, specifically designed for enhancing efficiency and reliability. This model exemplifies advanced technologies and systems integration, catering to the needs of modern industries.

One of the main features of the GE C2S980 is its flexibility, allowing it to be integrated seamlessly into different types of systems. This adaptability makes it suitable for manufacturing plants, power generation facilities, and other industrial environments. The device is engineered for mobility and can be quickly deployed or modified according to the operational requirements of the facility.

A notable technology embedded within the GE C2S980 is its robust data acquisition capabilities. It can gather and process large volumes of data in real-time, which is crucial for effective monitoring and control. This feature enables operators to make informed decisions based on accurate and up-to-date information regarding equipment performance and system health.

Additionally, the GE C2S980 is equipped with advanced diagnostic tools. These tools assist in identifying faults and inefficiencies within the system, thereby reducing maintenance costs and minimizing downtime. Its built-in analytics engine helps in predictive maintenance, enabling industries to foresee potential issues before they escalate into serious problems.

The C2S980 also prioritizes user experience, featuring an intuitive interface that simplifies the navigation of complex controls. This user-friendly design reduces the learning curve for operators, enhancing overall productivity.

Another critical characteristic is its compliance with industry standards, ensuring safety and reliability in various applications. The system is designed to operate in challenging conditions and is built to withstand environmental factors, thus guaranteeing longevity and consistent performance.

In terms of connectivity, the GE C2S980 supports various protocols, facilitating interoperability with other devices and systems. This connectivity is essential for industries that rely on integrating multiple technologies into their operations.

Overall, the GE C2S980,04-09 JR,49-85167-1,183D5580P249 stands out due to its combination of advanced technology, user-centric design, and adaptability to diverse industrial environments, making it an invaluable asset for enhancing operational efficiencies.
Top Page Image Contents