GE JGB3001 Lower Control Panel Front Manifold Panel and Knobs, Oven Racks, Oven Light Replacement

Page 32

Care and cleaning of the range.

Lower Control Panel (Front Manifold Panel) and Knobs

Pull the knob straight off the stem.

It’s a good idea to wipe the control panel after each use of the oven. Use a damp cloth to clean or rinse. For cleaning, use mild soap and water or a 50/50 solution of vinegar and water. For rinsing, use clean water. Polish dry with a soft cloth.

Do not use abrasive cleansers, strong liquid cleaners, plastic scouring pads or oven cleaners on the control panel—they will damage the finish.

Do not bend knobs by pulling them up or down or by hanging a towel or other such loads. This can damage the gas valve shaft.

The control knobs may be removed for easier cleaning.

Make sure the knobs are in the Off positions and pull them straight off the stems for cleaning.

The knobs can be cleaned in a dishwasher or they may also be washed with soap and water. Make sure the insides of the knobs are dry before replacing.

Replace the knobs in the Off position to ensure proper placement.

Metal parts can be cleaned with soap

and water. Do not use steel wool, abrasives, ammonia, acids or commercial oven cleaners. Dry with a soft cloth.

Oven Racks

Clean the racks with an abrasive cleanser or scouring pad. After cleaning, rinse the racks with clean water and dry with a clean cloth.

If the racks ever become hard to slide, wipe the rack edges or oven rack supports with vegetable oil.

NOTE: Take the racks out of the oven before you begin the self-clean cycle or they may discolor.

InstructionsInstallation Care and Cleaning InstructionsOperating

Heavy-Duty Oven Racks (on some models)

Clean the racks with an abrasive cleanser.

To make the racks slide more easily, apply

The oven racks may be cleaned in the

a small amount of vegetable oil or cooking

oil to a paper towel and wipe the edges

self-cleaning oven. However, the racks

of the oven racks with the paper towel.

will darken in color, lose their luster

 

and become hard to slide if cleaned

 

during the self-cleaning cycle.

 

Troubleshooting Consumer Support Tips

Wire cover holder.

32

Oven Light Replacement

CAUTION: Before replacing your oven light bulb, disconnect the electrical power to the range at the main fuse or circuit breaker panel. Be sure to let the light cover and bulb cool completely.

The oven light bulb is covered with a removable glass cover that is held in place with a bail-shaped wire. Remove the oven door, if desired, to reach cover easily.

To remove:

Hold a hand under the cover so it doesn’t fall when released. With fingers of the same hand, firmly push back the wire cover holder. Lift off the cover.

Do not remove any screws to remove the cover.

Do not touch hot bulb with a wet cloth. Replace bulb with a 40-watt household appliance bulb.

To replace cover:

Place it into the groove of the light receptacle. Pull the wire forward to the center of the cover until it snaps into place. When in place, the wire holds the cover firmly. Be certain the wire

is in the depression in the center of the cover.

Connect electrical power to the range.

Page 31 Page 33
Image 32
Page 31 Page 33
Contents 49-85177 04-2010 GE Write the model and serial numbers here Model # Serial #Be secured by a properly installed anti-tip bracket. See Details before attempting to installTo reduce the risk of tipping the range, the range must Range within 4 inches. If it does not, the bracket must beIMPORTaNT SaFeTY NOTICe GEAppliances.comAppliance as a space heater to heat or SURFaCe BURNeRS Cook MeaT aND Poultry THOROUgHLY… Operating InstructionsOperatingInstructions Care and Cleaning ELeCTRIC WaRMINg DRaWeR on some modelsUsing the gas surface burners SafetyCare and Cleaning Installation Instructions Troubleshooting TipsCare Case of Power FailureTop-of-Range Cookware Using the oven controls Safety InstructionsInstallation Instructions CareSafety Instructions Or temperature by larger amountsTouch this pad to turn the oven light on or off Touch this pad to select the broil functionOven Vent Troubleshooting TipsBefore you begin… Support Using the upper ovenCare and Cleaning Installation Instructions How to Set the Oven for Broiling Place the meat or fish on a broiler grid in a broiler panHi Broil To change to Lo Broil, touchUsing the clock and timer. on some models CleaningTo Set the Timer To Set the ClockTo Reset the Timer To Cancel the TimerPower Outage Touch the Kitchen Timer On/Off pad twiceHow to Set an Immediate Start and Automatic Stop How to Set a Delayed Start and Automatic StopSpecial features of your oven control. on some models If you wish to turn OFF this feature, follow the steps belowUsing the Sabbath feature. on some models How to Set for Regular Baking/RoastingCare and Cleaning Installation Instructions Designed for use on the Jewish Sabbath and HolidaysHow to Exit the Sabbath Feature Touch the Clear/Off padAdjust the oven thermostat-Do it yourself Installation Troubleshooting InstructionsTipsTo Adjust the Thermostat on some models To Adjust the Thermostat on models with an Oven Temp KnobUsing the warming drawer. on some models When Using the Warming DrawerOn Signal Light Push and turn the control knob to any desired settingTo Warm Serving Bowls and Plates Temperature Selection ChartTo Crisp Stale Items Using the self-cleaning oven Before a Clean CycleHow to Set the Oven for Cleaning ConsumerAfter a Clean Cycle on some models How to Delay the Start of Cleaning on some modelsTo Stop a Clean Cycle on some models Care and cleaning of the range OperatingBurner Grates BurnersInstructions Installation Standard Twin Burner Assemblies on some modelsBurner Caps and Heads Tips Troubleshooting Operating InstructionsCooktop Surface Oven Air VentsTo clean the inside of the door Lift-Off Oven DoorOven Bottom Oven frame, pull them back outRemovable Warming Drawer on some models Removable Kick Panel on some modelsRemovable Storage Drawer on some models Oven Light Replacement Lower Control Panel Front Manifold Panel and KnobsOven Racks Do not remove any screws to remove the coverFoR yoUR SAFETy TooLS yoU wILL NeedMaterials yoU MAy Need Gas line shut-off valveInstallation Instructions DIMENSIoNS and Clearances For models JGB3000, JGB3001, JGB281, JGB300, JGB40028 to 281⁄4 CoNNECT the Range To GAS LoCATIoNPRoVIDE ADEqUATE GAS SUPPLy Range hookup Alternate Hookup Pressure regulator Manifold pipe An adapter may be used only on a 15-amp circuit Power cord of this appliance is equipped with aElectrical CoNNECTIoNS With LP gas, some yellow tipping on outer cones is normal Check oPERATIoN oF Surface BurnersSeal the oPENINGS Other Adjust the Bake and BRoILCheck oPERATIoN oF oVEN Burners Installing the ANTI-TIP Device WHEN ALL HooKUPS are CoMPLETEDBefore you call for service… Problem Possible Causes What To DoOven will not self-clean Oven temperature is too High to set a self-clean operationFood does not bake Oven controls improperly set Or roast properly Rack position is incorrectSelf-clean light on Oven Temp knob has not During self-clean cycleDoor appears Self-cleaning cycle has been During the self-cleaning cyclePower outage Power outage or surge Display goes blank Fuse in your home may beUnable to get Oven control pads were Display to show SF Not touched properlyAccessories Limited Time Offer! Free ShippingGE Will Replace What GE Will Not CoverFor The Period Warrantor General Electric Company. Louisville, KYWarrantor Mabe Canada Inc Burlington, Ontario Mabe Will ReplaceWhat Mabe Will Not Cover Schedule Service Consumer Support
Top Page Image Contents