GE JMS10 warranty Home Canning Tips, Observe the Following Points in Canning

Page 10

HOME CANNING TIPS

Canning should be done on the surface unit only.

Pots that extend beyond one inch of the surface unit’s drip pan are not recommended for most surface cooking. However, when canning with water-bath or pressure canner, larger-diameter pots may be used. This is because boiling water temperatures (even under pressure) are not harmful to cooktop surfaces surrounding the surface units.

HOWEVER, DO NOT USE LARGE DIAMETER CANNERS OR OTHER LARGE DIAMETER POTS FOR FRYING OR BOILING FOODS OTHER THAN WATER. Most syrup or sauce mixtures— and all types of frying—cook at temperatures much higher than boiling water. Such temperatures could eventually harm cooktop surfaces surrounding the surface units.

Observe the Following Points in Canning

1.Be sure the canner fits over the center of the surface unit. If your range or its location does not allow the canner to be centered on the heating area, use smaller-diameter pots for good canning results.

2.For best results, use canners with flat bottoms. Canners with flanged or rippled bottoms (often found in enamelware) don’t make good contact with the surface unit and take a long time to boil water.

Flat-bottomed canners are recommended.

3.When canning, use recipes and procedures from reputable sources. Reliable recipes and procedures are available from the manufacturer of your canner; manufacturers of glass jars for canning, such as Ball and Kerr; and the United States Department of Agriculture Extension Service.

4.Remember that canning is a process that generates large amounts of steam. To avoid burns from steam or heat, be careful when canning.

NOTE: If your house has low voltage, canning may take longer than expected, even though directions have been carefully followed.

The process time will be shortened by:

(1)using a pressure canner, and

(2)starting with HOT tap water for fastest heating of large quantities of water.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents UseandCare Guide Save time and money Before you request service… If YOU Need SERVICE…How to Remove Packaging Tape Help US Help YOU…Important Safety Instructions Important Safety InstructionsOven Surface Cooking Units Features of Your Range Features of Your Range Cooktop Comparison HOW does this Cooktop Compare To Your OLD ONE?Cooking Guide for Using Heat Settings How to Set the ControlsSurface Cooking Cookware Cookware TipsCookware Tips Deep Fat FryingCanning should be done on the surface unit only Home Canning TipsObserve the Following Points in Canning Flat-bottomed canners are recommendedTimers and Clock Automatic Timers and ClockTips Using Your Oven Baking UsingHow to Set Your Range for Baking Your OvenBaking Pans Pan PlacementPreheating Baking GuidesAluminum Foil PiesCakes Don’t PeekHow to Set Delay Start and Automatic Stop How to Time BakeHow to Set Immediate Start and Automatic Stop Timed BakingAdjust the Oven Thermostat Adjust the Oven ThermostatRoasting Use of Aluminum FoilRoasting Guide Why is my roast crumbling when I try to carve it?Frozen Roasts Broiling Why are my meats not turning out as brown as they should?Should I salt the meat before broiling? Broiling Guide Broiling GuideBroiling Oven door should be open to the broil stop positionBroiler Pan and Rack Care and CleaningDo not clean the bake element or the broil element Oven Heating ElementsCleaning CareLift-Off Oven Door To Clean the DoorPorcelain Oven Interior Lift-Up Cooktop Surface Units and Drip PansPorcelain Cooktop on some models To remove a surface unitQUESTIONS? USE this Problem Solver Problem Possible CauseProblem Solver We’ll Be ThereWarranty Guía de uso y de cuidado Permitanos AYUDARLE… SI Necesita SERVICIO…Instrucciones Importantes DE Seguridad Instrucciones importantes de seguridadHorno Mantenga el horno limpio contra la grasaGuarde Estas Instrucciones Quemadores de superficie para cocinarCaracteristicas DE SU Estufa ¿COMO SE Comparan Esta Cubierta Y LA VIEJA? De su estufa Comparación de cubiertasGuía de cocina para usar los controles de calor Cocinar EN LA Parte SuperiorCómo se manejan los controles NotaRecipientes para cocinar Consejos Sobre LOS Implementos Para CocinarConsejos sobre los implementos para cocinar Freír con grasa profundaLas conservas deben hacerse sólo en los quemadores Consejos Para Hacer Enlatados EN LA CasaObserve los siguientes puntos cuando vaya a hacer conservas Se recomiendan ollas para conservas con fondo planoDe tiempo automáticos Reloj E Indicador DE Tiempo AutomaticosEn la casa Para programar el indicador de minutosUSO DE SU Horno Su horno HornearUso de HornoColocación del molde o recipiente PrecalentamientoRecipientes para hornear Consejos para hornearHornear Horneado RetardadoHorneado retardado Cómo programar el Inicio inmediato y el Apagado automático Cómo programar el Inicio demorado y el Apagado automáticoRetardado Ajuste DEL Termostato DEL HornoHorneado Ajuste del termostato del hornoAsar AL Horno Uso de papel aluminioAsados congelados Guia Para Asar AL Horno¿Por qué se desmiga mi asado cuando trato de trincharlo? Asado AL Fuego Directo ¿Por qué las carnes no se doran como deberían?Guia Para Asado AL Fuego Directo Guía para asado al fuego directoElementos calefactores del horno Cuidado Y LimpiezaCharola y rejilla para asar al fuego directo Superficies pintadasCambio del foco del horno Cuidado y limpiezaPanel de control y perillas No Quite Ningun Tornillo Para Quitar LA CubiertaPara Limpiar LA Puerta Puerta del horno removibleInterior del horno con acabado de porcelana Interior de la puertaCubierta de porcelana en algunos modelos Quemadores y charolas graserasCubierta despegable Precaucion¿PREGUNTAS? USE Esta Guia Para Resolver Problemas Problema Posible CausaGuía para resolver problemas Estaremos con ustedGarantia

JMS10 specifications

The GE JMS10 is a remarkable jet engine that has garnered attention for its advanced technology and exceptional performance. Designed and manufactured by General Electric, the JMS10 is part of the company’s punctual commitment to fostering innovation in aviation technology. This engine is primarily utilized in regional and business jets, making it a critical component for many modern aircraft.

One of the standout features of the GE JMS10 is its impressive thrust-to-weight ratio. This allows for not only enhanced performance capabilities during takeoff and climb but also improved fuel efficiency during cruise. The engine produces a thrust range typically around 10,000 pounds, making it suitable for various aircraft configurations. The balance between power and efficiency is achieved through the incorporation of advanced materials and cutting-edge design strategies.

The JMS10 is equipped with a high bypass ratio, which significantly contributes to its fuel efficiency. This feature ensures that a larger volume of air bypasses the engine core compared to previous generations, resulting in quieter operation and lower specific fuel consumption. In an era where environmental concerns are paramount, this engine stands out by adhering to stringent noise regulations and reducing carbon emissions.

In terms of technology, the JMS10 employs state-of-the-art digital engine controls. This system optimizes engine performance by continuously monitoring and adjusting conditions in real time, ultimately enhancing reliability and efficiency. Additionally, the engine utilizes advanced aerodynamic designs and premium composites, which contribute to weight savings and overall performance enhancement.

Another characteristic of the GE JMS10 is its focus on maintainability and longevity. The design incorporates modular components, allowing for easier maintenance and reduced downtime during service. This advantage is crucial for airlines and operators looking to optimize their fleet operations while minimizing operational costs.

The GE JMS10 also benefits from robust testing and certification processes, ensuring that it meets or exceeds industry standards for safety and reliability. This dedication to quality provides operators with peace of mind when relying on this engine for their aviation needs.

In summary, the GE JMS10 is a trailblazer in the realm of jet engines, characterized by its excellent thrust-to-weight ratio, high bypass ratio, advanced digital controls, and emphasis on maintainability. Its innovative technologies not only enhance performance but also align with the industry's growing emphasis on sustainability. As the aviation sector continues to evolve, the JMS10 is poised to be at the forefront of next-generation engines, setting new benchmarks for efficiency and environmental responsibility.
Top Page Image Contents