Cornelius 2232MS Installation, Installing POST-MIX Dispensers, Loose-Shipped Parts Name Qty

Page 5

INSTALLATION

This manual is intended to assist the installer and service personnel in the installation, operation, and maintenance procedures to be performed on the Beverage Control Panel Assembly (see Figure 1 and applicable Figure 3, 4, 5, or 6).

The Beverage Control Panel Assembly is designed to filter, pressure regulator, and distribute plain and carbonated water, CO2 gas, and syrup to the Post–Mix Beverage Dispenser or dispensers and various other equipment connected to the system.

If your Beverage Control Panel Assembly is equipped with either or both the optional air compressor kit or the water pressure booster kit, dedicated properly grounded electrical outlets with proper electrical requirements must also be located close to the Beverage Control Panel Assembly installation location to provide electrical power.

No other electrical equipment should be connected to these electrical circuits. ALL ELECTRICAL WIRING MUST CONFORM TO NATIONAL AND LOCAL ELECTRICAL CODES.

NOTE: The Beverage Control Panel Assembly is manufactured in America and has American sizes on the hardware. All metric conversion are approximate and vary in size.

NOTE: The Beverage Control Panel Assembly was thoroughly inspected before leaving the factory and the carrier has accepted and signed for it. Any damage or irregularities should be noted at the time of delivery (or not later than 15 days from date of deliver) and immediately reported to the delivering carrier. Request a written inspection report from Claims Inspector to substantiate any necessary claim. File claim with the delivering carrier, not with IMI Cornelius Inc.

INSTALLING POST–MIX DISPENSER(S)

Refer to manual(s) provided with the Post–Mix Dispenser(s) for installation instructions, then install Dispenser(s) in operating location(s).

INSTALLING BEVERAGE CONTROL PANEL ASSEMBLY

Your Beverage Control Panel Assembly may be equipped with one or more of the optional kits as shown in Figure 2. Figure 1 shows the standard Beverage Control Panel Assembly with no optional kits and Figure 2 shows the panel assembly with optional kits installed.

NOTE: A dedicated and properly grounded electrical outlet with proper electrical requirements must be located close to the Beverage Control Panel Assembly installation location to provide electrical power to (depending upon Beverage Control Panel Model Number) one or two carbonators.

Table 2. Loose-Shipped Parts

Item

 

 

 

No.

Part No.

Name

Qty.

 

 

 

 

1

300894–000

Water Surge Tank

1

 

 

 

 

2

300893–000

Strap, Surge Tank

1

 

 

 

 

3

300912

Tube Ass’y, .375 I.D.

1

 

 

By 56–in long

 

 

 

 

 

4

311304

Tapered Gasket,

4

 

 

Black

 

 

 

 

 

5

0590

Elbow Ass’y, Surge

1

 

 

Tank

 

 

 

 

 

INSTALLING WATER SURGE TANK (ITEM 1) ON BEVERAGE CONTROL PANEL ASSEMBLY

NOTE: It is suggested for ease of assembly, that the loose–shipped WATER SURGE TANK (item 1) be installed on the Beverage Control Panel Assembly upper frame before the Panel Assembly is set upright and fastened to the wall.

1.Install ELBOW ASS’Y SURGE TANK (item 5) in top of WATER SURGE TANK (item 1) as shown in Figure 17. Seal pipe thread connection with pipe sealing compound.

2.Refer to applicable Figure 1 or 2 for water surge tank location on Beverage Control Panel Assembly upper frame, then remove two self–drilling screws from frame.

3.Position water surge tank in position on Beverage Control Panel Assembly.

4.Place STRAP, SURGE TANK (item 2) in position around water surge tank and align holes in strap with holes in frame where two self–drilling screws were removed.

5.Secure strap to frame with two self–drilling screws removed in step 2) preceding.

4

0713

 

Page 4 Page 6
Image 5
Page 4 Page 6
Contents This Document Contains Important Information Manfactured IMI Cornelius INC ANOKA, MinnesotaGeneral Description General Warranty PolicyTerms and Conditions Ordering InformationIMI Cornelius Inc Complete ServiceDistribution Centers Specifications Installing POST-MIX Dispensers InstallationInstalling Beverage Control Panel Assembly Loose-Shipped Parts Name QtyMake Sure ALL Lines are Labeled for Identification Fastening Beverage Control Panel Assembly to WallNo TAG Preparation for Operation0713 Sealing Ends of Floor Chase if Applicable Standard Beverage Control Panel ASS’Y Water Pressure Pressure Switch Check Water Valve Surge Tank Water Pump Pressure Switch Check Check Valve Water Pump PRE Filet BUN CO2/AIR and Syrup Systems Flow Diagram Sprite Diet Orange Coke Conn NBR Description QTY Sprite Diet Orange Coke Bulk Tank Conn NBR Description QTY Sprite Diet Orange Syrup Bulk Tank Conn NBR Description QTY Diet sprite coke Conn NBR Description QTY POST-MIX Dispenser Service and Maintenance Service and MaintenanceBeverage Control Panel Assembly Service Maintenance Hazard in the water systemPressure Switch Liquid Check Valve Water Pump Motor Always Install NEW Ball Seat Quadding P/NSwitch Bars Cleaning Optional Syrup Lines Strainers see FigureReplenishing CO2 Supply Sanitizing Syrup SystemsReplenishing Syrup Supply Cause serious personal injurySyrup Flavor Change Troubleshooting Water Inlet Pressure CYCLES’’ CON’TGauge Reads TOO LOW Gauge Reads TOO HighAIR Compressor ‘SHORT Not Operate CON’TDispensed Drinks have ‘OFF’’ TasteWiring Diagram Carbonator Instructions for Crimping Tube Clamps Beverage Control Panel ASS’Y Beverage Control Panel ASS’Y CO2 Regulator ASS’Y P/N CO2 Check Valve ASS’Y P/N Name No. Part No NameCO2 Regulator ASS’Y Check Valve and Manifold ASS’Y P/N Large Reserve Carbonator Large Reserve Carbonator Water Manifold ASS’Y P/N Pump and Motor ASS’Y Regulator ASS’Y, HI-PRESSURE P/N Warranty

2232MS specifications

The Cornelius 2232MS is an advanced beverage dispensing system that combines cutting-edge technology with user-friendly features, making it an ideal choice for various commercial settings, such as restaurants, bars, and convenience stores. This model stands out due to its impressive performance and innovative design, which cater to the diverse needs of beverage service.

One of the key features of the Cornelius 2232MS is its high-capacity dispensing capability. The system can accommodate a wide range of beverage types, including carbonated soft drinks, teas, and flavored syrups. This versatility allows businesses to offer a broader menu, appealing to a wider customer base. The dispensers are designed to handle multiple flavors simultaneously, ensuring that patrons can enjoy their favorite drinks without long wait times.

Technology plays a critical role in the operation of the Cornelius 2232MS. The system is equipped with an advanced touchless dispensing interface, which minimizes the risk of cross-contamination and promotes a hygienic environment. Users can easily select their preferred beverage with just a touch, making the experience both efficient and enjoyable. Additionally, the unit features programmable settings that allow operators to customize drink proportions and carbonic acid levels, ensuring consistent quality in every pour.

Another notable characteristic of the Cornelius 2232MS is its energy-efficient design. The system utilizes eco-friendly technology that reduces power consumption, making it an environmentally responsible option for businesses. This energy efficiency not only contributes to cost savings on utility bills but also aligns with modern sustainability goals.

Maintenance and serviceability are also prioritized in the design of the Cornelius 2232MS. The unit features easy-to-access components for cleaning and servicing, which minimizes downtime. Regular maintenance can be performed with minimal effort, ensuring that the system remains in optimal condition for prolonged use.

In conclusion, the Cornelius 2232MS stands out in the beverage dispensing market due to its versatility, cutting-edge technology, and energy efficiency. Its user-friendly interface and easy maintenance make it a practical choice for any business looking to elevate their beverage service. With the Cornelius 2232MS, operators can expect enhanced customer satisfaction and improved operational efficiency, solidifying its position as a leader in beverage dispensing solutions.
Top Page Image Contents