Best WM24E manual Halogen Bulbs, Fuse Replacement, Eration on the appliance

Page 6

HEAT SENTRY™

Your hood is equipped with a HEAT SENTRY™ thermostat. This thermostat is a device that will turn on or speed up the blower if it senses excessive heat above the cooking surface.

1)If blower is OFF - it turns blower ON to HIGH speed.

2)If blower is ON at a lower speed setting - it turns blower up to HIGH speed. When the temperature level drops to normal, the blower will return to its original setting.

WARNING

The HEAT SENTRY thermostat can start the blower even if the hood is turned OFF. When this occurs, it is impossible to turn the blower OFF with its switch. If you must stop the blower, do it from the main electrical panel.

HALOGEN BULBS

This range hood requires four halogen bulbs (Type T3, 12Volt, 20Watt Max, G-4 Base).

WARNING: Always switch off the elec- trical supply before carrying out any op-

eration on the appliance.

To change bulbs:

1.Open the cover by prying from the proper slots.

2.Remove the bulb by pulling sideways. (DO

NOT ROTATE).

! CAUTION: Bulb may be hot.

3.Replace with Type T3, 12Volt, 20 Watt Max, G-4 Base halogen bulb. Do not touch replacement bulb with bare hands!

! CAUTION: Use of bulbs greater than 20 watts will cause the fuse to open.

FUSE REPLACEMENT

FUSE

IF LIGHTS FAIL TO OPERATE, DISCON-

NECT POWER AT THE SERVICE EN-

TRANCE. CHECK THE FUSE AND RE-

PLACE IF NECESSARY.

1.Remove the grease filters.

2.Unscrew the cap from the fuse holder and remove the fuse.

3.Replace the fuse with the same size and amperage (5 x 20mm, 4 amp, 125 volt).

! CAUTION: Use a fuse greater than 4 amps may damage the transformer.

4.Reinstall the fuse holder cap.

5.Reconnect power at the service entrance.

-6 -

Image 6

Contents Model WM24E Read and Save These Instructions Intended for Domestic Cooking only ! WarningPage Maintenance Hood CleaningGrease Filters Operation ControlsFuse Replacement Halogen BulbsEration on the appliance Prepare the Hood Install the Ductwork Exterior or IN-LINE Blower SelectionIN-LINE Blower Wiring Exterior or In-line blower connectionPower connection at hood Remove the wiring box coverRemove the 4 screws Fig Mounting screws 3.9x9.5mm Black Install the Hood Warranty Broan ONE Year Limited WarrantyLisez ET Conservez CES Instructions Seulement Pour Utilisation Domestique AvertissementsPage Entretien Filtres anti-graisseNettoyage de votre hotte Commandes FonctionnementRemplacement Fusible Ampoules Halogenes’appareil Preparez LA Hotte Ventilateur Externe Ventilateur IN-LINE Installation Electrique Branchement du ventilateur externe ou «in-Line»Branchement du courant à la hotte LINE-INPréparation DE LA Hotte Diamètre DU Conduit Collier ’EVACUATION Installation DE LA Hotte PlafondGarantie Garantie Broan Limitée À UN ANLEA Y Conserve Estas Instrucciones AdvertenciaAdvertencia Mantenimiento Filtros antigrasaLimpieza de la campana Funcionamiento MandosLamparas Halogenas Sustitucion FusibleAtención las lámparas pueden estar calientes Prepare LA Campana Decorativo Tornillos DESelección DEL Ventilador Exterior O DEL Ventilador IN-LINE Instalacion DEL Tubo DE ExtraccionVentilador IN-LINE Instalación Eléctrica Blanco, el rojo con el negro y el verdeConexión del ventilador exterior o In- Line Conexión de la corriente a la campana CON.DE Energia a LA CampanaPreparación DE LA Campana Conducto DE 8 DE Diámetro Casquillo Tornillos DE Montaje Instalación DE LA Campana TechosGarantia Garantia Broan POR UN AÑOService Parts Model WM24EListe Pieces DE Rechange Modele WM24ELista DE Piezas DE Recambio Modelo WM24EModel WM24E 04307489/4N