GE C2S980 Using the self-cleaning upper oven, Instructions Operating Instructions

Page 29

Using the self-cleaning upper oven.

ge.com

The oven door must be closed and all controls set correctly for the cycle to work properly.

Safety

Wipe up heavy soil on the oven bottom.

Before a Clean Cycle

For the first self-clean cycle, we recommend venting your kitchen with an open window or using a ventilation fan or hood.

Remove the shelves, any broiler pan, broiler grid, probe, all cookware and any aluminum foil from the oven.

The oven shelves can be self-cleaned, but they will darken, lose their luster and become hard to slide.

Soil on the front frame of the range and outside the gasket on the door will need to be cleaned by hand. Clean these areas with hot water, soap-filled scouring pads or cleansers such as Soft Scrub®. Rinse well with clean water and dry.

Do not clean the gasket. The fiberglass material of the oven door gasket cannot withstand abrasion. It is essential for the gasket to remain intact. If you notice it becoming worn or frayed, replace it.

Wipe up any heavy spillovers on the oven bottom.

Make sure the oven light bulb cover is in place and the oven light is off.

IMPORTANT: The health of some birds is extremely sensitive to the fumes given off during the self-cleaning cycle of any range. Move birds to another well-ventilated room.

NOTE: Use caution when opening the upper oven after the self-clean cycle has ended. The oven may still be hot.

Instructions Operating Instructions

How to Set the Upper Oven for Cleaning

Touch and hold the GAS/CONTROL LOCKOUT pad for 3 seconds to turn it off. See the Gas/Control Lockout section.

NOTE: The surface burners must be turned off prior to the self-clean start time.

Touch the SELF CLEAN pad.

Using the number pads, enter the desired clean time, if a time other than 4 hours is needed.

Clean cycle time is normally 4 hours. You can change the clean time to any time between

3 hours and 5 hours, depending on how dirty your oven is.

Touch the START pad.

The door locks automatically. The display will show the clean time remaining. It will not be possible to open the oven door until the temperature drops below the lock temperature and the LOCKED DOOR light goes off.

The oven shuts off automatically when the clean cycle is complete.

When the LOCKED DOOR light is off, the door will unlock automatically.

The words LOCK DOOR will flash and the oven control will signal if you set the clean cycle and forget to close the oven door.

To stop a clean cycle, touch the CLEAR/OFF pad. When the LOCKED DOOR light goes off indicating the oven has cooled below the locking temperature, you may open the door.

Do not use the lower oven drawer during a self-clean cycle.

Troubleshooting Tips Consumer Support

29

Image 29
Contents Write the model and serial numbers here Model # Serial # Safety InstructionsTroubleshooting Tips ANTI-TIP Device Operating Instructions Safety Instructions InstallationGe.com Troubleshooting Tips Consumer SupportAll ranges can tip and injury could result Consumer Support Operating Instructions Safety InstructionsInstallation Instructions Safety Operating Instructions Safety InstructionsLower Oven Drawer Operating Installation Instructions Instructions Safety InstructionsSupport Troubleshooting TipsSafety Using the gas surface burnersInstructions Installation SupportSafety Instructions Using the griddleHow to Insert the Griddle Using the GriddleCase of Power Failure Troubleshooting TipsTop-of-Range Cookware Stove Top GrillsConsumer Support Troubleshooting Tips Using the upper oven controlsOperating Instructions Safety Instructions Instructions Operating Using the upper ovenBefore you begin… Upper Oven VentPreheating and Pan Placement How to Set the Upper Oven for Baking or RoastingOperating Aluminum FoilBroiling Guide How to Set the Upper Oven for Broiling-Close the oven doorHI Broil Broil HI/LO pad againInstallation Instructions Tips Using the clock and timerInstructions Safety How to Set an Immediate Start and Automatic Stop Using the timed baking Roasting features upper oven onlyHow to Set a Delayed Start and Automatic Stop Operating InstructionsInsert the probe into the food Using the probeHow to Set the Upper Oven For Roasting When Using the Probe Convection Bake Using the convection ovenConvection Roast Auto Recipe ConversionMulti-Shelf Baking Installation Instructions Troubleshooting TipsCookware for Convection Cooking Paper and PlasticTouch the Convection Roast pad Convection Roasting Guide Make sure the clock shows the correct time of day Using the timed convection Baking features upper oven onlyFahrenheit or Celsius Temperature Selection Special features of your upper oven controlHour Shut-Off Tones at the End of a Timed CycleInstructions Safety Gas/Control Lockout on some modelsCook and Hold Hour, 24 Hour or Clock Black-OutHow to Exit the Sabbath Feature Using the Sabbath Feature. on some modelsHow to Set for Regular Baking/Roasting Type of margarine will affect baking performance Adjust the upper oven thermostat-Do it yourselfTo Adjust the Thermostat Adjust the oven thermostat-Do it yourself Using the lower oven drawerOperating Instructions Safety To Use the Lower Oven DrawerBefore a Clean Cycle Using the self-cleaning upper ovenHow to Set the Upper Oven for Cleaning Instructions Operating InstructionsTo start Touch the Start pad After a Clean CycleHow to Delay the Start of Cleaning Turn all controls OFF before removing the burner parts Care and cleaning of the rangeSealed Burner Assemblies Burner Caps and Heads Cooktop Surface Tips Consumer SupportBurner Grates Griddle Griddle PrecautionsStainless Steel Surfaces on some models Griddle is to be used over the center burner onlyTo clean the outside of the door To clean the inside of the doorLift-Off Oven Door Oven Heating ElementsGlass Window Removable Lower Oven DrawerTo remove the drawer To replace the drawer Slide the drawer all the wayLower Control Panel and Knobs Oven Air VentsUpper Control Panel Oven Shelves and Drawer Racks Oven Light ReplacementTo remove Do not remove any screws to remove the coverSafety Instructions Operating Instructions Installation of the rangeInstructions Installation If you smell gasOperating Instructions Installation InstructionsDimensions and Clearances Gas line shut-off valve Operating Instructions SafetyTroubleshooting Tips Consumer Support Recommended Gas Pipe Outlet Locations Safety InstructionsOperating Gas Supply RequirementsProvide Proper Electrical Supply Electrical Power Supply RequirementsRecommended Electrical Outlet Locations Locate the electric supply as illustratedTeflon Registered trademark of DuPont Flexible Connector Hookup Rigid Pipe Hookup OptionsConnect the Range to the Gas Supply Replace the Power Cord Optional Using an Existing Nema 14-50R ReceptacleRemove the wire cover on the back Do not discard these screwsInsert the new power cord through the strain Wire Power Cord Installation OptionWire Conduit Installation Option Tips Consumer Wire Conduit Installation Option Safety InstructionsReplace the Wire Cover Seal the Openings Oval Center Burner Head/Cap AssemblyAssemble Surface Burners CapsCheck Ignition of Surface Burners Safety Instructions OperatingQuality of Flames Level the RangeInstall the Anti-Tip Device Instructions SafetyWhen All Hookups Are Completed Must be performed by a qualified LP gas installerProblem Possible Causes What To Do Before you call for service…Troubleshooting Tips Consumer Support Self-clean Clock and timerAfter a clean cycle Is setSafety Instructions Operating Instructions Installation Fully extend the drawer and push it all the way Wait for the self-clean cycle to finish and the ovenTo cool Controls improperly set See the Lower oven drawer sectionLooking For Something More? AccessoriesConsumer Support GE Service Protection Plus We’ll Cover Any Appliance. Anywhere AnytimeConsumer Product Ownership Registration What GE Will Not Cover GE Will ReplaceWarrantor General Electric Company. Louisville, KY One YearInstructions Safety Instructions GE Dual Fuel Range Warranty. For customers in CanadaMabe Will Replace What Mabe Will Not CoverInstallation Instructions GE Appliances Website Consumer Support
Related manuals
Manual 64 pages 46.44 Kb

C2S980 specifications

The GE C2S980,04-09 JR,49-85167-1,183D5580P249 is a sophisticated control system utilized in various industrial applications, specifically designed for enhancing efficiency and reliability. This model exemplifies advanced technologies and systems integration, catering to the needs of modern industries.

One of the main features of the GE C2S980 is its flexibility, allowing it to be integrated seamlessly into different types of systems. This adaptability makes it suitable for manufacturing plants, power generation facilities, and other industrial environments. The device is engineered for mobility and can be quickly deployed or modified according to the operational requirements of the facility.

A notable technology embedded within the GE C2S980 is its robust data acquisition capabilities. It can gather and process large volumes of data in real-time, which is crucial for effective monitoring and control. This feature enables operators to make informed decisions based on accurate and up-to-date information regarding equipment performance and system health.

Additionally, the GE C2S980 is equipped with advanced diagnostic tools. These tools assist in identifying faults and inefficiencies within the system, thereby reducing maintenance costs and minimizing downtime. Its built-in analytics engine helps in predictive maintenance, enabling industries to foresee potential issues before they escalate into serious problems.

The C2S980 also prioritizes user experience, featuring an intuitive interface that simplifies the navigation of complex controls. This user-friendly design reduces the learning curve for operators, enhancing overall productivity.

Another critical characteristic is its compliance with industry standards, ensuring safety and reliability in various applications. The system is designed to operate in challenging conditions and is built to withstand environmental factors, thus guaranteeing longevity and consistent performance.

In terms of connectivity, the GE C2S980 supports various protocols, facilitating interoperability with other devices and systems. This connectivity is essential for industries that rely on integrating multiple technologies into their operations.

Overall, the GE C2S980,04-09 JR,49-85167-1,183D5580P249 stands out due to its combination of advanced technology, user-centric design, and adaptability to diverse industrial environments, making it an invaluable asset for enhancing operational efficiencies.