Frigidaire FGES3065PF Removing and Replacing the Oven Door, Care And Cleaning, Door hinge locks

Page 49

Removing and Replacing the Oven Door

Removing and Replacing the Oven Door

CAUTION

The door is heavy. For safe, temporary storage, lay the door flat with the inside of the door facing down.

To remove oven door:

1.Open oven door completely, horizontal with floor (See Figure 43).

2.Pull the door hinge locks on both left and right door hinges down from the oven frame completely towards the oven door (See Figure 44). A tool such as a small flat-blade screwdriver may be required.

3.Firmly grasp both sides of oven door along the door sides. Do not use the oven door handle (See Figure 45).

4.Close the door to approximately 10 degrees from the door frame (See Figure 45).

5.Lift the oven door hinge arms over the roller pins located on each side of the oven frame (See Figure 46).

To replace oven door:

1.Firmly grasp both sides of oven door along the door sides. Do not use the oven door handle (See Figure 45).

2.Holding the oven door at the same angle as the removal position, seat the hook of the hinge arm over the roller pins located on each side of the oven door frame (See Figure 45 and Figure 46). The hook of the hinge arms must be fully seated onto the roller pins.

3.Fully open the oven door, horizontal with floor (See Figure 43).

4.Push the door hinge locks up towards and into the oven frame on both left and right oven door hinges to the locked position (See Figure 44).

5.Close the oven door.

IMPORTANT

Special door care instructions - Most oven doors contain glass that can break. Do not close the oven door until all the oven racks are fully in place. Do not hit the glass with pots, pans, or any other object. Scratching, hitting, jarring, or stressing the glass may weaken its structure causing an increased risk of breakage at a later time.

CARE AND CLEANING

Oven door hinge locations

Figure 43: Door hinge location

	CK
O
L

Figure 44: Door hinge locks

about 10°

oven door

hinge

Figure 45: Holding door for removal

roller pin

hinge arm

Figure 46: Replacement and location of hinge arm and roller pin

49

Image 49

Contents Care and Cleaning TABLE OF CONTENTSSetting Surface Controls WarrantyNeed Help? PRODUCT RECORD AND REGISTRATIONProduct Registration Read this Use & Care ManualIMPORTANT SAFETY INSTRUCTIONS CAUTIONS AND WARNINGSTip Over Hazard IMPORTANT SAFETY INSTRUCTIONS IMPORTANT INSTRUCTIONS FOR USING YOUR COOKTOP IMPORTANT INSTRUCTIONS FOR CLEANING YOUR OVEN IMPORTANT INSTRUCTIONS FOR USING YOUR OVENSELF-CLEANING OVENS FOR GLASS COOKTOP ONLYFor ovens to be wired into a junction box For models factory-equipped with a power cordGROUNDING INSTRUCTIONS Using Proper Cookware BEFORE SETTING SURFACE CONTROLSCookware Material Types Figure 1 Testing cookwareFigure 3 Element ON indicator light locations Element ON & hot surface indicator lightsAbout the Ceramic Glass Cooktop About the Radiant Surface ElementsThe available ESEC display settings The electronic surface element control ESEC some modelsESEC hot element indicator message HE Figure 6 Hot element indicator message ESEC power failure indicatorCooktop Sabbath Day Feature and Sb Message ESEC error indicator message ErHome Canning Surface cooking settings SETTING SURFACE CONTROLSTable 1 Recommended settings for surface elements SettingFigure 8 Control knob shown is typical only Single radiant surface elements all modelsTo Operate the Single Radiant Surface Elements To Operate the Dual Surface Element Dual Surface Radiant Element all modelsFigure 9 Inner coil operation L and inner/outer coil operation R SETTING SURFACE CONTROLS Figure 10 Single L, double M, and Triple R Triple Surface Radiant Element some modelsTo Operate the Triple Surface Element Figure 11 Triple radiant elementSETTING SURFACE CONTROLS To Operate the Bridge Radiant Element Bridge surface radiant element some modelsTable 2 Warm zone recommended food settings Keep warm zone some modelsTo Set the keep warm zone control Keep warm zone temperature selectionOven vent location BEFORE SETTING OVEN CONTROLSType of oven racks Removing, replacing, and arranging flat or offset oven racksrack connector bracket Effortless Oven Rack systemdoor connector bracket Figure 17 Connector arm/door connectionEnd should point up, as explained in Step connector arm Figure 19 Effortless oven rack after assemblyconnector door connectorOVEN CONTROLS Oven Controls Featuresbake convect broilSetting 12 or 24 Hour Time of Day Display Setting the ClockTable 3 Minimum and maximum control settings FeatureSetting Control for Silent Operation Setting Continuous Bake or 6 Hour Energy SavingSetting the Timer Temperature Display Fahrenheit/CelsiusSetting Preheat Setting Oven Lockout FeatureOven Light To activate the oven lockout featureTo set the bake temperature to 375F Setting BakeTo change the bake temperature example changing from 375F to 425F Baking Tips For best bake resultsFigure 23 Broil accessories Setting BroilTo set a broil of 500F Table 4 Broiling recommendationsConvection Cooking Setting Convection BakeBenefits of convection cooking Figure 24 Air circulation in convection functionSetting Convection Broil Setting Convection ConvertTo set a convection broil temperature of 500F Convection broiling tipsTo set a convection roast temperature of 375F Setting Convection RoastConvection roasting tips Setting Delay Start Setting Bake Time8. Press delay start Setting My Favorites Recipe some models Setting WarmWarm tips To set warmFigure 27 Using the probe Cooking with Meat ProbeProper placement of probe in food Figure 28 Probe in thickest area of foodTo set probe Figure 32 Probe set to cancel cooking Probe too hot messageFigure 30 Probe set showing probe temperature Figure 31 Probe set to continue cookingTable 5 USDA recommended minimum internal cooking temperatures Setting Slow Cook some modelsFood Type Internal TempAdjusting Oven Temperature Restoring Factory Default SettingTo adjust the oven temperature lower To restore oven control to factory default settingsPower failure while using Sabbath feature Setting the Sabbath Feature For use on the JewishSabbath and Holidays Figure 34 Downward position Warmer Drawer Indicator Light Warmer Drawer some modelsWarm & Ready Drawer Arranging Warmer Drawer Rack PositionsTable 6 Warmer drawer recommended food settings Setting Warmer Drawer Professional ModelKeep warm drawer temperature selection Removing and Replacing the Warmer Drawer To remove the warmer drawer Figure 35 Removal proceduresTo replace keep warm drawer To set a steam clean cycle Steam CleanFigure 37 Steam clean selected 5. Press start Figure 38 Clean around the oven door gasketWhat to expect during self-cleaning Self-Cleaning OperationAdhere to the following cleaning precautions Figure 39 Clean around the oven door gasketWhen the self-clean cycle is completed Setting Self-Clean Cycle DurationTo stop or Interrupt a self-cleaning cycle Cleaning Various Parts of Your Range CARE AND CLEANINGSurface Type RecommendationControl panel Cooktop Cleaning Cooktop MaintenanceFigure 41 Cooktop cleaning Figure 40 Cooktop care For light to moderate soilFigure 42 Cleaning products to avoid General CleaningDo not use the following on the cooktop Aluminum foil and utensilsFigure 46 Replacement and location of hinge arm and roller pin Removing and Replacing the Oven DoorTo remove oven door To replace oven doorReplacing the oven interior light bulb Replacing the oven lightFigure 47 Wall oven Halogen light Oven Baking BEFORE YOU CALLBaking Problems and Solutions Baking ProblemsProblem Solutions to Common ProblemsSolution information see “Cooktop Maintenance” on page see “Cooktop Maintenance” on pagenance” on page Cannot move appliance easily. Appliance must be accessible for service WARRANTY