Aiwa NSX-DS8 Timer Recording, 5Adjust the volume, 6Prepare the source, To check the timer setting

Page 29
5Adjust the volume.

5Adjust the volume.

The source sound will play at the volume level set in this step when the power is turned on by the timer.

If the volume level is set to 21 or higher, however, it will automatically be set to 20 when the power is turned on.

6Prepare the source.

To listen to a CD, load the disc to be played first on tray 1. To listen to a tape, insert the tape into deck 1 or 2.

To listen to the radio, select the band and tune in to a station.

7Press POWER to turn off the power.

When the timer-on time is reached, the unit turns on and begins play with the selected source.

NOTE

You can change the source that was selected in step 1 by pressing one of the function buttons before pressing ENTER or a in step 3.

To check the timer setting

Press TIMER.

The timer-on time, the selected source, and the duration for the timer-activated period will be displayed for 4 seconds.

To change any of the previous setting

Carry out from step 1.

However, if you do not change the timer-on time, in step 3 just press ENTER twice and continue from step 4.

To cancel the timer standby mode temporarily

Press TIMER repeatedly so that “ ” disappears.

To restore the timer standby mode, press again to display “ ”.

Using the unit while the timer is set

You can use the unit normally after setting the timer. Before turning off the power, carry out steps 5 and 6.

To play back an external source by the timer

Select the appropriate source in step 1 (see “Listening to external sources ”, page 32). Connected equipment cannot be turned on and off by the built-in timer of this unit. Use an external timer.

NOTE

Timer playback and timer recording will not begin unless the power is turned off.

TIMER RECORDING

Timer recordng applies only for the TUNER or analog external

TIMER

sources.

 

Use an external timer for an external source.

 

Digital input from external equipment cannot be recorded.

 

Press either TUNER/BAND or VIDEO1/DVD/AUX to select a

 

source, then press TIMER repeatedly until “

REC” appears

 

on the display. Within 6 seconds, carry out the steps of “SETTING THE TIMER” from step 3 and insert the tape to be recorded on into deck 2 after step 6.

NOTE

•If the timer recording is done with the economizing mode (page

7)set to “ECO ON” or “ECO AUTO” and the power turns off, the dimmer mode will be set to dimmest and the volume level will be 0 (minimum level) the next time the power is turned on.

•You cannot use the timer function to record from a CD or tape.

•You can check the timer setting by pressing TIMER even while the power is off. In this case, if you press ENTER or awithin 4 seconds after pressing TIMER, you can enter the timer setting mode and change the previous setting.

En

ENGLISH 29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents NSX-DS8 For assistance and informationCOMPACT DISC STEREO SYSTEM Owner’s recordENGLISH PRECAUTIONSInstallation Electric PowerTIMER TABLE OF CONTENTSOTHER FEATURES NSX-DS8Before connecting the AC cord CONNECTIONSPREPARATIONS 1 Connect the right speaker to the main unitPREPARATIONS POSITIONING THE SPEAKERS5 Connect the supplied antennas 7 Connect the television to the video equipmentCONNECTING AN OUTDOOR ANTENNA REMOTE CONTROLWhen to replace the batteries Using the remote controlBEFORE OPERATION SETTING POWER ECONOMIZING MODEDEMO DEMONSTRATION DIMMER MODEAUDIO ADJUSTMENTS SETTING THE CLOCKVOLUME BBE SYSTEMSUPER T-BASSSYSTEM GRAPHIC EQUALIZERSELECTING THE PROGRAMMED EQUALIZATION CURVESTORING THE NEW EQUALIZATION CURVES SETTING A NEW EQUALIZATION CURVE MANUALLY1Press GEQ, followed by ENTER within 4 seconds 3Press ENTER to let “GEQ HIGH” showSELECTING A PROGRAMMED DSP SURROUND MODE DSP SURROUNDMULTI-AMPLIFIERSYSTEM BUILT-INSUBWOOFER SYSTEMPRESETTING STATIONS MANUAL TUNINGPRESET NUMBER TUNING preset numberTAPE PLAYBACK BASIC OPERATIONS2Press d to start play To select a reverse mode deck 2 onlyMUSIC SENSOR CONTINUOUS PLAY1Insert tapes into deck 1 and deck 3Press REV MODE to selectPLAYING DISCS LOADING DISCSSelecting a track with the remote control BASIC OPERATIONSRANDOM/REPEAT PLAY PROGRAMMED PLAYBLANK SKIP PLAY 1Press CD BLANK SKIPINSERTING BLANK SPACES BASIC RECORDINGTo start recording with the remote control Sound adjustment during recordingDUBBING THE WHOLE TAPE DUBBING A TAPE MANUALLY1Press TAPE/DECK 1/2 to be recorded on into deck6 Press w REC/REC MUTE to start recording on AI EDIT RECORDINGRECORDING the first side4Press numbered buttons on the remote control PROGRAMMED EDIT RECORDINGthe remote control to program a track 1Insert the tape into deckSOUND PLAYING DOLBY SURROUNDPlaying Dolby Digital Sound Playing Dolby Pro Logic SoundPhantom and 3 Stereo modes ADDITIONAL DOLBY SURROUND MODESOverview of the available modes The Subwoofer On or Off modeADJUSTING SOUND LEVEL OF SPEAKERS OTHER ADJUSTMENTSADJUSTING LOW-FREQUENCYEFFECT LEVEL SPEAKER LEVEL BALANCE ANDADJUSTING DYNAMIC RANGE ADJUSTING DELAY TIMEcontrol to select the delay time to adjust 3Press rf or gt to adjust the delay timeVOCAL FADER/MULTIPLEX FUNCTIONS MICROPHONE MIXING3Adjust the volume and tone of the source 4Press MIC and turn VOLUME within 4 seconds to1Play the Dolby Digital karaoke disc USING DOLBY DIGITAL KARAOKE DISCS2Press DOLBY SURROUND repeatedly to select the 2CH STEREO mode1Press CD and load the discs 2Press PRGM once KARAOKE PROGRAM4Repeat step 3 to reserve other tracks 5Press d to start playSETTING THE TIMER SETTING THE SLEEP TIMERTIMER to specify the time until the power is turned off5Adjust the volume TIMER RECORDING7Press POWER to turn off the power TIMEROTHER FEATURES DEMO DemonstrationTo cancel the game Demo To reset the game DemoVIDEO1/DVD/AUX OR VIDEO2/LD/MD JACKS CONNECTING OPTIONAL EQUIPMENTLINE OUT JACKS SUB WOOFER JACKPLAYING AN EXTERNAL ANALOG SOURCE LISTENING TO EXTERNAL SOURCESPLAYING AN EXTERNAL DIGITAL SOURCE To adjust the sound level of the external sourceTROUBLESHOOTING GUIDE CARE AND MAINTENANCETo clean the cabinet To clean the tape headsMain unit CX-NDS8 FM tuner section SPECIFICATIONSAM tuner section Amplifier sectionINDICE DE LAS PARTES NOMENCLATURE PARTS INDEXName/Nombre/Nom For assistance and informationPRECAUCIONES ESPAÑOLADVERTENCIA Instalació nNSX-DS8 INDICEPREPARATIVOS SONIDOPREPARATIVOS CONEXIONES1Conecte el altavoz derecho a la unidad principal 3Conecte los altavoces de sonido ambientalPREPARATIVOS UBICACION DE LOS ALTAVOCES5Conecte las antenas suministradas 7Conecte el televisor al equipo de vídeoCONEXION DE UNA ANTENA EXTERIOR CONTROL REMOTOc/d PRESET en el control remoto Para posicionar las antenas Antena de FMDEMO Demostració n ANTES DE LA OPERACIONACTIVACION DEL MODO DE AHORRO DE ENERGIA MODO DE INTENSIDAD DE ILUMINACIONAJUSTES DE AUDIO CONTROL DE VOLUMENPUESTA EN HORA DEL RELOJ SISTEMA BBESISTEMA SUPER T-BASS ECUALIZADOR GRAFICOSELECCION DE LA CURVA DE ECUALIZACION PROGRAMADAALMACENAMIENTO DE CURVAS DE ECUALIZACION NUEVAS AJUSTE MANUAL DE UNA CURVA DE ECUALIZACION NUEVA3Pulse ENTER para que se muestre “GEQ HIGH” 1Siga los pasos 1-4de “Ajuste manual de unaSistema multiamplificador SELECCION DE UN MODO DSP SURROUND PROGRAMADOSistema de altavoz de subgraves incorporado Para cancelar el modo seleccionadoPREAJUSTE DE EMISORAS SINTONIZACION MANUALSINTONIZACION MEDIANTE NUMERO DE PREAJUSTE RECEPCION DE LA RADIOREPRODUCCION DE CINTAS OPERACIONES BASICAS2Pulse d para iniciar la reproducció n RADIOLADESENSOR MUSICAL REPRODUCCION CONTINUA1Inserte cintas en las platinas 1 y 3Pulse REV MODE para seleccionarREPRODUCCION DE DISCOS INTRODUCCION DE DISCOSOPERACIONES BASICAS REPRODUCCION DE DISCOS COMPACTOSREPRODUCCION CON SALTO DE SECCIONES EN BLANCO REPRODUCCION PROGRAMADA1Pulse CD BLANK SKIP 2Pulse d para iniciar la reproducció nINSERCION DE ESPACIOS SIN GRABAR GRABACION BASICAGRABACION 1Inserte la cinta que vaya a grabar en la platinaCOPIADO DE TODA LA CINTA COPIADO MANUAL DE UNA CINTA1Pulse TAPE/DECK 1/2 que vaya a grabar en la platina6Pulse wREC/REC MUTE para iniciar la grabació n GRABACION CON EDICION AIde la primera cara GRABACION1Inserte la cinta en la platina GRABACION CON EDICION PROGRAMADA2Pulse CD e introduzca ellos discos 3Pulse dos vecesCD EDIT/CHECKREPRODUCCION DEL SONIDO DOLBY SURROUNDReproducció n de sonido Dolby Digital Reproducció n de sonido Dolby Pro LogicModos Phantom y 3 Stereo MODOS DOLBY SURROUND ADICIONALESPerspectiva general de los modos disponibles El modo Subwoofer On u OFFALTAVOCES Y OTROS AJUSTES EQUILIBRIO DEL NIVEL DE LOSAJUSTE DEL NIVEL DEL SONIDO DE LOS ALTAVOCES AJUSTE DEL NIVEL DEL EFECTO DE BAJA FRECUENCIAAJUSTE DE LA GAMA DINAMICA AJUSTE DEL TIEMPO DE RETARDO1Reproduzca el sonido Dolby Surround 3Pulse rfo gtpara ajustar el tiempo de retardoFUNCIONES DE DESVANECIMIENTO DE VOZ/MULTIPLEX MEZCLA MICROFONICA5Pulse ECHO y gire VOLUME antes de que pasen KARAOKE1Reproduzca el disco de karaoke Dolby Digital UTILIZACION DE DISCOS DE KARAOKE DOLBY DIGITAL2Pulse repetidamente DOLBY SURROUND para seleccionar el modo 2CH STEREO1Pulse CD e introduzca los discos PROGRAMA DE KARAOKE2Pulse PRGM una vez 4Repita el paso 3 para reservar otras cancionesAJUSTE DEL TEMPORIZADOR PARA DORMIR AJUSTE DEL TEMPORIZADORTEMPORIZADOR 1Pulse SLEEP5Ajuste el volumen GRABACION CON TEMPORIZADOR7Pulse POWER para desconectar la alimentació n 6Prepare la fuentePara cancelar el juego DEMO DemostraciónOTRAS CARACTERISTICAS Para disfrutar del juegoTOMAS VIDEO1/DVD/AUX O VIDEO2/LD/MD CONEXION DE UN EQUIPO OPCIONALTOMAS LINE OUT TOMA SUBWOOFERREPRODUCCION DE UNA FUENTE ANALOGICA EXTERIOR ESCUCHA DE FUENTES EXTERIORESREPRODUCCION DE UNA FUENTE DIGITAL EXTERIOR 1Seleccione la entradaGUIA PARA LA SOLUCION DE PROBLEMAS CUIDADOS Y MANTENIMIENTOGENERALIDADES GENERALIDADES OTRAS CONEXIONESUnidad principal CX-NDS8 ESPECIFICACIONESSecció n del sintonizador de FM Secció n del sintonizador de AMAVERTISSEMENT FRANÇAISPRECAUTIONS InstallationNSX-DS8 TABLE DES MATIERESPREPARATIONS RECEPTION RADIOPREPARATIONS CONNEXIONS3Connecter les enceintes surround 4Connecter l’enceinte centralePREPARATIONS POSITIONNEMENT DES ENCEINTES5Connecter les antennes fournies 7Connecter le té lé viseur à l’appareil vidé oCONNEXION D’UNE ANTENNE EXTERIEURE TELECOMMANDEUtilisation de la té lé commande c/d PRESET de la té lé commandeAVANT L’UTILISATION MISE EN SERVICE DU MODE ECONOMIE D’ENERGIEMODE VARIATEUR DEMO Dé monstrationREGLAGES AUDIO REGLAGE DE L’HORLOGESYSTEME BBE VOLUMESYSTEME SUPER T-BASS EGALISEUR GRAPHIQUESELECTION D’UNE COURBE D’EGALISATION PROGRAMMEE1Appuyer sur GEQ, puis appuyer sur ENTER dans MEMORISATION DES NOUVELLES COURBES D’EGALISATIONles quatre secondes 3Appuyer sur ENTER pour faire apparaître “GEQSystè me multi-amplificateur SELECTION D’UN MODE DSP SURROUND PROGRAMMESystè me à haut-parleurinfragrave inté gré Pour ré gler le volume des enceintes surroundMEMORISATION DE STATIONS ACCORD MANUELACCORD PAR NUMERO DE PREREGLAGE RECEPTION RADIOLECTURE DE CASSETTES OPERATIONS DE BASE2Appuyer sur d pour dé marrer la lecture CASSETTESDESENSEUR DE MUSIQUE LECTURE CONTINUE1Insé rer des cassettes dans les platines 1 et 3Appuyer sur REV MODE pour sé lectionnerLECTURE DE DISQUES MISE EN PLACE DE DISQUESSé lection d’une plage avec la té lé commande OPERATIONS DE BASELECTURE ALEATOIRE/REPETEE LECTURE PROGRAMMEELECTURE AVEC SAUT DES BLANCS 1Appuyer sur CD BLANK SKIPINSERTION D’ESPACES BLANCS ENREGISTREMENT DE BASEENREGISTREMENT 2Appuyer sur REV MODE pour sé lectionner le1Appuyer sur TAPE/DECK 1/2 DUPLICATION MANUELLE D’UNE CASSETTEla cassette à enregistrer dans la platine 3Appuyer sur TAPE/DECK 1/2 pour sé lectionnerl’enregistrement sur la premiè re face 6 Appuyer sur w REC/REC MUTE pour dé marrer1Insé rer la cassette dans la platine 2Appuyer sur CD et mettre les disques en place1Insé rer la cassette dans la platine ENREGISTREMENT AVEC MONTAGE PROGRAMME2Appuyer sur CD et mettre les disques en place 3Appuyer deux foissur CD EDIT/CHECKSURROUND LECTURE AVEC SON DOLBYEcoute de son Dolby Digital Ecoute de son Dolby Pro LogicAUTRES MODES DOLBY SURROUND Mode caisson de graves en ou hors serviceModes Phantom et 3 Stereo Vue d’ensemble des modes disponiblesREGLAGE DU NIVEAU D’EFFET AUX BASSES FREQUENCES BALANCE DES NIVEAUX DESREGLAGE DU NIVEAU SONORE DES ENCEINTES té lé commande pour ré gler le niveau sonore desREGLAGE DE LA GAMME DYNAMIQUE REGLAGE DU TEMPS DE RETARD1Faire une lecture avec son Dolby Surround 1Faire une lecture avec son Dolby DigitalFONCTIONS VOCAL FADER/MULTIPLEX MIXAGE AVEC MICROPHONE3Ré gler le volume et la tonalité de la source 5Appuyer sur ECHO puis tourner VOLUME dansMultiplex UTILISATION DE DISQUES KARAOKE EN DOLBY DIGITALFonction de guide mé lodique 26 FRANÇ AIS1Appuyer sur CD et mettre les disques en place PROGRAMME DE KARAOKE2Appuyer une foissur PRGM 5Appuyer sur d pour dé marrer la lectureREGLAGE DE LA MINUTERIE REGLAGE DE LA MINUTERIE D’ARRET2Appuyer sur TIMER à plusieurs reprises jusqu’à MINUTERIE5Ré gler le volume ENREGISTREMENT COMMANDE PAR MINUTERIE7Appuyer sur POWER pour mettre l’appareil hors 6Pré parer la sourceAUTRES CARACTERISTIQUES DEMO DémonstrationUtilisation du jeu Demo 2Appuyer sur dPRISES VIDEO1/DVD/AUX OU VIDEO2/LD/ MD CONNEXION D’UN APPAREIL OPTIONNELPRISES LINE OUT PRISE SUB WOOFERUTILISATION D’UNE SOURCE ANALOGIQUE EXTERNE ECOUTE DE SOURCES EXTERNESUTILISATION D’UNE SOURCE NUMERIQUE EXTERNE 1Sé lectionner l’entré eSOINS ET ENTRETIEN EN CAS DE PROBLEMEGENERALITES CONNEXIONSAppareil principal CX-NDS8 Partie tuner FM SPECIFICATIONSPartie tuner AM Partie amplificateur
Top Page Image Contents