INSTALLATION REQUIREMENTS
Tools and Parts
Gather the recommended tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.
All Installations
Tools needed:
Pliers |
| |
screwdriver | ||
|
In addition, for first time installations
Tools needed:
Cordless drill |
|
with ¹⁄₂", ³⁄₄" |
|
and 1¹⁄₂" hole | Small |
saw bits | tubing cutter Wire stripper |
Parts needed:
Phillips | Utility knife | |
screwdriver | ||
| ||
nut drivers or | UL Listed/CSA | |
Approved | ||
hex sockets | wire connectors* | |
Measuring tape | Small level | |
or ruler | ||
|
Copper tubing (³⁄₈" O.D. suggested) or flexible braided water supply line
See “Electrical Requirements” section
For Direct Wire: | For Power Supply |
use UL Listed/ | Cord: use UL |
CSA Approved | listed power |
strain relief | supply cord kit |
to fit ⁷⁄₈" (2.2 cm) | marked for use |
hole | with dishwasher |
|
|
10" adjustable wrench |
|
that opens to | wrench |
|
*Must be the proper size to connect your household wiring to 16 gauge wiring in dishwasher
Other useful items you may need:
Flashlight | Bath towel |
Shallow pan | Wood block |
Parts supplied:
Drain hose clamps (2) | Drain hose |
(1 large and 1 small) | |
| screws (2) |
Silver Green
Make sure all these parts are included in the literature package.
Parts needed:
Other parts you may also need:
| Side mounting kit | Masking or |
(38.1– 5 cm) | for solid surface | duct tape |
countertops |
| |
(Part Number |
| |
clamps (3 maximum) |
| |
8212560) |
| |
|
|
NOTE: Parts available for purchase in plumbing supply stores. Check local codes. Check existing electrical supply. See “Electrical Requirements” section. It is recommended that electrical connections be made by a licensed electrical installer.
Teflon is a registered trademark of E.I. Du Pont de Nemours and Company.
Location Requirements
Grounded electrical supply required.
Do not run drain lines, water lines or electrical wiring where they can interfere with or contact dishwasher motor or legs.
The location where the dishwasher will be installed must provide clearance between motor and flooring. Motor should not touch the floor.
Do not install dishwasher over carpeted flooring.
Shelter dishwasher and water lines leading to dishwasher against freezing. Damage from freezing is not covered by the warranty.
A side panel kit is available from your dealer for installing your dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part Number 4396277) is available from your dealer for installing underneath the countertop.
Check location where dishwasher will be installed. The location must provide:
•easy access to water, electricity and drain.
•convenient access for loading and unloading dishes. Corner locations require a 2” (5.1 cm) minimum clearance between the side of the dishwasher door and the wall or cabinet.
•square opening for proper operation and appearance.
•cabinet front perpendicular to floor.
•level floor. (If floor at front of opening is not level with floor at rear of opening, shims may be needed to level dishwasher.)
Helpful Tip: Be sure to accurately measure dimensions and ensure dishwasher is level if the floor in the dishwasher opening is uneven (example: flooring extends only partway into opening).
NOTE: To avoid shifting during dishwasher operation, shims must be securely attached to the floor.
If dishwasher will be left unused for a period of time or in a location where it may be subject to freezing, have it winterized by authorized service personnel.
Make sure pipes, wires and drain hose are within the shaded area shown in the “Product and Cabinet Opening Dimensions” section.
3