Unified Brands HY-6E(CE) Steam Generator and Cooking Chamber, If the Service light stays on

Page 12

6.2.2Steam Generator and Cooking Chamber

The steamer cavity and steam generator may be cleaned separately. When cleaning is scheduled, or if theSERVICE light is on, follow these simple de- liming instructions. REMEMBER: DON’T ALLOW

DE-LIMING AGENTS TO MIX WITH DE- GREASERS.

1.Set the timer to OFF position.

2.Turn off the steamer for five minutes.

3.Open the door and allow the cavity to cool.

4.After the cavity has cooled five minutes, make sure that the fan has stopped and remove the fan baffle partition by lifting it up and toward the center of the cavity.

5.Wipe out the cavity. Make sure the drain holes at the back of the cavity are clear of debris.

6.Hold down the CLEAN button while

turning the steamer on. Continue holding it until the CLEANING

indicator light comes on. Then release the button. After five minutes, the beeper will begin to beep rapidly. This is the signal to

add 500 ml per cavity of Groen De-limer De- Scaler (P/N 114800), Lime-A-Way® or equivalent as shown at right. Do not use any de- limer that contains chlorine.

7.Replace fan baffle partition and close door.

8.The cleaning cycle consists of a boiling clean stage, a soak stage, and a rinse stage. The full cycle takes about 50 minutes to complete.

9.WEAR PROTECTIVE GLOVES AND EYE PROTECTION FOR THIS STEP. When the steamer beeper sounds, turn off the steamer and open the door. After the fan has stopped, remove the fan baffle

partition and rinse it well in a sink. Wipe out the cavity completely. If necessary, use a damp nylon pad.

10.Reinstall the fan baffle.

11.If the steamer will no longer be used, leave it off. Otherwise, wait 10 minutes and turn it back on. When the READY light comes on, the steamer is ready for operation.

6.2.3If the SERVICE light stays on:

1.Check that the water supply is on and that the supply hose is not kinked. With the problem corrected, turn the steamer off or 10 seconds and then re-start.

2.Repeat steam generator cleaning.

The process for de-liming your HY-6E (CE) Steamer is simple, tool-less and quick.

12 OM/SM-HY-6E(CE)

Page 11 Page 13
Image 12
Page 11 Page 13
Contents HY-6ECE Hypersteam Atmospheric Convection Important Read First Important Steam can Cause Burns Table of Contents ReferencesEquipment Description Inspection and UnpackingWater Conditioning Bpst Connection on the right rear side of the steamerInstallation and Start-Up Electrical Supply ConnectionElectrical Supply Connections Water ConnectionsOperating Procedure OperationControls 10 OM/SM-HY-6ECE Cleaning Procedure Outside of SteamerSuggested Tools OM/SM-HY-6ECEIf the Service light stays on Steam Generator and Cooking ChamberMaintenance TroubleshootingParts List External Cabinet and Sheet MetalKey Description 14 OM/SM-HY-6ECECavity Control Section Steamer Base Section 16 OM/SM-HY-6ECESteamer Base Rear View Steamer Motor and Controls 18 OM/SM-HY-6ECESteamer Generator Individual Parts Key Description NewSteamer Individual Parts 20 OM/SM-HY-6ECEService Information Adjustable Legs P/NTop Right Side Panel Louvered Removal P/N 10.3 Top/Left Side Removal P/NTo Test Water Inlet Valve Three Way P/NWater Inlet Valve Coil Drain Box Spray Nozzle P/NTo Install Heater Assembly Complete with High Limit ThermostatSteam Generator P/N Steam Generator Probes High and Low Water P/NTo Prepare 24 OM/SM-HY-6ECETimer Assembly Timer Fastener Nut Control Voltage Transformer P/NElectrical Contactor Fan Motor Assembly Motor Insulation Motor Shaft Seal To Install a New Motor10.17 Fan 26 OM/SM-HY-6ECETo Install New Capacitor Motor Starting Capacitor P/NSteam Generator Ready Thermostat P/N Steam Port GasketDoor Removal/Installation/Alignment P/N Door Switch P/NDoor Reversing Procedures To AlignDoor Handle, Magnet and Block Assembly Door Gasket P/NDoor Spring P/N Door Locking Pin P/N Lock Nut P/N30 OM/SM-HY-6ECE Electrical Schematic Service Log 32 OM/SM-HY-6ECELimited Warranty To Commercial Purchasers Part Number 128717, REV. B 4/06

HY-6E(CE) specifications

Unified Brands HY-6E(CE) is a state-of-the-art cooking appliance specifically designed for professional kitchens, providing top-notch technology, efficiency, and capability. This equipment stands out due to its combination of advanced features and user-friendly controls, making it an ideal choice for restaurants, catering services, and foodservice operations.

One of the most notable features of the HY-6E(CE) is its powerful heating system, which allows for rapid cooking times and consistent results. The unit is equipped with a high-efficiency burner system that ensures even heat distribution while minimizing energy consumption. This innovative technology not only enhances cooking performance but also contributes to cost savings in energy usage.

Another significant characteristic of the HY-6E(CE) is its versatility. The appliance supports various cooking methods, including boiling, frying, steaming, and simmering, making it suitable for a wide range of culinary applications. This adaptability enables chefs to prepare multiple dishes simultaneously, thereby increasing kitchen productivity.

The design of the HY-6E(CE) emphasizes durability and ease of maintenance. Constructed from high-grade stainless steel, it is built to withstand the rigors of a busy kitchen while resisting corrosion and wear. The smooth surfaces and streamlined design facilitate quick cleaning, ensuring that hygiene standards are upheld without excessive downtime.

In terms of control and monitoring, the HY-6E(CE) features an intuitive digital interface that allows chefs to set precise temperature and timing. This level of control is crucial for maintaining culinary consistency and quality, especially in high-pressure environments. The appliance also includes safety features such as automatic shut-off and flame failure protection, ensuring a safe cooking experience.

The HY-6E(CE) is further enhanced with smart technology options that enable remote monitoring and adjustments via mobile applications. This connectivity allows operators to oversee kitchen operations from any location, optimizing workflow and ensuring that meal preparation runs smoothly.

In conclusion, the Unified Brands HY-6E(CE) is an exemplary cooking appliance that merges efficiency, versatility, and advanced technology. Its features cater to the dynamic needs of the modern kitchen, making it a valuable addition for culinary professionals who prioritize performance and reliability in their cooking operations.
Top Page Image Contents