Fisher & Paykel DD247, DD607 Temperature and Voltage Display, Show Off/ Showroom Wash Mode

Page 33

33

5.1.5 Temperature and Voltage Display

(Not available on integrated or flat door models.)

During a wash cycle, the current water temperature or the power supply rail voltage of the controller can be displayed on the LCD instead of the time remaining.

To enter temperature/voltage display mode, start a wash cycle as normal. Initiate a keylock by pressing and holding the KEYLOCK button for 4 seconds.

Once in keylock mode, press and hold START/PAUSE for 8 seconds to enter temperature display mode. The display now alternates between a oC symbol and the water temperature. Pressing the START/PAUSE button again changes the display to alternate between an oE symbol and the power supply rail voltage of the controller.

To cancel temperature/voltage display mode, press the POWER button.

5.1.6 Show Off/ Showroom Wash Mode

Only available on LCD models only

This mode initiates a shop show off display and wash operation demonstration.

With the DishDrawer™ powered up and turned on, the show off mode is entered by pressing and holding the ECO and POWER buttons simultaneously for 5 seconds. Ensure that ECO is pressed first.

The DishDrawer™ is now in the show off mode and cycles through all of the LED & LCD segments.

Pressing the POWER button now puts the DishDrawer™ into the showroom wash mode. Before running this mode, the tub should be filled with water until it is almost touching the underside of the spray arm. The showroom wash is started by pushing the START/PAUSE button whereby the following cycle is run:-

•The lid is pulled down.

•The wash motor starts and runs for 4 minutes.

•The wash motor stops.

•The lid is lifted.

•The display counts down to zero throughout this cycle.

•The DishDrawer™ turns off at the end of this cycle.

The DishDrawer™ is still in the showroom wash mode however, and it can be re-run by pushing POWER and then START/PAUSE. Once show off/showroom wash mode has been initiated, the mains power supply must be removed to exit out.

Playing Tunes

Once in showroom mode, holding the START/PAUSE button down for 3 seconds will start a tune playing. Pressing the START/PAUSE button again will toggle the tune between Bach and Edvard Grieg’s “Hall of the Mountain King”. This feature is not widely known about, may not be present in all models and may be removed

in future products.

Image 33

Contents DishDrawer Service ManualNZ AU GB IE US CA DD607 & DD247Brand FEATURED PRODUCT & CONTACT ADDRESSESStandard Double Models DescriptionDD24SCW7 Standard Single ModelsSingle, Designer, Brushed Stainless Tall Tub Double ModelsDD24SDFTX7 Tall Tub Single ModelsSingle, Tall Tub, Classic White Single, Tall Tub, Classic, Stainless SteelCONTENTS WIRING DIAGRAMS SERVICE PROCEDURES10 NOTES 1.1.1 Electrical Safety 1 SERVICE REQUIREMENTS1.1.9 Diagnostics 1.1.2 Electrostatic Discharge1.2.1 Static Strap 1.2 Specialised Tools2 DIMENSIONS & SPECIFICATIONS 22 15/16 ”22 15/16” Specification Component Specifications8.0 Ohms per winding, 16 ohms phase to ComponentHall sensor Wash Wash CyclePost TimeDD60 United States/Canada Wash Profiles DD60 Australia/New Zealand Wash ProfilesWash Cycle Wash3.3.1 Tub Home Sensor 3 TECHNICAL OVERVIEW3.3.2 Touch Switches 3.3.3 Wireless Remote some integrated models only3.3.4 Operation some integrated models only Air Valve 3.3.5 Wireless ReceiverSluicing Jets 3.4.1 Rotor3.4.4 Drain Filter 3.4.3 Filter Plate3.5.1 When Activated 3.5.2 During a Power Failure3.7.1 Water Inlet 3.7.3 Amount of Water 3.7.2 Dispensing Detergent and Rinse AidFlood Sensor 3.7.4 Flood Protection3.8.2 Heating the Water 3.8.1 The Heating Element3.8.3 Maintaining the Temperature 3.8.4 Over Heat ProtectionNon Return Valve 3.11.1 The Filter System 3.11.2 Removing and Cleaning the Drain Filter and Filter Plate3.12.1 Integrated Single Drawer Venting some models only Strainer Spigot Strainer Not Wireless Model 4 OPTION ADJUSTMENT MODE4.1.2 Rinse Aid Setup rA Setup4.1.3 Water Supply Hardness Setup hd DishDrawer SettingGrains per Gallon Parts per Million4.2.2 Designer Models 4.2.1 Classic Models4.2.4 Integrated with Wireless Remote Control 4.2.3 Integrated Modelsbutton, which will increase or decrease the amount of LED’s on the Option Closed Drawer autolock using the remote controlRinse aid Water softener5 DIAGNOSTICS 5.1.1 Display Mode5.1.2 Hardware Output Mode HO Rinse Aid Pump operates as a valve for diagnostic purposes only 5.1.4 Continuous Cycle Mode CC 5.1.3 Fast Cycle FC5.1.5 Temperature and Voltage Display 5.1.6 Show Off/ Showroom Wash ModePlaying Tunes Program Indicators 5.2.1 Diagnostic ModeProgram Button 5.2.2 Display Mode5.2.5 Continous Cycle Mode CC 5.2.4 Fast Cycle Mode FC6 FAULT CODES AND POOR PERFORMANCE Fault Fault CodeLED Display Possible Causes6.1.1 Sub Code Faults Fast & Eco LED’s Fast, DelicateQUESTION Poor Dry Performance Non VentedIs the customer complaining of plastic items not drying?problem How to resolve theCustomers Complaint - food particles left on dishes Customers Complaint - coffee/tea stains left in cupsMore on next page white chalky film on themHow to resolve the problem 7.1 Fault Code Problem Solving 7 FAULT FINDING PROCEDUREDO NOT REPLACE COMPONENTS ON A TUB WITH THIS WARNING Wet E1- Water in the Chassis BaseDry E1 - No Water in the Chassis Base Prefinished models Controller Harness P201 Corrosion Damage Example Fault code E2 - Sub Code 03 - Motor Not Drawing Enough CurrentNOTE For more detailed component testing, refer to page Fault Code E5 - Sub Code 01 - Not Starting Fault Code E5 - Lid FaultFault Code E5 - Sub Code 02 - No Current Fault Code E5 - Sub Code 04 - Not StallingFlap Fan Housing Locking TabsFault Code E7 - Sub Code 02 - Under Current Fault Code E7 - Detergent Diverter ValveFault Code E7 - Sub Code 03 - Over Current Detergent Diverter Coil Harness Pin PinWater softener brine pump There are 4 sub codes which relate to this fault code If the problem persists replace the bottom controller 8 WIRING DIAGRAMS 8.2 Power Distribution Concept Lower Tub Shown Only 8.3 Wiring Diagram  P204 9 SERVICE PROCEDURESP203 P2021. Open the drawer Retaining Screw Clip CowlingRail Clip 1. Open the drawer and remove the drawer front refer section 1. Remove the drawer front refert section 1. Remove the cutlery basket and rack from the tub 1. Remove the drawer front refer Section Earth Wire Element Cover Clips ClipsDrain Hose Fill Hose 1. Remove the wiring cover refer section 1. Remove the tub as per section Trim Channel TrimHex Drive Screws Rail Rear Locating Tabs Water ValveClips Inlet Hose Flood Sensor MFB Fill Hoses Water Inlet Hose Chassis Clip Wiring Harness Link Clip 15mm 3/4”Trim Clips 9.28 Single Integrated Vent Duct Removal Some models onlyT10 Torx Screw Slide Off Tub1. Remove the tub to gain access to the duct, refer section 1. Remove the door panel, refer section Pairing Procedure Receiver Replacement ProcedureTo Pair Remote to Receiver Transmit LED indicator Top Tub start button on doubles 10 NOTES 11.2011 NZ AU GB IE US CA F&P PN 590409 A