Dremel 6300 manual Scraping, Sanding, Grit Application, Metal, plaster and other, Surfaces

Page 12

DM 2610958399 07-08.qxp 8/6/08 2:15 PM Page 12

surface of a wall or corner. This can be accomplished by ensuring that the segmented portion of the blade is facing the wall or corner.

SCRAPING

Scrapers are suitable for removing old coats of varnish or adhesives, removing bonded carpeting, e.g. on stairs/steps and other small/medium size surfaces.

Select low to medium speed.

Rigid scrapers are for large area

removal, and harder materials such as vinyl flooring, carpeting and tile adhesives. When

removing strong, tacky adhesives, grease the

scraper blade surface with (petroleum jelly or silicone grease) to reduce gumming up.

The carpet/vinyl flooring removes easier if it is scored prior to removal so the scraper blade can move underneath the flooring material.

Flexible scrapers are used for hard to reach areas and softer material such as caulk.

Mount the scraper blade with the logo side facing up. With the flexible scraper, make sure that the screw head does not make contact with surface during the scraping process (a 30

-45 degree pitch is recommend). This can be accomplished by making sure that the tool is at an angle to the blade. You should be able to see the blade flex during the scraping process.

If you are removing caulk from a delicate surface such as a bath tub or tile back splash, we recommend taping or protecting the surface that the blade will rest on. Use rubbing alcohol to clean the surface after the caulk and/or adhesive is removed.

Turn the tool on and place desired accessory on the area where material is to be removed.

Begin with light pressure. The oscillating motion of accessory only occurs when pressure is applied to the material to be removed.

Excessive pressure can gouge or damage the background surfaces (e.g,. wood, plaster).

SANDING

Sanding accessories are suitable for dry sanding of wood, metal, surfaces, corners and edges and

hard to reach areas.

Work with the complete surface of the sanding pad, not only with the tip.

Corners may be finished using the tip or edge of the selected accessory, which should occasionally be rotated during use to distribute the wear on the accessory and backing pad surface.

Sand with a continuous motion and light pressure. DO NOT apply excessive pressure - let the tool do the work. Excessive pressure will result in poor handling, vibration, and unwanted sanding marks and premature wear on the sanding sheet.

Always be certain that smaller workpieces are securely fastened to a bench or other support. Larger panels may be held in place by hand on a bench or sawhorses.

Open-coat aluminum oxide sanding sheets are recommended for most wood or metal sanding applications, as this synthetic material cuts quickly and wears well. Some applications, such as metal finishing or cleaning, require special abrasive pads which are available from your dealer. For best results, use Dremel sanding accessories which are of superior quality and are carefully selected to produce professional quality results with your oscillating tool.

The following suggestions may be used as a general guide for abrasive selection, but the best results will be obtained by sanding a test sample of the workpiece first.

Grit

Application

Coarse

For rough wood or metal

 

sanding, and rust or old

 

finish removal.

Medium

For general wood or metal

 

sanding

Fine

For final finishing of wood,

 

metal, plaster and other

 

surfaces.

With the workpiece firmly secured, turn tool on as described above. Contact the work with the tool after the tool has reached its full speed, and remove it from the work before switching the tool off. Operating your oscillating tool in this manner will prolong switch and motor life, and greatly increase the quality of your work.

Move the oscillating tool in long steady strokes parallel to the grain using some lateral motion to overlap the strokes by as much as 75%. DO NOT apply excessive pressure - let the tool do the work. Excessive pressure will result in poor handling, vibration, and unwanted sanding marks.

-12-

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Leer antes de usar For English Version Version françaiseSee Ver la páginaGeneral Power Tool Safety Warnings Work area safetyElectrical safety Personal safetyPower tool use and care ServiceMany accidents are caused by poorly maintained power tools Edges are less likely to bind and are easier to controlSafety Rules for Oscillating Tools SharpSymbols Symbol Name Designation/ExplanationFunctional Description and Specifications Model 6300 Multi-Max Oscillating Power ToolMeasures reduce the risk of starting the tool accidentally Model numbe rAssembly Installing and Removing AccessoriesInstalling and Removing Sanding Sheets Blade Washer HEX Accessorykey Clamping Screw HEX KEYIntroduction Operating InstructionsIntended USE Learning to USE the ToolSlide ON/OFF Switch Switch SettingElectronic Feedback Variable Speed Control DialMulti-Max Accessory Speed Settings Use only Dremel, high-performance accessoriesOperating Applications ApplicationCutting Grout RemovalScraping SandingGrit Application Metal, plaster and otherSelecting Sanding/Grinding Sheets GrindingDM 2610958399 07-08.qxp 8/6/08 215 PM Maintenance Information CleaningCertain cleaning agents ! Caution and solvents damage Extension CordsMulti-Max Accessories MM70PMM70W Dremel Limited Warranty Dremel Service Center 4915 21st StreetUnited States Racine, WISécurité du lieu de travail Sécurité électriqueSécurité personnelle Utilisation et entretien des outils Électroportatifs EntretienConsignes de sécurité pour les outils oscillants Très tranchantsLe plomb provenant des peintures à base de plomb Symboles Symbole Nom Désignation/ExplicationDescription fonctionnelle et spécifications Outil électrique oscillant Multi-Max modèleNuméro de modèle 6300 Régime à videInstallation ET Retrait DES Feuilles DE Papier Abrasif AssemblagePorte VIS DE Fixation VIS DE Fixation CLÉ HexagonaleInstructions dutilisation Utilisations PrévuesApprenez À Vous Servir DE CET Outil FEED-BACK Électronique Réglage du sélecteurAcier Applications pour lemploi CoupeEnlèvement DU Coulis Raclage PonçageSélection des feuilles de ponçage/meulage MeulageDM 2610958399 07-08.qxp 8/6/08 215 PM Renseignements sur l’entretien Cordons de rallongeNettoyage ’EXISTE ’INTÉRIEUR AucuneAccessoire Matériau Application MM11 HCS = Acier à teneur élevée en carbone BiM = bimétalliqueGarantie limitée de Dremel ÉTATS-UNISCanada Scarborough, OntSeguridad del área de trabajo Seguridad eléctricaSeguridad personal Mecánicas Servicio de ajustes y reparacionesNormas de seguridad para herramientas oscilantes Símbolos Símbolo Nombre Designación/explicaciónCon aislamiento doble De Li-ionDescripción funcional y especificaciones Herramienta eléctrica oscilante Multi-Max modeloNúmero de modelo 6300 Velocidad sin carga Tensión nominal 120 50 60HzEnsamblaje Tornillo DE Llave Sujeción HexagonalIntroducción Instrucciones de utilizaciónGracias por comprar la herramienta Dremel Multi- Max USO PrevistoDeslizante Retroalimentación ElectrónicaAjustes de velocidad de los accesorios Multi-Max Dura PintadaAplicaciones de operación AplicaciónCorte Remoción DE LechadaRascado LijadoGrano Aplicación Selección de hojas de lija/amolado AmoladoMaterial Aplicación Papel de lija blancoDM 2610958399 07-08.qxp 8/6/08 216 PM Información de mantenimiento ServicioLimpieza Escobillas DE CarbonoAccesorios Multi-Max Accesorio Material Aplicación MM11HCS = Acero rico en carbono BiM =Bimetálica Garantía limitada de Dremel Estados UnidosCanadá DM 2610958399 07-08.qxp 8/6/08 216 PM Remarques Notas

6300 specifications

The Dremel 6300 is a versatile rotary tool specifically designed for a wide range of DIY projects and crafts. Known for its compact size and lightweight design, the Dremel 6300 offers exceptional control and precision, making it an ideal choice for both beginners and experienced hobbyists. This innovative tool is part of the Dremel family, a brand synonymous with quality and durability in the realm of rotary tools.

One of the standout features of the Dremel 6300 is its variable speed control. This tool allows users to adjust the rotational speed between 5,000 to 35,000 RPM, facilitating different material handling and project requirements. Whether you are cutting through wood, grinding metal, or polishing delicate surfaces like glass, the ability to fine-tune the speed significantly enhances the tool's versatility.

Equipped with a powerful motor, the Dremel 6300 delivers consistent performance even under heavy use. This motor is engineered with advanced cooling technology that minimizes overheating and ensures longevity. The tool also boasts a flexible shaft attachment, allowing users to work in tight spaces and achieve greater maneuverability on intricate projects.

Dremel's Quick Change Chuck feature is another notable characteristic of the 6300 model. It enables users to change out accessories quickly and conveniently, which is essential for projects requiring multiple attachments. The tool is compatible with a vast array of Dremel attachments and accessories, from cutting and grinding bits to polishing pads and sanding drums, making it a truly versatile tool for any craftsperson.

Moreover, the ergonomic design of the Dremel 6300 provides a comfortable grip during extended use. This emphasis on user comfort ensures that the tool can be used for prolonged periods without causing fatigue. Additionally, the balanced weight distribution enhances stability, giving users more confidence when performing intricate tasks.

In summary, the Dremel 6300 is an excellent rotary tool that combines power, precision, and versatility. With its variable speed control, robust motor, flexible shaft, and user-friendly features, the Dremel 6300 is an essential addition to the toolkit of anyone who enjoys crafting or DIY projects. Whether you are a seasoned professional or just starting, the Dremel 6300 will help unlock your creative potential.
Top Page Image Contents