Fisher & Paykel DD607, DD247 Integrated Models, Integrated with Wireless Remote Control

Page 28

4.2.3 Integrated Models

28

4.2.3 Integrated Models

There are 5 user options:

To enter the option mode, check that there is no wash underway, press the power button then open the drawer. Press the Eco button first with one finger, then the Keylock button with another finger, hold both until one long beep sounds, then release the buttons.

You are now in the rinse aid option of the preference options menu., to scroll to the next option push the button.

To change the settings in the option use the Keylock button.

Once the selected option and settings are selected, to save push the Power button. To exit the option at any time push the Power Button.

Option

	Rinse aid	Water softener	Open drawer auto	Beeps at end of wash	Closed drawer
			power-on		autolock

Which option

am I in?

red unlit

green unlit

orange red

green red

red red

Possible settings	1 to 5	0 to 5	On or Off	On or Off	On or Off


GB, IE, EU		On
Secondary
Example
Panel	4 indicators lit = setting is 4	Off

4.2.4 Integrated with Wireless Remote Control

There are 3 user options avialable:

To enter the option mode, make sure no wash is underway and open the drawer.


Press the	button first with one finger, then the button with another finger, hold both until one long beep
sounds, then release the buttons.
You are now in the rinse aid option of the preference options menu.
To change the rinse aid setting press the		button, which will increase or decrease the amount of LED’s on the

secondary control panel, there are 5 dispensing levels (1 LED = approx 0.5mls (1/10 teaspoon) of rinse aid, 5 LED’s = approx. 2.5mls (½ teaspoon) of rinse aid.

To scroll to the next user option press the button

You are now in the water softener water hardness setting of the preference options menu.

To change the settings press button, which will increase or decrease the amount of LED’s showing on the secondary panel.

There are 5 settings available, ensure you set the water softener up depending on the hardness of the incoming water supply.

DishDrawer Settings	Grains per Gallon (gpg)	Parts per Million (ppm)
No LED	0-6	0-100

1 LED	6-14	100-250
2 LED	14-20	250-350

3 LED	20-26	350-450

4 LED	26-32	450-550
5 LED	32-36	550-625

Image 28

Contents Service Manual DishDrawerNZ AU GB IE US CA DD607 & DD247FEATURED PRODUCT & CONTACT ADDRESSES BrandStandard Double Models DescriptionStandard Single Models DD24SCW7Single, Designer, Brushed Stainless Tall Tub Double ModelsTall Tub Single Models DD24SDFTX7Single, Tall Tub, Classic White Single, Tall Tub, Classic, Stainless SteelCONTENTS SERVICE PROCEDURES WIRING DIAGRAMS10 NOTES 1 SERVICE REQUIREMENTS 1.1.1 Electrical Safety1.1.9 Diagnostics 1.1.2 Electrostatic Discharge1.2 Specialised Tools 1.2.1 Static Strap22 15/16 ” 2 DIMENSIONS & SPECIFICATIONS22 15/16” Component Specifications Specification8.0 Ohms per winding, 16 ohms phase to ComponentHall sensor Wash Cycle WashPost TimeDD60 Australia/New Zealand Wash Profiles DD60 United States/Canada Wash ProfilesWash Cycle Wash3 TECHNICAL OVERVIEW 3.3.1 Tub Home Sensor3.3.3 Wireless Remote some integrated models only 3.3.2 Touch Switches3.3.4 Operation some integrated models only 3.3.5 Wireless Receiver Air ValveSluicing Jets 3.4.1 Rotor3.4.3 Filter Plate 3.4.4 Drain Filter3.5.2 During a Power Failure 3.5.1 When Activated3.7.1 Water Inlet 3.7.2 Dispensing Detergent and Rinse Aid 3.7.3 Amount of WaterFlood Sensor 3.7.4 Flood Protection3.8.1 The Heating Element 3.8.2 Heating the Water3.8.3 Maintaining the Temperature 3.8.4 Over Heat ProtectionNon Return Valve 3.11.2 Removing and Cleaning the Drain Filter and Filter Plate 3.11.1 The Filter System3.12.1 Integrated Single Drawer Venting some models only Strainer Spigot Strainer 4 OPTION ADJUSTMENT MODE Not Wireless Model4.1.2 Rinse Aid Setup rA SetupDishDrawer Setting 4.1.3 Water Supply Hardness Setup hdGrains per Gallon Parts per Million4.2.1 Classic Models 4.2.2 Designer Models4.2.3 Integrated Models 4.2.4 Integrated with Wireless Remote Controlbutton, which will increase or decrease the amount of LED’s on the Closed Drawer autolock using the remote control OptionRinse aid Water softener5.1.1 Display Mode 5 DIAGNOSTICS5.1.2 Hardware Output Mode HO Rinse Aid Pump operates as a valve for diagnostic purposes only 5.1.3 Fast Cycle FC 5.1.4 Continuous Cycle Mode CC5.1.6 Show Off/ Showroom Wash Mode 5.1.5 Temperature and Voltage DisplayPlaying Tunes 5.2.1 Diagnostic Mode Program IndicatorsProgram Button 5.2.2 Display Mode5.2.4 Fast Cycle Mode FC 5.2.5 Continous Cycle Mode CC6 FAULT CODES AND POOR PERFORMANCE Fault Code FaultLED Display Possible Causes6.1.1 Sub Code Faults Fast, Delicate Fast & Eco LED’sPoor Dry Performance Non Vented QUESTIONIs the customer complaining of plastic items not drying?How to resolve the problemCustomers Complaint - food particles left on dishes Customers Complaint - coffee/tea stains left in cupswhite chalky film on them More on next pageHow to resolve the problem 7 FAULT FINDING PROCEDURE 7.1 Fault Code Problem SolvingWet E1- Water in the Chassis Base DO NOT REPLACE COMPONENTS ON A TUB WITH THIS WARNINGDry E1 - No Water in the Chassis Base Prefinished models Fault code E2 - Sub Code 03 - Motor Not Drawing Enough Current Controller Harness P201 Corrosion Damage ExampleNOTE For more detailed component testing, refer to page Fault Code E5 - Lid Fault Fault Code E5 - Sub Code 01 - Not StartingFault Code E5 - Sub Code 02 - No Current Fault Code E5 - Sub Code 04 - Not StallingFan Housing Locking Tabs FlapFault Code E7 - Detergent Diverter Valve Fault Code E7 - Sub Code 02 - Under CurrentFault Code E7 - Sub Code 03 - Over Current Detergent Diverter Coil Harness Pin PinWater softener brine pump There are 4 sub codes which relate to this fault code If the problem persists replace the bottom controller 8.2 Power Distribution Concept 8 WIRING DIAGRAMS 8.3 Wiring Diagram Lower Tub Shown Only  9 SERVICE PROCEDURES P204P203 P2021. Open the drawer Clip Cowling Retaining ScrewRail Clip 1. Open the drawer and remove the drawer front refer section 1. Remove the drawer front refert section 1. Remove the cutlery basket and rack from the tub 1. Remove the drawer front refer Section Clips Clips Earth Wire Element CoverDrain Hose Fill Hose 1. Remove the wiring cover refer section 1. Remove the tub as per section Trim Trim ChannelWater Valve Hex Drive Screws Rail Rear Locating TabsClips Inlet Hose Flood Sensor MFB Wiring Harness Link Clip 15mm 3/4” Fill Hoses Water Inlet Hose Chassis Clip9.28 Single Integrated Vent Duct Removal Some models only Trim ClipsT10 Torx Screw Slide Off Tub1. Remove the tub to gain access to the duct, refer section 1. Remove the door panel, refer section Receiver Replacement Procedure Pairing ProcedureTo Pair Remote to Receiver Transmit LED indicator Top Tub start button on doubles 10 NOTES NZ AU GB IE US CA F&P PN 590409 A 11.2011