Estate W10121806C Pilot and Bypass Screws Conversion, Complete Conversion, Natural Gas Conversion

Page 12

3.Locate LP gas orifice spud stamped “56” in the bag containing literature supplied with the range.

4.Use a ³⁄₈" combination wrench and remove the Natural gas orifice spud.

5.Install the number “56” LP gas spud.

A

A. LP oven orifice spud stamped with “56”

IMPORTANT: Do not over tighten.

6.Place Natural gas oven burner spud in plastic parts bag along with Natural gas cooktop burner spuds for future use and keep with the bag containing literature.

7.Reinstall oven burner.

8.Reinstall oven racks, oven tray and flame spreader.

Pilot and Bypass Screws Conversion

1.Remove control knobs and set aside.

2.Remove upper grates.

3.Lift the cootop by both front corners unti the side support rods snap into position.

4.Open oven door.

5.Locate the two top fasteners and two bottom fasteners and remove them using a Phillips head screwdriver.

A

B

A. Top fasteners

B. Bottom fasteners

6.Set the front panel aside and locate the oven thermostat.

A

A. Oven thermostat

7.Locate the LP gas bypass screw in the bag containing literature included with the range. One LP gas bypass screw is stamped “48.”

8.Remove the Natural gas bypass screw with a flat-blade screwdriver, turning counterclockwise.

9.Install the LP gas bypass screw with a flat-blade screwdriver, turning clockwise.

A

B

A. Pilot screw

B. Bypass screw

10.Locate the LP gas pilot screw in the bag containing literature included with the range. One LP gas pilot screw is stamped “15.”

11.Remove Natural gas pilot screw with a flat-blade screwdriver, turning counterclockwise.

12.Install the LP gas pilot screw with a flat-blade screwdriver, turning clockwise.

13.Replace the front panel and screw bottom and top fasteners in place.

14.Replace the control knobs. Push back on the side support rods and slowly lower the cooktop until it snaps into position. Close the oven door.

Complete Conversion

1.Refer to the “Make Gas Connection” section for properly connecting the range to the gas supply.

2.Turn the manual shutoff valve in the gas supply line to the open position.

3.Refer to the “Check Operation” section for proper burner ingnition, operation and burner flame adjustments.

IMPORTANT: You may have to adjust the “LO” setting for each cooktop burner.

Checking for proper cooktop and oven burner flames is very important. The small inner cone should have a very distinct blue flame ¼" to ½" (0.64 cm to 1.3 cm) long. The outer cone is not as distinct as the inner cone. LP gas flames have a slightly yellow tip.

4.Close the broiler door and turn the knob to “OFF.”

5.Refer to the “Complete Installation” section to complete this procedure.

Natural Gas Conversion

To Convert Gas Pressure Regulator

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket, if the range is moved.

Failure to follow these instructions can result in death or serious burns to children and adults.

12

Image 12
Contents Table of Contents/Índice Range Safety Your safety and the safety of others are very importantInstallation Requirements Tools and PartsLocation Requirements Product Dimensions Freestanding Range Cabinet DimensionsMobile home installations require Gas Supply Requirements Installation Instructions Install Anti-Tip BracketLine pressure testing above ½ psi gauge 14 WCP Line pressure testing at ½ psi gauge 14 WCP or lowerMake Gas Connection Typical rigid pipe connectionLevel Range Verify Anti-Tip Bracket LocationCheck Operation If the low flame needs adjusting Check Operation of Oven/Broil BurnerComplete Installation If the flame needs adjustingIf you need Assistance or Service GAS ConversionsTo Convert Gas Pressure Regulator To Convert Surface BurnersTo Convert Oven Burner Pilot and Bypass Screws Conversion Complete ConversionNatural Gas Conversion To Convert Surface Burners Pilot and Bypass Screws Conversion Seguridad DE LA Estufa Requisitos DE Instalación Piezas y herramientasRequisitos de ubicación Medidas del producto Estufa autónoma Espacios libres para instalaciónLas instalaciones en casas rodantes necesitan Requisitos del suministro de gas Tipo de gasLínea de suministro de gas Regulador de la presión de gasInstrucciones DE Instalación Desempaque la estufaInstalación del soporte anti-vuelco Prueba de presión del suministro de gasConexión del suministro de gas Verificación de la ubicación del soporte Anti-vuelco Nivelación de la estufaVerifique el funcionamiento Verifique el funcionamiento del quemador de asar/del horno Si la llama baja necesita ajustarseComplete la instalación Si la llama necesita ajustarseSi necesita ayuda o servicio técnico Si la estufa no funciona, revise lo siguienteConversiones DE GAS Conversión de gas LPCómo convertir el regulador de la presión del gas Conversión de tornillos de desvío y piloto Cómo convertir los quemadores de superficieCómo convertir el quemador del horno Complete la conversión Conversión de gas naturalEspitas de los orificios Válvulas Obturador de aire W10121806C