Sub-Zero ICB700TR T E G R AT E D Installation Instructions Accessories, S I T I O N the Unit

Page 14

I N T E G R AT E D INSTALLATION INSTRUCTIONS

ACCESSORIES

Optional acces- sories are available through your Sub-Zero dealer. To obtain local dealer information, visit our website, subzero.com.

A N T I - T I P BLOCKING BRACKET

INSTALL CONCRETE WEDGE ANCHORS

1)Drill a 10 mm diameter hole any depth exceeding the minimum embedment. Clean the hole or continue drilling additional depth to accommodate drill fines. Use a carbide drill bit.

2)Assemble the washer and nut flush with the end of anchor to protect threads. Drive the anchor through the material to be fastened until the washer is flush with the surface material.

3)Expand the anchor by tightening the nut 3–5 turns past hand-tight position or to 25 foot-pounds (34N) of torque.

Always wear safety glasses and use other necessary protective devices or apparel when installing or working with anchors.

Anchors are not recommended for use in lightweight masonry material such as block or brick, or for use in new concrete which has not had sufficient time to cure. The use of core drills is not recommended to drill holes for the anchors.

P O S I T I O N THE UNIT

Before moving the Integrated unit into position, secure the door closed and remove the drawers.

IMPORTANT NOTE: On base units, the top drawer has a control cable that needs to be disconnected before removing this drawer.

Refer to illustration 3 below for placement and how to disconnect this fitting.

The drawers should be placed aside until you are ready for installation of the panels. Remove the decorative top and side molding pieces and the kickplate/grille.

IMPORTANT NOTE: If two Integrated units are installed closer than 51 mm to one another, it is necessary to use the Sub-Zero dual installa- tion heater kit (ICBTTDUAL). Refer to Dual Installations on page 21 for additional informa- tion. The heater plate from this kit must be attached to the left side exterior of the right hand unit before the units are slid into position.

Illus. 3

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Integrated Refrigeration Page G L I S H P Ã N O L A N Ç a I S TA L I a N O U T S C H N T E N T S Tools and Materials Required T E G R AT E D Installation RecommendationsS TA L L AT I O N Recommendations Site PreparationWidth 686 mm Height 2032 mm Depth 635 mm T E G R AT E D Installation SpecificationsWidth 686 mm Height 2032 mm Depth 610 mm Width 914 mm Height 2032 mm Depth 635 mm Width 914 mmHeight 2032 mm Depth 610 mm Width 686 mm Height 876 mm Depth 610 mm Width 686 mm Height 876 mm Depth 635 mmT E G R AT E D Installation Instructions E C T R I C a L RequirementsT E G R AT E D Installation Specifications Accessories LU M B I N G RequirementsDoor and Drawer Panels Side Panels Panel DesignT E G R AT E D Installation Instructions Wood Floor Applications Concrete Floor Applications Mm Wide Units 343 mm 457 mmT I T I P Blocking Bracket T E G R AT E D Installation Instructions AccessoriesInstall Concrete Wedge Anchors S I T I O N the UnitS I T I on the Unit V E L the Unit L D I N G I N S TA L L AT I O N Quick Connect Water Valve PA N E L I N S TA L L AT I O N T E G R AT E D Installation Instructions Panel RequirementsC K P L AT E / G R I L L E Installation Door Panel Installation Protected surface to ensure that the front is notPA N E L Installation Drawer Panel InstallationUA L I N S TA L L AT I O N S E G R E E Door StopInstallation Checklist S TA L L AT I O N C H E C K L I S TR V I C E I N F O R M AT I O N N TAC T F O R M AT I O ND I C E Necesarios Recomendaciones DE Instalación I N T E G R a B L EHerramientas Y Materiales Fondo 610 mm Especificaciones DE Instalación I N T E G R a B L EAnchura 686 mm Altura 032 mm Anchura 686 mm Altura 032 mm Fondo 635 mmAnchura 914 mm Altura 032 mm Fondo 610 mm Altura 032 mm Fondo 635 mmAnchura 686 mm Altura 876 mm Fondo 610 mm Anchura 686 mm Altura 876 mm Fondo 635 mmInstrucciones DE Instalación I N T E G R a B L E Requisitos E L É C T R I C O SRequisitos DE F O N T a N E R Í a Paneles DE LA Puerta Y LOS Paneles Laterales Cajones Diseño DEL PanelInstalación DEL S O P O RT E E N to T I V U E LCOAplicaciones EN Suelo DE Madera Hormigón T I V U E LC O Instrucciones DE Instalación I N T E G R a B L E AccesoriosSoporte DE Bloqueo Instalación DE Anclajes DE Expansión Para HormigónNivele la unidad antes de desplazarla para colo V E L a C I Ó N DE LA Unidad Instalación DE LA M O L D U R a Conexión a LA to M a D E a G UA Válvula DE Agua DE Conexión RápidaInstalación DEL Z Ó C a LO / R E J I L L a Instalación DEL PA N E LInstalación DEL Panel DE LA Puerta Instalación DE LOS Paneles DE LOS Cajones Tope DE Puerta a 9 0 G R a D O S S TA L a C I Ó N S TA D E CO M P R O BA C I Ó N DE LA InstalaciónLista DE Comprobación DE LA Lista DE Comprobación DE LAM I E N to Información Sobre EL M a N T E N I M I E N toInformación Sobre EL M a N T E Información DE ContactoTable DES Matieres Outils ET Materiaux Requis T E G R a B L E S Recommandations D’INSTALLATIONPreparation DE L’EMPLACEMENT Profondeur 610 mm T E G R a B L E S Specifications D’INSTALLATIONLargeur 686 mm Hauteur 032 mm Profondeur 635 mmLargeur 914 mm Hauteur 032 mm Profondeur 610 mm Largeur 914 mm Hauteur 032 mm Profondeur 635 mmLargeur 686 mm Hauteur 876 mm Profondeur 610 mm Largeur 686 mm Hauteur 876 mm Profondeur 635 mmT E G R a B L E S Instructions D’INSTALLATION Configuration E L E C T R I Q U ET E G R a B L E S Specifications D’INSTALLATION Accessoires Configuration DE LA P L O M B E R I EPanneaux DE Porte ET DE Tiroir Panneaux Lateraux Modeles DE PanneauxT I B a S C U L E M E N T Installation DU SupportB a L L a G E ET D E P L a C E M E N T D E ’ a P PA R E I L SUR UN Plancher DE Bois SUR UN SOL EN BetonSupport a N T I B a S C U L E M E N T T E G R a B L E S Instructions D’INSTALLATION AccessoiresInstallation DES Ancrages a Cale Pour SOL EN Beton S E E N P L a C E DE L’APPAREILRemarque Importante Une fois l’appareil S E a N I V E AU DE L’APPAREIL Robinet DE Prise D’EAU a Raccord RapideInstallation DE L a P L I N T H E I L L E Pose DES P a N N E a UPose DES Panneaux DE Porte Remarque Importante Le gabaritPose DE Panneau DE Tiroir Installations C O N J O I N T E S R E T D E P O RT E a 90 DegresListe DE Controle S T E D E CO N T R O L E DE L’INSTALLATION’INSTALLATION Liste DE Controle DEN TAC T SUB-ZEROè un marchio depositato Sub-Zero, Inc Preparazione DEL Sito Consigli PER L’INSTALLAZIONE I N T E G R a T aAttrezzi E Materiale Richiesti Specifiche PER L’INSTALLAZIONE I N T E G R a T a Larghezza 686 mm Altezza 032 mm Profondità 635 mmAltezza 032 mm Profondità 610 mm Larghezza 914 mm Altezza 032 mm Profondità 635 mmLarghezza 686 mm Altezza 876 mm Profondità 610 mm Larghezza 686 mm Altezza 876 mm Profondità 635 mmIstruzioni PER L’INSTALLAZIONE I N T E G R a T a Collegamento E L E T T R I C OSpecifiche PER L’INSTALLAZIONE I N T E G R a T a Accessori Collegamento I D R I C OPannelli PER Porte E Cassetti Pannelli Laterali Design DEI PannelliT I R I B a L T a M E N T O Applicazione PER Pavimenti Legno Cemento Barra DI Blocco a N T I R I B a L T a N T O Istruzioni PER L’INSTALLAZIONE I N T E G R a T a AccessoriInstallazione DEI Tasselli PER Cemento S I Z I O N a M E N to DELL’UNITÀIstruzioni PER L’INSTALLAZIONE I N T E G R ATA Modanatura superiore Collegamento Rapido Della Valvola IdricaInstallazione D I Z O CCO LO I G L I a Installazione D E I PA N N E L LInstallazione DEL Pannello Della Porta Installazione DEI Pannelli PER Cassetti Installazioni D U a L R M a P O RTA DA 90 GradiCheck List PER L ’ Install a Z I O N E Check List PER L’INSTALLAZIONES I S T E N Z a Informazioni PER IL S E R V I Z I O D I a S S I S T E N Z aInformazioni PER IL S E R V I Z I O D Informazioni PER I ContattiVorsicht Empfehlungen ZUR Installation Gesamtabmessungen Breite 914 mm Höhe 032 mm Tiefe 610 mm 229 E K T R O V O R a U S S E T Z U N G E N VO R AU S S E T Z U N G E N FÜR DIE KO R P L AT T E N Um ein Abkippen des Geräts nach vorne zu H U T Z H a L T E R U N G S I T I O N I E R E N DES Geräts Stromzufuhr zur Steckdose unterbrechen Obere Leiste Anschluss DER WA S S E R L E I T U N G C K E L L E I S T E / G I T T E R Installation DER Türplatte 100 101 S TA L L AT I O N S C H E C K L I S T E R V I C E I N F O R M AT I O N E N SUB-ZERO, INC

ICB700TR, ICB700TCI, ICB700TFI specifications

The Sub-Zero ICB700 series comprises three impressive models: ICB700TFI, ICB700TCI, and ICB700TR. Renowned for their commitment to quality and innovation, Sub-Zero has designed these integrated column refrigerators to cater to the discerning needs of culinary enthusiasts and professionals alike.

One of the standout features of the ICB700 series is its seamless integration capabilities. With a panel-ready design, these refrigerators can be customized to match existing cabinetry, providing a stunning aesthetic that complements any kitchen layout. This attention to design details ensures that the refrigerators blend effortlessly into their surroundings while offering advanced functionality.

At the heart of the ICB700 series is the Purity technology, which includes an advanced air purification system. This system utilizes a carbon filter to remove ethylene gas, a common agent that accelerates food spoilage. By maintaining optimal air quality within the refrigerator, the Purity system extends the freshness of fruits and vegetables, ensuring that your ingredients remain at their peak for longer periods.

Each model in the ICB700 series is equipped with an advanced cooling system that employs dual-compressor technology. This feature allows for separate temperature control of the refrigerator and freezer compartments. Consequently, it ensures that air circulates uniformly, minimizing temperature fluctuations and preserving the quality of stored food items.

The interior of each ICB700 model is thoughtfully designed for convenience and functionality. Adjustable glass shelves provide flexible storage options, while the soft-close drawers offer easy access to both fresh and frozen items. The organization drawers keep your food neatly in place, allowing for quick identification and access.

Another key feature is the Smart Touch Control panel, which allows users to easily set temperatures and monitor performance. With intuitive controls, users can quickly adjust settings according to their needs, ensuring optimal storage conditions for various food items.

Energy efficiency is also a hallmark of the ICB700 series. These refrigerators are designed to utilize less energy while delivering powerful refrigeration performance, making them a responsible choice for environmentally-conscious consumers.

In summary, the Sub-Zero ICB700TFI, ICB700TCI, and ICB700TR models combine a sleek, integrated design with cutting-edge technologies. Their superior air purification, adjustable interior, advanced cooling systems, and user-friendly controls make them an ideal choice for anyone looking to elevate their culinary experience. This series exemplifies Sub-Zero’s commitment to quality and performance, making it a reliable addition to any kitchen.
Top Page Image Contents