Vermont Casting DVBR36, DVBR42 manual Optional Top Vent Application

Page 9

Optional Top Vent Application

The DVBR36/42 fireplace is shipped as a rear vent unit. If the layout requires a top vent, convert the unit follow- ing the steps below.

DVBR36

1.Remove the eight (8) screws securing outer collar adapter to fireplace. (Be careful not to damage insu- lation.) (Fig. 10)

2.Set outer collar adapter aside.

Remove

Rear View

Screws (4)

 

Outer Collar

Adapter

Flue Pipe

Remove Screws (4)

DVT584-602

Fig. 10 Remove screws from outer collar adapter.

3.Remove insulation on top of collector box. (Fig. 11)

4.Remove the four (4) screws securing flue cover to top of unit and remove flue cover. (Fig. 11)

5.Remove the four (4) screws securing flue pipe to back of unit. Remove flue pipe. (Fig. 11)

 

 

Insulation

 

 

Remove

Flue

 

Screws (4)

 

 

Cover

 

 

Flue

 

 

Pipe

 

 

 

Remove Screws

DVT584-603

 

(4)

 

 

Fig. 11 Remove flue cover and flue pipe.

DVBR Series Direct Vent Gas Fireplace

6.Secure flue cover to back of flue outlet. Be sure to replace gasket. (Fig. 12)

7.Install flue pipe to top of unit with four (4) screws. Be sure to replace gasket. (Fig. 12)

8.Set insulation in back of unit foil side down.

9.Secure outer collar adapter to unit with the round collar on top, secure with eight (8) screws.

NOTE: Be sure not to damage any gasket material.

Flue Pipe

Flue

Pipe Replace

Screws (4)

Replace Screws

(4)

Foil Side

Insulation

DVT584-604

Fig. 12 Replace flue cover and flue pipe.

 

DVT584-605

Fig. 13

Completed conversion.

20000584

9

Image 9
Contents DVBR42 Table of Contents Please Read the Following Carefully Installation InstructionsFraming Dimensions Fireplace Dimensions Installed as Top VentFireplace Dimensions Installed as Rear Vent Clearance to Combustibles Locating Your FireplaceMantels ApplianceHearth Gas Line InstallationFraming and Finishing Final FinishingEB-1 Electrical Box Remote Switch InstallationDVBR36 Optional Top Vent ApplicationLocation of Vent Termination General VentingGeneral Venting Information Termination Location Canadian Installations1 US Installations2USA Installations Canadian InstallationsGeneral Information Assembling Vent Pipes Flex Vent PipesHow to Use the Vent Graph Twist Lock PipesRear Wall Vent Applications Zero clearance sleeve is only required for combustible walls Rear Wall Vent Installations Twist Lock PipeVertical Sidewall Applications Rear Wall Vent Installations Flex Vent PipeHorizontal run reduction Total angular variation 270Always install horizontal venting on a level plane Vertical Sidewall Installation Twist Lock PipeStep Vertical Sidewall Installation Flex Vent PipeVertical Through-the-Roof Applications Below Grade InstallationDownward Vertical Through-the-Roof InstallationMin 610 mm Venting Components Replacement of Ceramic Hearth Panels Glass CleaningOperating Instructions Glass InformationLava Rock Installation of Logs Ember Material PlacementFlame Characteristics Flame & Temperature AdjustmentInspecting the Venting System Top logs must be placed properly onto notchesCorrect flame appearance for DVBR36 model To Turn Off Gas To Heater Lighting and Operating InstructionsRemove window frame assembly before service work Troubleshooting Honeywell VS8421Troubleshooting the Gas Control System Valve Conversion Honeywell Valve Fuel Conversion InstructionsNatural Gas Pilot Conversion PSEPilot Conversion SIT Cleaning the Standing Pilot Control System MaintenanceBurner and Burner Compartment Brass TrimDescription DVBR36/42DVBR36/42 Remote Controls Optional AccessoriesOptional Fk-12 Fan Hook-up Ceramic Refractory PanelsDecorative Frame Trims Decorative Glass PanelsDecorative Face Kit Model Beam ColorDvbr Series Direct Vent Gas Fireplace Dvbr Series Direct Vent Gas Fireplace Limited Lifetime Warranty CFM Corporation