Sub-Zero ICB700TR, ICB700TFI, ICB700TCI PA N E L Installation, Drawer Panel Installation

Page 20

I N T E G R AT E D INSTALLATION INSTRUCTIONS

PANEL REQUIREMENTS

Door and drawer panels must be a minimum of 16 mm thick.

The door panel cannot exceed 18 kg and each drawer panel must not exceed 5 kg for 686

mmwide units. For

914 mm wide units, the door panel weight limit is 24 kg and 7 kg for each drawer panel.

PA N E L INSTALLATION

Before attaching the door panel to the door, place two screws in the center of each mounting position, just enough that the slotted holes on the hinge side door panel bracket will slide under the heads. These positioning screws will support the door panel during installation and adjustment. Refer to illustra- tion 14 below.

Install the door panel by engaging the tabbed bracket to the handle side of the door first and then sliding the hinge side mounting bracket onto the positioning screws on the hinge side of the door. The panel can be adjusted 6 mm up and down and side to side.

Once the door panel is in place and adjusted correctly, attach the six remaining #10 x 12,7

mmscrews to the hinge side mounting bracket and install the magnetic decorative caps as shown in illustration 14.

As the reveal between cabinets and the unit decreases, the potential exists for severe finger pinching if fingers are placed in the opening when the door is closing.

DRAWER PANEL INSTALLATION

Remove the mounting hardware provided and set aside. As with the door panel, you should work on the back side of each drawer panel and protect the fronts of these panels.

Position the top edge of the template flush with the top edge of each drawer. For the top drawer, there is only one location for the lower mounting bracket to be placed. However, the bottom drawer allows a second option, invert- ing the lower mounting bracket, depending on the height and thickness or detail of the panel. Refer to illustration 15 below.

Secure the template in place with tape or a small clamp and mark positions for the pilot holes. Remove the template and drill the pilot holes. Place the mounting brackets in the proper location with the tabbed bracket on top and ’L’ bracket on the bottom of the panel. Fasten brackets securely with the #8 x 12,7

mmscrews provided. Refer to illustration 16 below. Illustration 13 on page 17 also shows the mounting hardware location for drawer panels.

Top Of Template

Flush With Top Of

Drawer Panel

 

 

Gap On Side

 

 

Edges Will Vary

 

 

According To

 

 

Design

 

 

Back Of

 

 

Drawer Panel

Illus. 14

Illus. 15

Illus. 16

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Integrated Refrigeration Page G L I S H P Ã N O L A N Ç a I S TA L I a N O U T S C H N T E N T S T E G R AT E D Installation Recommendations S TA L L AT I O N RecommendationsTools and Materials Required Site PreparationWidth 686 mm Height 2032 mm Depth 635 mm T E G R AT E D Installation SpecificationsWidth 686 mm Height 2032 mm Depth 610 mm Width 914 mm Height 2032 mm Depth 635 mm Width 914 mmHeight 2032 mm Depth 610 mm Width 686 mm Height 876 mm Depth 610 mm Width 686 mm Height 876 mm Depth 635 mmT E G R AT E D Installation Instructions E C T R I C a L RequirementsT E G R AT E D Installation Specifications Accessories LU M B I N G RequirementsDoor and Drawer Panels Side Panels Panel DesignT E G R AT E D Installation Instructions Wood Floor Applications Concrete Floor Applications Mm Wide Units 343 mm 457 mmT E G R AT E D Installation Instructions Accessories Install Concrete Wedge AnchorsT I T I P Blocking Bracket S I T I O N the UnitS I T I on the Unit V E L the Unit L D I N G I N S TA L L AT I O N Quick Connect Water Valve PA N E L I N S TA L L AT I O N T E G R AT E D Installation Instructions Panel RequirementsC K P L AT E / G R I L L E Installation Door Panel Installation Protected surface to ensure that the front is notPA N E L Installation Drawer Panel InstallationUA L I N S TA L L AT I O N S E G R E E Door StopInstallation Checklist S TA L L AT I O N C H E C K L I S TR V I C E I N F O R M AT I O N N TAC T F O R M AT I O ND I C E Necesarios Recomendaciones DE Instalación I N T E G R a B L EHerramientas Y Materiales Especificaciones DE Instalación I N T E G R a B L E Anchura 686 mm Altura 032 mmFondo 610 mm Anchura 686 mm Altura 032 mm Fondo 635 mmAnchura 914 mm Altura 032 mm Fondo 610 mm Altura 032 mm Fondo 635 mmAnchura 686 mm Altura 876 mm Fondo 610 mm Anchura 686 mm Altura 876 mm Fondo 635 mmInstrucciones DE Instalación I N T E G R a B L E Requisitos E L É C T R I C O SRequisitos DE F O N T a N E R Í a Paneles DE LA Puerta Y LOS Paneles Laterales Cajones Diseño DEL PanelInstalación DEL S O P O RT E E N to T I V U E LCOAplicaciones EN Suelo DE Madera Hormigón Instrucciones DE Instalación I N T E G R a B L E Accesorios Soporte DE BloqueoT I V U E LC O Instalación DE Anclajes DE Expansión Para HormigónNivele la unidad antes de desplazarla para colo V E L a C I Ó N DE LA Unidad Instalación DE LA M O L D U R a Conexión a LA to M a D E a G UA Válvula DE Agua DE Conexión RápidaInstalación DEL Z Ó C a LO / R E J I L L a Instalación DEL PA N E LInstalación DEL Panel DE LA Puerta Instalación DE LOS Paneles DE LOS Cajones Tope DE Puerta a 9 0 G R a D O S S TA D E CO M P R O BA C I Ó N DE LA Instalación Lista DE Comprobación DE LAS TA L a C I Ó N Lista DE Comprobación DE LAInformación Sobre EL M a N T E N I M I E N to Información Sobre EL M a N T EM I E N to Información DE ContactoTable DES Matieres Outils ET Materiaux Requis T E G R a B L E S Recommandations D’INSTALLATIONPreparation DE L’EMPLACEMENT T E G R a B L E S Specifications D’INSTALLATION Largeur 686 mm Hauteur 032 mmProfondeur 610 mm Profondeur 635 mmLargeur 914 mm Hauteur 032 mm Profondeur 610 mm Largeur 914 mm Hauteur 032 mm Profondeur 635 mmLargeur 686 mm Hauteur 876 mm Profondeur 610 mm Largeur 686 mm Hauteur 876 mm Profondeur 635 mmT E G R a B L E S Instructions D’INSTALLATION Configuration E L E C T R I Q U ET E G R a B L E S Specifications D’INSTALLATION Accessoires Configuration DE LA P L O M B E R I EPanneaux DE Porte ET DE Tiroir Panneaux Lateraux Modeles DE PanneauxT I B a S C U L E M E N T Installation DU SupportB a L L a G E ET D E P L a C E M E N T D E ’ a P PA R E I L SUR UN Plancher DE Bois SUR UN SOL EN BetonT E G R a B L E S Instructions D’INSTALLATION Accessoires Installation DES Ancrages a Cale Pour SOL EN BetonSupport a N T I B a S C U L E M E N T S E E N P L a C E DE L’APPAREILRemarque Importante Une fois l’appareil S E a N I V E AU DE L’APPAREIL Robinet DE Prise D’EAU a Raccord RapideInstallation DE L a P L I N T H E I L L E Pose DES P a N N E a UPose DES Panneaux DE Porte Remarque Importante Le gabaritPose DE Panneau DE Tiroir Installations C O N J O I N T E S R E T D E P O RT E a 90 DegresS T E D E CO N T R O L E DE L’INSTALLATION ’INSTALLATIONListe DE Controle Liste DE Controle DEN TAC T SUB-ZEROè un marchio depositato Sub-Zero, Inc Preparazione DEL Sito Consigli PER L’INSTALLAZIONE I N T E G R a T aAttrezzi E Materiale Richiesti Specifiche PER L’INSTALLAZIONE I N T E G R a T a Larghezza 686 mm Altezza 032 mm Profondità 635 mmAltezza 032 mm Profondità 610 mm Larghezza 914 mm Altezza 032 mm Profondità 635 mmLarghezza 686 mm Altezza 876 mm Profondità 610 mm Larghezza 686 mm Altezza 876 mm Profondità 635 mmIstruzioni PER L’INSTALLAZIONE I N T E G R a T a Collegamento E L E T T R I C OSpecifiche PER L’INSTALLAZIONE I N T E G R a T a Accessori Collegamento I D R I C OPannelli PER Porte E Cassetti Pannelli Laterali Design DEI PannelliT I R I B a L T a M E N T O Applicazione PER Pavimenti Legno Cemento Istruzioni PER L’INSTALLAZIONE I N T E G R a T a Accessori Installazione DEI Tasselli PER CementoBarra DI Blocco a N T I R I B a L T a N T O S I Z I O N a M E N to DELL’UNITÀIstruzioni PER L’INSTALLAZIONE I N T E G R ATA Modanatura superiore Collegamento Rapido Della Valvola IdricaInstallazione D I Z O CCO LO I G L I a Installazione D E I PA N N E L LInstallazione DEL Pannello Della Porta Installazione DEI Pannelli PER Cassetti Installazioni D U a L R M a P O RTA DA 90 GradiCheck List PER L ’ Install a Z I O N E Check List PER L’INSTALLAZIONEInformazioni PER IL S E R V I Z I O D I a S S I S T E N Z a Informazioni PER IL S E R V I Z I O DS I S T E N Z a Informazioni PER I ContattiVorsicht Empfehlungen ZUR Installation Gesamtabmessungen Breite 914 mm Höhe 032 mm Tiefe 610 mm 229 E K T R O V O R a U S S E T Z U N G E N VO R AU S S E T Z U N G E N FÜR DIE KO R P L AT T E N Um ein Abkippen des Geräts nach vorne zu H U T Z H a L T E R U N G S I T I O N I E R E N DES Geräts Stromzufuhr zur Steckdose unterbrechen Obere Leiste Anschluss DER WA S S E R L E I T U N G C K E L L E I S T E / G I T T E R Installation DER Türplatte 100 101 S TA L L AT I O N S C H E C K L I S T E R V I C E I N F O R M AT I O N E N SUB-ZERO, INC

ICB700TR, ICB700TCI, ICB700TFI specifications

The Sub-Zero ICB700 series comprises three impressive models: ICB700TFI, ICB700TCI, and ICB700TR. Renowned for their commitment to quality and innovation, Sub-Zero has designed these integrated column refrigerators to cater to the discerning needs of culinary enthusiasts and professionals alike.

One of the standout features of the ICB700 series is its seamless integration capabilities. With a panel-ready design, these refrigerators can be customized to match existing cabinetry, providing a stunning aesthetic that complements any kitchen layout. This attention to design details ensures that the refrigerators blend effortlessly into their surroundings while offering advanced functionality.

At the heart of the ICB700 series is the Purity technology, which includes an advanced air purification system. This system utilizes a carbon filter to remove ethylene gas, a common agent that accelerates food spoilage. By maintaining optimal air quality within the refrigerator, the Purity system extends the freshness of fruits and vegetables, ensuring that your ingredients remain at their peak for longer periods.

Each model in the ICB700 series is equipped with an advanced cooling system that employs dual-compressor technology. This feature allows for separate temperature control of the refrigerator and freezer compartments. Consequently, it ensures that air circulates uniformly, minimizing temperature fluctuations and preserving the quality of stored food items.

The interior of each ICB700 model is thoughtfully designed for convenience and functionality. Adjustable glass shelves provide flexible storage options, while the soft-close drawers offer easy access to both fresh and frozen items. The organization drawers keep your food neatly in place, allowing for quick identification and access.

Another key feature is the Smart Touch Control panel, which allows users to easily set temperatures and monitor performance. With intuitive controls, users can quickly adjust settings according to their needs, ensuring optimal storage conditions for various food items.

Energy efficiency is also a hallmark of the ICB700 series. These refrigerators are designed to utilize less energy while delivering powerful refrigeration performance, making them a responsible choice for environmentally-conscious consumers.

In summary, the Sub-Zero ICB700TFI, ICB700TCI, and ICB700TR models combine a sleek, integrated design with cutting-edge technologies. Their superior air purification, adjustable interior, advanced cooling systems, and user-friendly controls make them an ideal choice for anyone looking to elevate their culinary experience. This series exemplifies Sub-Zero’s commitment to quality and performance, making it a reliable addition to any kitchen.
Top Page Image Contents