GE C2S980 Tips Consumer, Wire Conduit Installation Option Safety Instructions

Page 49

Read these instructions completely and carefully.

Replace the Power Cord (Optional) Continued

Perform this step only if the power cord shipped on the range does not match your wall receptacle.

4-Wire Conduit Installation Option

Safety Instructions

Remove the strain relief clamp from the bracket.

Assemble the squeeze connector (obtained locally), matching the diameter of your conduit, in the bracket hole. Insert the conduit through the squeeze connector. Allow enough slack to easily attach the wires to the terminal block.

NOTE: Do not install the conduit without a squeeze connector.

Insert the ground bare wire tip between the range frame and the ground plate (removed earlier) and secure it in place with the ground screw (removed earlier). Insert the bare wire (white/neutral) tip through the bottom center of the terminal block opening. Insert the two side bare wire tips into the lower left and the lower right terminal block openings. Tighten the screws until the wire is firmly secure (approximately 20 inch-lbs.).

NOTE: Make sure the wire is completely inserted into the terminal block and a secure connection is made.

Secure the squeeze connector in place in the bracket by tightening the squeeze connector screws.

NOTE: ALUMINUM WIRING:

Squeeze connector

Conduit

Terminal block

Wire tips

Ground screw

Bracket

Ground plate (grounding to range)

Bracket

Operating Instructions

Instructions

Installation

 

 

Aluminum building wire may be used but it must be rated for the correct amperage and voltage to make connection.

Wire used, location and enclosure

of splices, etc., must conform to good wiring practices and local codes.

Troubleshooting

Replace the Wire Cover

Replace the wire cover on the range back by sliding its right edge under the retaining tab and replacing the two screws removed earlier. Make sure that no wires are pinched between the cover and the range back.

2screws to replace wire cover

Retaining tab

Wire cover

Tips Consumer

Back of range

49

Support

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Troubleshooting Tips Safety InstructionsWrite the model and serial numbers here Model # Serial # ANTI-TIP Device Operating Instructions Safety Instructions InstallationAll ranges can tip and injury could result Troubleshooting Tips Consumer SupportGe.com Installation Instructions Operating Instructions Safety InstructionsConsumer Support Safety Operating Instructions Safety InstructionsLower Oven Drawer Operating Installation Instructions Instructions Safety InstructionsSupport Troubleshooting TipsSafety Using the gas surface burnersInstructions Installation SupportSafety Instructions Using the griddleHow to Insert the Griddle Using the GriddleCase of Power Failure Troubleshooting TipsTop-of-Range Cookware Stove Top GrillsOperating Instructions Safety Instructions Using the upper oven controlsConsumer Support Troubleshooting Tips Instructions Operating Using the upper ovenBefore you begin… Upper Oven VentPreheating and Pan Placement How to Set the Upper Oven for Baking or RoastingOperating Aluminum FoilBroiling Guide How to Set the Upper Oven for Broiling-Close the oven doorHI Broil Broil HI/LO pad againInstructions Safety Using the clock and timerInstallation Instructions Tips How to Set an Immediate Start and Automatic Stop Using the timed baking Roasting features upper oven onlyHow to Set a Delayed Start and Automatic Stop Operating InstructionsHow to Set the Upper Oven For Roasting When Using the Probe Using the probeInsert the probe into the food Convection Bake Using the convection ovenConvection Roast Auto Recipe ConversionMulti-Shelf Baking Installation Instructions Troubleshooting TipsCookware for Convection Cooking Paper and PlasticTouch the Convection Roast pad Convection Roasting Guide Make sure the clock shows the correct time of day Using the timed convection Baking features upper oven onlyFahrenheit or Celsius Temperature Selection Special features of your upper oven controlHour Shut-Off Tones at the End of a Timed CycleInstructions Safety Gas/Control Lockout on some modelsCook and Hold Hour, 24 Hour or Clock Black-OutHow to Set for Regular Baking/Roasting Using the Sabbath Feature. on some modelsHow to Exit the Sabbath Feature To Adjust the Thermostat Adjust the upper oven thermostat-Do it yourselfType of margarine will affect baking performance Adjust the oven thermostat-Do it yourself Using the lower oven drawerOperating Instructions Safety To Use the Lower Oven DrawerBefore a Clean Cycle Using the self-cleaning upper ovenHow to Set the Upper Oven for Cleaning Instructions Operating InstructionsHow to Delay the Start of Cleaning After a Clean CycleTo start Touch the Start pad Sealed Burner Assemblies Care and cleaning of the rangeTurn all controls OFF before removing the burner parts Burner Caps and Heads Burner Grates Tips Consumer SupportCooktop Surface Griddle Griddle PrecautionsStainless Steel Surfaces on some models Griddle is to be used over the center burner onlyTo clean the outside of the door To clean the inside of the doorLift-Off Oven Door Oven Heating ElementsGlass Window Removable Lower Oven DrawerTo remove the drawer To replace the drawer Slide the drawer all the wayUpper Control Panel Oven Air VentsLower Control Panel and Knobs Oven Shelves and Drawer Racks Oven Light ReplacementTo remove Do not remove any screws to remove the coverSafety Instructions Operating Instructions Installation of the rangeInstructions Installation If you smell gasOperating Instructions Installation InstructionsDimensions and Clearances Gas line shut-off valve Operating Instructions SafetyTroubleshooting Tips Consumer Support Recommended Gas Pipe Outlet Locations Safety InstructionsOperating Gas Supply RequirementsProvide Proper Electrical Supply Electrical Power Supply RequirementsRecommended Electrical Outlet Locations Locate the electric supply as illustratedConnect the Range to the Gas Supply Flexible Connector Hookup Rigid Pipe Hookup OptionsTeflon Registered trademark of DuPont Replace the Power Cord Optional Using an Existing Nema 14-50R ReceptacleRemove the wire cover on the back Do not discard these screwsInsert the new power cord through the strain Wire Power Cord Installation OptionWire Conduit Installation Option Replace the Wire Cover Wire Conduit Installation Option Safety InstructionsTips Consumer Seal the Openings Oval Center Burner Head/Cap AssemblyAssemble Surface Burners CapsCheck Ignition of Surface Burners Safety Instructions OperatingQuality of Flames Level the RangeInstall the Anti-Tip Device Instructions SafetyWhen All Hookups Are Completed Must be performed by a qualified LP gas installerTroubleshooting Tips Consumer Support Before you call for service…Problem Possible Causes What To Do Self-clean Clock and timerAfter a clean cycle Is setSafety Instructions Operating Instructions Installation Fully extend the drawer and push it all the way Wait for the self-clean cycle to finish and the ovenTo cool Controls improperly set See the Lower oven drawer sectionLooking For Something More? AccessoriesConsumer Support GE Service Protection Plus We’ll Cover Any Appliance. Anywhere AnytimeConsumer Product Ownership Registration What GE Will Not Cover GE Will ReplaceWarrantor General Electric Company. Louisville, KY One YearInstructions Safety Instructions GE Dual Fuel Range Warranty. For customers in CanadaMabe Will Replace What Mabe Will Not CoverInstallation Instructions GE Appliances Website Consumer Support
Related manuals
Manual 64 pages 46.44 Kb

C2S980 specifications

The GE C2S980,04-09 JR,49-85167-1,183D5580P249 is a sophisticated control system utilized in various industrial applications, specifically designed for enhancing efficiency and reliability. This model exemplifies advanced technologies and systems integration, catering to the needs of modern industries.

One of the main features of the GE C2S980 is its flexibility, allowing it to be integrated seamlessly into different types of systems. This adaptability makes it suitable for manufacturing plants, power generation facilities, and other industrial environments. The device is engineered for mobility and can be quickly deployed or modified according to the operational requirements of the facility.

A notable technology embedded within the GE C2S980 is its robust data acquisition capabilities. It can gather and process large volumes of data in real-time, which is crucial for effective monitoring and control. This feature enables operators to make informed decisions based on accurate and up-to-date information regarding equipment performance and system health.

Additionally, the GE C2S980 is equipped with advanced diagnostic tools. These tools assist in identifying faults and inefficiencies within the system, thereby reducing maintenance costs and minimizing downtime. Its built-in analytics engine helps in predictive maintenance, enabling industries to foresee potential issues before they escalate into serious problems.

The C2S980 also prioritizes user experience, featuring an intuitive interface that simplifies the navigation of complex controls. This user-friendly design reduces the learning curve for operators, enhancing overall productivity.

Another critical characteristic is its compliance with industry standards, ensuring safety and reliability in various applications. The system is designed to operate in challenging conditions and is built to withstand environmental factors, thus guaranteeing longevity and consistent performance.

In terms of connectivity, the GE C2S980 supports various protocols, facilitating interoperability with other devices and systems. This connectivity is essential for industries that rely on integrating multiple technologies into their operations.

Overall, the GE C2S980,04-09 JR,49-85167-1,183D5580P249 stands out due to its combination of advanced technology, user-centric design, and adaptability to diverse industrial environments, making it an invaluable asset for enhancing operational efficiencies.
Top Page Image Contents