Unified Brands HY-6E(CE) service manual Control Voltage Transformer P/N, Electrical Contactor

Page 25

10.13Supply Voltage Terminal Block - P/N 096810 Fuse - P/N 096809

Fuse 20 Amp - P/N 071489

1.Turn off the power to the steamer.

2.Remove the cover from the electrical compartment.

3.The terminal block is located on the back wall of the electrical compartment.

4.Using a flat blade screwdriver, disconnect the incoming wires from the top of the terminal block and the steamer wires from the lower portion of the terminal block.

5.With a wrench, remove the four 8-32 screws holding the terminal block to the back wall.

To Install:

6.Position the new terminal block on the back wall and install the four 8-32 screws using a wrench.

7.Using a flat blade screwdriver, connect the incoming wires to the top of the terminal block, and the steamer wires to the lower portion of the terminal block.

10.14Control Voltage Transformer P/N 121716

1.Turn off power to the steamer.

2.Remove the front lower panel.

3.Using an open ended wrench, remove the four 1/4-20 bolts holding the electrical compartment to the steamer table.

4.Disconnect the line side and the load side of the electrical wires from their respective terminals.

5.Using a socket wrench with an extension, remove the four 8-32 hex nut screws holding the transformer to the floor of the electrical compartment.

To Install:

6.Position the transformer in the electrical compartment.

7.Using a socket wrench with an extension, insert and tighten the four 8-32 hex nut screws.

8.Connect the load and line side terminals.

10.15Electrical Contactor

P/N 119811

1.Turn off power to the steamer.

2.Remove the front lower panel.

3.Using an open ended wrench, remove the four 1/4 - 20 bolts holding the electrical contactor to the electrical compartment.

4.Unplug the line side and the load side terminals of the contactor. Disconnect the control wires to the contactor.

5.Using a socket wrench and extension, remove the four 8-32 hex nut screws holding the contactor to the floor of the electrical compartment.

To Install:

6.Position the contactor in the electrical compartment.

7.Using a socket wrench and extension, insert and tighten the four 8-32 hex nut screws.

NOTE: The space is very restricted and it is helpful if the nutdriver has a magnetic head to hold the screw in position while it is being started.

8.Connect the load and line side terminals and the control wires.

NOTE. The following components and subassemblies are to be found in the upper portion of the steamer.

10.16 Timer Assembly

Timer Fastener Nut

P/N 100983

P/N 101145

1.Remove the four hex nuts which retain the control panel cover. Remove the cover.

2.Remove the knob from the timer. Under the knob is a hexagonal nut which holds the time mechanism to the steamer. Note that there is a flat on the timer shaft which corresponds to a frictional mounting hole on the knob.

3.From the left side, unplug the five terminals/wires (violet, gray, black, tan and white) from the timer mechanism and unplug the two black timer motor leads.

4.With an open-ended wrench, remove the hex nut holding the timer in place. The timer may then be removed from inside the compartment.

5.NOTE: Right below the timer shaft, the timer has a small plastic disk molded onto the case. There is a

OM/SM-HY-6E(CE) 25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents HY-6ECE Hypersteam Atmospheric Convection Important Read First Important Steam can Cause Burns References Table of ContentsInspection and Unpacking Equipment DescriptionBpst Connection on the right rear side of the steamer Water ConditioningElectrical Supply Connection Installation and Start-UpWater Connections Electrical Supply ConnectionsOperation Operating ProcedureControls 10 OM/SM-HY-6ECE Procedure Outside of Steamer CleaningSuggested Tools OM/SM-HY-6ECESteam Generator and Cooking Chamber If the Service light stays onTroubleshooting MaintenanceExternal Cabinet and Sheet Metal Parts ListKey Description 14 OM/SM-HY-6ECECavity Control Section 16 OM/SM-HY-6ECE Steamer Base SectionSteamer Base Rear View 18 OM/SM-HY-6ECE Steamer Motor and ControlsKey Description New Steamer Generator Individual Parts20 OM/SM-HY-6ECE Steamer Individual PartsAdjustable Legs P/N Service InformationTop Right Side Panel Louvered Removal P/N 10.3 Top/Left Side Removal P/NWater Inlet Valve Three Way P/N To TestWater Inlet Valve Coil Drain Box Spray Nozzle P/NHeater Assembly Complete with High Limit Thermostat To InstallSteam Generator P/N Steam Generator Probes High and Low Water P/N24 OM/SM-HY-6ECE To PrepareControl Voltage Transformer P/N Timer Assembly Timer Fastener NutElectrical Contactor To Install a New Motor Fan Motor Assembly Motor Insulation Motor Shaft Seal10.17 Fan 26 OM/SM-HY-6ECEMotor Starting Capacitor P/N To Install New CapacitorSteam Generator Ready Thermostat P/N Steam Port GasketDoor Switch P/N Door Removal/Installation/Alignment P/NDoor Reversing Procedures To AlignDoor Gasket P/N Door Handle, Magnet and Block AssemblyDoor Locking Pin P/N Lock Nut P/N Door Spring P/N30 OM/SM-HY-6ECE Electrical Schematic 32 OM/SM-HY-6ECE Service LogLimited Warranty To Commercial Purchasers Part Number 128717, REV. B 4/06

HY-6E(CE) specifications

Unified Brands HY-6E(CE) is a state-of-the-art cooking appliance specifically designed for professional kitchens, providing top-notch technology, efficiency, and capability. This equipment stands out due to its combination of advanced features and user-friendly controls, making it an ideal choice for restaurants, catering services, and foodservice operations.

One of the most notable features of the HY-6E(CE) is its powerful heating system, which allows for rapid cooking times and consistent results. The unit is equipped with a high-efficiency burner system that ensures even heat distribution while minimizing energy consumption. This innovative technology not only enhances cooking performance but also contributes to cost savings in energy usage.

Another significant characteristic of the HY-6E(CE) is its versatility. The appliance supports various cooking methods, including boiling, frying, steaming, and simmering, making it suitable for a wide range of culinary applications. This adaptability enables chefs to prepare multiple dishes simultaneously, thereby increasing kitchen productivity.

The design of the HY-6E(CE) emphasizes durability and ease of maintenance. Constructed from high-grade stainless steel, it is built to withstand the rigors of a busy kitchen while resisting corrosion and wear. The smooth surfaces and streamlined design facilitate quick cleaning, ensuring that hygiene standards are upheld without excessive downtime.

In terms of control and monitoring, the HY-6E(CE) features an intuitive digital interface that allows chefs to set precise temperature and timing. This level of control is crucial for maintaining culinary consistency and quality, especially in high-pressure environments. The appliance also includes safety features such as automatic shut-off and flame failure protection, ensuring a safe cooking experience.

The HY-6E(CE) is further enhanced with smart technology options that enable remote monitoring and adjustments via mobile applications. This connectivity allows operators to oversee kitchen operations from any location, optimizing workflow and ensuring that meal preparation runs smoothly.

In conclusion, the Unified Brands HY-6E(CE) is an exemplary cooking appliance that merges efficiency, versatility, and advanced technology. Its features cater to the dynamic needs of the modern kitchen, making it a valuable addition for culinary professionals who prioritize performance and reliability in their cooking operations.
Top Page Image Contents