Cornelius 2232MS service manual Always Install NEW Ball Seat Quadding P/N

Page 26

2.Close Beverage Control Panel Assembly water inlet supply line shutoff valve.

3.Loosen screen retainer, then pull screen retainer and strainer screen from water pump. (see Figure 12).

4.Pull strainer screen from screen retainer. Clean any sediment from screen retainer and pump screen retainer port.

WATER PUMP

WATER

STRAINER SCREEN

(P/N 315348–000)

O–RING

(P/N 315349–000)

SCREEN RETAINER

FIGURE 12. WATER STRAINER SCREEN

5.Inspect strainer screen for holes, restrictions, corrosion, and other damage. Discard damaged strainer screen.

6.Check O–Ring on screen retainer. Replace worn or damaged O–Ring (P/N 315349–000).

NOTE: A strainer screen should always be used, otherwise particles could foul liquid check valve.

7.Install good or new strainer screen (P/N 315348–000) in screen retainer, then screw retainer into water pump and tighten securely.

8.Service liquid check valve (refer to next paragraph, Servicing Liquid Check Valve).

Servicing Liquid Check Valve

1.Service water pump water strainer screen as instructed in previous paragraph, Servicing Water In let Strainer Screen; before servicing liquid check valve.

2.Disconnect pressure switch (see Figure 13) from liquid check valve assembly outlet, then remove check valve from water pump outlet. Retain

white tapered gasket inside inlet (female) end of

check valve.

‘

25

PRESSURE

SWITCH

LIQUID CHECK

VALVE

WATER

PUMP

MOTOR

FIGURE 13. WATER PUMP AND MOTOR

 

 

1

 

 

3

 

2

 

 

6

 

 

 

4

 

 

5

Index

Part

 

No.

No.

Name

1

317963

Housing

2

312415

Flat Washer, Stainless Steel

3

*312418

Ba;; Seat (quad ring)

4

312419

Ball

5

312196

Spring

6

317965

Retainer

*Install new ball seat at each servicing.

FIGURE 14. LIQUID CHECK VALVE ASSEMBLY

3.Disassemble each check valve as shown in Figure 14

4.Wipe each part with clean lint–free cloth. Inspect each part, especially ball for burrs, nicks, corrosion, deterioration, and other damage. Discard ball seat and any damaged or suspicious parts and replace with new parts when reassembled.

5.Reassemble check valve as shown in Figure 14.

ALWAYS INSTALL NEW BALL SEAT (QUADDING) P/N 312418–000.

6.Make sure white tapered gasket is in place inside female end of check valve assembly, then install check valve assembly on fitting in water pump outlet port.

7.Connect pressure switch to check valve assembly outlet.

0713

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Manfactured IMI Cornelius INC ANOKA, Minnesota This Document Contains Important InformationTerms and Conditions General Warranty PolicyGeneral Description Ordering InformationIMI Cornelius Inc Complete ServiceDistribution Centers Specifications Installing Beverage Control Panel Assembly InstallationInstalling POST-MIX Dispensers Loose-Shipped Parts Name QtyFastening Beverage Control Panel Assembly to Wall Make Sure ALL Lines are Labeled for IdentificationPreparation for Operation No TAG0713 Sealing Ends of Floor Chase if Applicable Standard Beverage Control Panel ASS’Y Water Pressure Pressure Switch Check Water Valve Surge Tank Water Pump Pressure Switch Check Check Valve Water Pump PRE Filet BUN CO2/AIR and Syrup Systems Flow Diagram Sprite Diet Orange Coke Conn NBR Description QTY Sprite Diet Orange Coke Bulk Tank Conn NBR Description QTY Sprite Diet Orange Syrup Bulk Tank Conn NBR Description QTY Diet sprite coke Conn NBR Description QTY Beverage Control Panel Assembly Service Maintenance Service and MaintenancePOST-MIX Dispenser Service and Maintenance Hazard in the water systemAlways Install NEW Ball Seat Quadding P/N Pressure Switch Liquid Check Valve Water Pump MotorSwitch Cleaning Optional Syrup Lines Strainers see Figure BarsReplenishing Syrup Supply Sanitizing Syrup SystemsReplenishing CO2 Supply Cause serious personal injurySyrup Flavor Change Troubleshooting Gauge Reads TOO LOW CYCLES’’ CON’TWater Inlet Pressure Gauge Reads TOO HighDispensed Drinks have Not Operate CON’TAIR Compressor ‘SHORT ‘OFF’’ TasteWiring Diagram Carbonator Instructions for Crimping Tube Clamps Beverage Control Panel ASS’Y Beverage Control Panel ASS’Y CO2 Regulator ASS’Y P/N No. Part No Name CO2 Check Valve ASS’Y P/N NameCO2 Regulator ASS’Y Check Valve and Manifold ASS’Y P/N Large Reserve Carbonator Large Reserve Carbonator Water Manifold ASS’Y P/N Pump and Motor ASS’Y Regulator ASS’Y, HI-PRESSURE P/N Warranty

2232MS specifications

The Cornelius 2232MS is an advanced beverage dispensing system that combines cutting-edge technology with user-friendly features, making it an ideal choice for various commercial settings, such as restaurants, bars, and convenience stores. This model stands out due to its impressive performance and innovative design, which cater to the diverse needs of beverage service.

One of the key features of the Cornelius 2232MS is its high-capacity dispensing capability. The system can accommodate a wide range of beverage types, including carbonated soft drinks, teas, and flavored syrups. This versatility allows businesses to offer a broader menu, appealing to a wider customer base. The dispensers are designed to handle multiple flavors simultaneously, ensuring that patrons can enjoy their favorite drinks without long wait times.

Technology plays a critical role in the operation of the Cornelius 2232MS. The system is equipped with an advanced touchless dispensing interface, which minimizes the risk of cross-contamination and promotes a hygienic environment. Users can easily select their preferred beverage with just a touch, making the experience both efficient and enjoyable. Additionally, the unit features programmable settings that allow operators to customize drink proportions and carbonic acid levels, ensuring consistent quality in every pour.

Another notable characteristic of the Cornelius 2232MS is its energy-efficient design. The system utilizes eco-friendly technology that reduces power consumption, making it an environmentally responsible option for businesses. This energy efficiency not only contributes to cost savings on utility bills but also aligns with modern sustainability goals.

Maintenance and serviceability are also prioritized in the design of the Cornelius 2232MS. The unit features easy-to-access components for cleaning and servicing, which minimizes downtime. Regular maintenance can be performed with minimal effort, ensuring that the system remains in optimal condition for prolonged use.

In conclusion, the Cornelius 2232MS stands out in the beverage dispensing market due to its versatility, cutting-edge technology, and energy efficiency. Its user-friendly interface and easy maintenance make it a practical choice for any business looking to elevate their beverage service. With the Cornelius 2232MS, operators can expect enhanced customer satisfaction and improved operational efficiency, solidifying its position as a leader in beverage dispensing solutions.
Top Page Image Contents