GE 164D2966P205-1 Care and Cleaning, Lift-Off Oven Door, To remove the door, Inside of the door

Page 35

Lift-Off Oven Door

The oven door is

removable, but it is heavy. You may need help removing and replacing the door. Do not lift the

door by the handle. This can cause the glass to

break or can cause damage to the door.

To remove the door,

open it a few inches to the special stop position that will hold the door open. Grasp firmly on each side and lift the door straight up and off the hinges.

NOTE:

•Be careful not to place hands between the hinge and the oven door frame as the hinge could snap back and pinch fingers.

•While working in the oven area, cover the hinges with towels or empty paper towel rolls to prevent pinched fingers and chipping the porcelain enamel on the frame.

To replace the door, make sure the hinges are in the special stop position. Position the slots in the bottom of the door squarely over the hinges. Then lower the door slowly and evenly over both hinges at the same time. If hinges snap back against the oven frame, pull them back out.

TO CLEAN THE DOOR:

Inside of the door:

•Because the area inside the gasket is cleaned during the self-clean cycle, you do not need to clean this by hand. Any soap left on the liner causes additional stains when the oven is heated.

•The area outside the gasket can be cleaned with a soap-filled scouring pad.

•Do not rub or clean the door gasket—the fiberglass material of the gasket has an extremely low resistance to abrasion. An intact and well-fitting oven door gasket is essential for energy-efficient oven operation and good baking results. If you notice the gasket becoming worn, frayed or damaged in any way or if it has become displaced on the door, you should have it replaced.

NOTE: The gasket is designed with a gap at the bottom to allow for proper air circulation.

Inside gasket

Gasket

Outside gasket

Outside of the door:

•Use soap and water to thoroughly clean the top, sides and front of the oven door. DO NOT let water run down through openings in the top of the door. Rinse well. You may also use a glass cleaner to clean the glass on the outside of the door.

•Spillage of marinades, fruit juices, tomato sauces and basting materials containing acids may cause discoloration and should be wiped up immediately. When surface is cool, clean and rinse.

•Do not use oven cleaners, cleansing powders or harsh abrasives on the outside of the door.

(continued next page)

35

Care and Cleaning

Page 34 Page 36
Image 35
Page 34 Page 36
Contents UseandCare Guide Help US Help YOU… If YOU Need SERVICE…If You Need Service Important Safety Instructions Important Safety InstructionsOven Self-Cleaning OvenSave These Instructions Features of Your Ovens Features of Your OvensFeatures of Your Oven Control Oven Control, Clock Oven CONTROL, Clock and TimerTimer Your Oven ControlPreheat Notification Tone Special Features of Your Oven ControlTones While Setting the Control Fahrenheit or Centigrade Temperature SelectionSpecial Control, Clock and TimerFeatures of Your Oven Control OvenShelf Positions Using Your OvenBefore Using Your Oven Oven ShelvesCooking Using Your OvenConvection Cooking Multi-Shelf Baking When baking on Three shelves, placeConvection Baking Timed Convection Baking How to Convection Time BakeTimed Convection Baking Convection BakingEasy Steps How to Set Delay Start and Automatic Stop Convection BakeUsing Convection Conversion To convert the oven temperature for convection bakingConvection Roasting Convection RoastingTimed Convection BakingWord LO will be in the display Convection Roasting Convection Roasting Guide How to Set Your Oven for BakingConvection Roasting Guide BakingType of Food Shelf Position Pan PlacementPreheating Baking PansAluminum Foil CookiesPies CakesTimed Baking How to Set Your Oven for Time BakeHow to Set Immediate Start and Automatic Stop Timed Baking How to Set Delay Start and Automatic StopTo Adjust the Thermostat Adjust the Oven ThermostatRoasting Adjust the OvenRoasting ThermostatYour double oven has a probe in the upper oven only Roasting with the ProbeHam or Lamb Casseroles or Fish Roasting with the Probe How to Set the Oven When Using the Temperature ProbeFrozen Roasts Questions and AnswersWhy is my roast crumbling when I try to carve it? Roasting GuideRoasting Guide Broiling How to Set Your Oven for BroilingBroiling Should I salt the meat before broiling? Why are my meats not turning out as brown as they should?Oven door should be open to the broil stop position Broiling GuideBroiling Guide Before a Clean Cycle Operating the SELF-CLEANING OvenTo Stop a Clean Cycle Cleaning OvenHow to Set Oven for Cleaning After Self-Cleaning How to Set Delay Start of CleaningWhy do I have ash left in my oven after cleaning? Operating the Self-Cleaning OvenCan I clean both ovens at the same time? Should there be an odor during the cleaning?Oven Shelves and Convection Roasting Rack Care and CleaningBroiler Pan and Grid Inside of the door Care and CleaningLift-Off Oven Door To remove the doorOven Heating Elements Do not clean the bake element or the broil elementProbe Oven Light BulbCare and Cleaning Problem Solver QUESTIONS? USE this Problem SolverOven will not Work Problem SolverWe’ll Be There Warranty

164D2966P205-1 specifications

The GE 164D2966P205-1 is a versatile and robust component that plays a crucial role in modern industrial applications, particularly within the realm of power generation and distribution. As part of General Electric's extensive product lineup, this component is designed with cutting-edge technologies and features that ensure reliable performance in demanding environments.

One of the main features of the GE 164D2966P205-1 is its high efficiency. This component is engineered to minimize energy loss, enabling systems to operate more effectively while reducing operational costs. This efficiency is complemented by advanced cooling mechanisms, which help manage thermal conditions and prevent overheating during prolonged use.

The GE 164D2966P205-1 incorporates state-of-the-art materials that enhance its durability and longevity. Constructed with high-grade alloys, it is well-suited for extreme environments, including high-temperature and high-pressure conditions. This resilience makes it ideal for industries such as aviation, energy generation, and manufacturing where reliability is paramount.

Another significant characteristic of this component is its compliance with industry standards. GE has designed the 164D2966P205-1 to meet rigorous regulatory requirements, ensuring it is safe and reliable for various applications. This adherence to standards also simplifies integration into existing systems, making it a favored choice among engineers and technicians.

In terms of technology, the GE 164D2966P205-1 utilizes advanced diagnostic features that allow for real-time monitoring and analysis. These features provide users with essential data regarding the component’s performance, facilitating predictive maintenance and reducing the risk of unexpected failures.

Additionally, the modular design of the GE 164D2966P205-1 allows for easy installation and replacement. This feature is particularly beneficial in industrial settings where downtime can result in significant costs. Its compatibility with various platforms enhances its versatility, making it suitable for numerous applications ranging from turbine systems to electrical grids.

In summary, the GE 164D2966P205-1 is a highly efficient, durable, and technologically advanced component that stands out in the competitive landscape of industrial solutions. Its impressive range of features, combined with compliance to industry standards and innovative technologies, makes it a reliable choice for businesses aiming to enhance productivity and reliability in their operations.
Top Page Image Contents