Franklin Industries, L.L.C FIM120, FIM90 user manual Technical Information

Page 6

it is your responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet. The ice maker should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating label on the appliance. This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires. Never unplug your ice maker by pulling on the power cord. Always grip the plug firmly and pull straight out from the outlet. Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end. When moving the ice maker, be careful not to damage the power cord.

Extension Cord

Because of potential safety hazards under certain conditions, it is strongly recommended that you do not use an extension cord with this ice maker.

Technical Information

	Model	FIM70	FIM90	FIM120
	Rated power	115VAC ~ 60Hz ~	115VAC ~ 60Hz ~	115VAC ~ 60Hz ~
	Rated power	470W	520W	580W
		470W	520W	580W
	Ice-making rated current	6.7A	7.3A	7.5A
	Ice-harvest rated current	11.2A	11.7A	11.8A
	Refrigerant	R134a, 6.88 oz.	R134a, 8.96 oz.	R134a, 9.92 oz.
	High side pressure	320 psi	320 psi	320 psi
	Low side pressure	120 psi	120 psi	120 psi
	Width x depth x height	16.5”x21.3”x32.5”	22.1”x21.3”x32.5”	22.1”x21.3”x32.5”
	Unit weight	91 lbs	106 lbs	102 lbs
	Ice-making capacity	Up to 65 lbs/day*	Up to 83 lbs/day*	Up to 110 lbs/day*

The technical data and performance index listed above should be used for reference only. They are subject to change.

*The actual quantity of ice produced per day can vary with room and water conditions.

5

Image 6

Contents Models/Modelos/Modèles FIM70, FIM90, FIM120 Table of Contents ICE Maker Safety Your safety and the safety of others are very importantImportant Safeguards Electrical Connection Technical Information Introduction Component Locations Unpacking ICE Maker InstallationCleaning before use Location RequirementsPage Electrical Requirements Electrical Shock HazardRecommended grounding method Leveling the Ice Maker Water Supply and Drain ConnectionsTools required Connecting the water line Connecting the drain lineEnclosed Installation Installation TypesMobile Installation Built-in InstallationOperation Final Check List before OperationOperating Method How the Machine Makes IcePage Preparing the Ice Maker for Long Storage What should be kept clean Cleaning and MaintenanceExterior Cleaning What shouldn’t be doneCondenser Cleaning Interior Cleaning Page Page Page Descriptions of LEDs and buttons Major Functions Before Calling for Service Problem Possible Cause Probable CorrectionProblem Possible Cause Probable Correction Limited Warranty Franklin Industries, L.L.C First Avenue Brooklyn, NY TelPage Índice PáginaSímbolos Y Advertencias DE Seguridad Advertencias DE Seguridad Page Conservar Estas Instrucciones Conexión eléctricaCordón prolongador Información técnica Introducción Ubicación DE Componentes DE LA Máquina Instalación de la Máquina DesembalajeRequisitos del lugar de instalación Page Requisitos de alimentación eléctrica Peligro de electrocuciónNivelación de la máquina Conexiones de entrada de agua y drenajeCircuito de descarga a tierra Herramientas necesarias Conexión de la línea de aguaTipos de instalación Conexión del drenajeInstalación libre Instalación en cerramiento Instalación empotradaUSO DE LA Máquina Lista de control final antes de la puesta en servicioMétodo de uso Ciclos de funcionamiento de la máquinaSonidos normales El circuito de agua en la máquinaPreparación de la máquina para almacenamiento prolongado Lo que no se debe hacer Limpieza Y MantenimientoLimpieza externa Lo que se debe mantener limpioLimpieza del condensador Limpieza interna Page Limpieza del sistema para hacer hielo Page Tablero de control detrás de la tapa frontal Descripción de luces LED y botonesFunciones Principales Problema Posible causa Solución probable Diagnóstico DE FallasAntes de llamar al servicio de reparación Revisar el filtro de agua podría estar bloqueado Garantía limitada Franklin Industries, L.L.C First Avenue Brooklyn, NY TelPage Page Installation DE L’APPAREIL Table des matièresSécurité de l’appareil Sauvegarder ces instructionsPrécautions Importantes Sauvegarder CES Instructions Branchement électriqueInformations Techniques Câble de rallongeIntroduction Positions DES Composants Déballage Installation de l’appareilSpécifications pour l’emplacement Enlever les matériaux d’emballagePage Spécifications électriques Risque d’électrocutionMéthode de mise à la terre recommandée Mise à niveau de l’appareil pour la fabrication des glaçonsBranchement de l’alimentation d’eau et du drainage Outils nécessaires Branchement de l’alimentation d’eauTypes d’installation Installation MobileBranchement de la ligne de drainage Installation Enfermée Installation IncorporéeCheck-list finale avant la mise en service FonctionnementMode opératoire Procédé de fabrication de la glaceBruits qui indiquent un fonctionnement normal Utilisation de l’eau dans la machinePage Ce qu’il ne faudrait pas faire Entretien et NettoyageNettoyage extérieur Ce qui doit être gardé propreNettoyage du condenseur Nettoyage intérieur Page Nettoyage du système de fabrication de la glace Page Instructions pour les diodes LED et les boutons Tableau de contrôle derrière la couverture de devantFonctions principales Guide à la solution des problèmes Solution des problèmesAvant d’appeler le service d’entretien Problème Cause possible Remède probableLe corps de l’app Garantie limitée Franklin Industries, L.L.C First Avenue Brooklyn, NY TélFIM70-OM-ESF-2