GE JGB400, JGB3000, JGB3001, JGB281 Installing the ANTI-TIP Device, WHEN ALL HooKUPS are CoMPLETED

Page 44

Installation Instructions

9INSTALLING THE ANTI-TIP DEVICE

wARNING!

nRange must be secured with an approved Anti-Tip device.

nUnless properly installed, the range could be tipped by you or a child standing, sitting or leaning on an open door.

nAfter installing the Anti-Tip device, verify that

it is in place by carefully attempting to tilt the range forward.

nThis range has been designed to meet all recognized industry tip standards for all normal conditions.

nThe use of this device does not preclude tipping of the range when not properly installed.

nIf the Anti-Tip Device supplied with the range does not fit this application, use the Anti-Tip Device WB2X7909.

A. Mark the wall where the RIGHT EDGE of the range is to be located. Be sure to allow for the countertop overhang if you intend to install the range next to cabinets.

Anti-Tip

device

Slotted head screw

Wallplate Approx. 20°

21⁄8″

Marked edge

of range

B. Locate the outside edge of the device 21⁄8″ toward the center of the range from the marked edge of the range.

C. Using the device as a template, mark the position of the hole for the screw.

D. For wood construction, drill a pilot hole at an angle of 20 degrees from the horizontal. A nail or awl may be used if a drill is not available.

Mount the Anti-Tip device with the screw provided.

For cement or concrete construction, you will need

a 1/4″ x 11⁄2″ lag bolt and a 1/2″ O.D. sleeve anchor, which are not provided. Drill the recommended size hole for the hardware.

9INSTALLING THE ANTI-TIP DEVICE

(CoNT.)

Wallboard

Back of range

Anti-Tip device

Wood screw

Install the sleeve anchor into the drilled hole and then install the lag bolt through the device. The bolts must be properly tightened as recommended for the hardware.

E. Slide the range against the wall, and check for proper installation by grasping the front edge of the cooktop and carefully attempting to tilt the range forward.

The bracket should stop the range within 4 inches. If it does not, the bracket must be reinstalled.

wHEN ALL HooKUPS ARE CoMPLETED

Make sure all controls are left in the off position. Make sure the flow of combustion and ventilation air to the range is unobstructed.

CoNVERTING To LP GAS (or converting back to natural gas from LP)

This range leaves the factory set for use with natural gas. If you want to convert to LP gas, the conversion must be performed by a qualified LP gas installer.

The conversion instructions and LP orifices can be found attached to the range next to the pressure regulator.

Keep these instructions and the orifices in case you want to convert back to natural gas.

44

Page 43 Page 45
Image 44
Page 43 Page 45
Contents 49-85177 04-2010 GE Write the model and serial numbers here Model # Serial #Be secured by a properly installed anti-tip bracket. See Details before attempting to installTo reduce the risk of tipping the range, the range must Range within 4 inches. If it does not, the bracket must beIMPORTaNT SaFeTY NOTICe GEAppliances.comAppliance as a space heater to heat or SURFaCe BURNeRS Cook MeaT aND Poultry THOROUgHLY… Operating InstructionsOperatingInstructions Care and Cleaning ELeCTRIC WaRMINg DRaWeR on some modelsUsing the gas surface burners SafetyCare and Cleaning Installation Instructions Troubleshooting TipsCare Case of Power FailureTop-of-Range Cookware Using the oven controls Safety InstructionsInstallation Instructions CareSafety Instructions Or temperature by larger amountsTouch this pad to turn the oven light on or off Touch this pad to select the broil functionOven Vent Troubleshooting TipsBefore you begin… Support Using the upper ovenCare and Cleaning Installation Instructions How to Set the Oven for Broiling Place the meat or fish on a broiler grid in a broiler panHi Broil To change to Lo Broil, touchUsing the clock and timer. on some models CleaningTo Set the Timer To Set the ClockTo Reset the Timer To Cancel the TimerPower Outage Touch the Kitchen Timer On/Off pad twiceHow to Set an Immediate Start and Automatic Stop How to Set a Delayed Start and Automatic StopSpecial features of your oven control. on some models If you wish to turn OFF this feature, follow the steps belowUsing the Sabbath feature. on some models How to Set for Regular Baking/RoastingCare and Cleaning Installation Instructions Designed for use on the Jewish Sabbath and HolidaysHow to Exit the Sabbath Feature Touch the Clear/Off padAdjust the oven thermostat-Do it yourself Installation Troubleshooting InstructionsTipsTo Adjust the Thermostat on some models To Adjust the Thermostat on models with an Oven Temp KnobUsing the warming drawer. on some models When Using the Warming DrawerOn Signal Light Push and turn the control knob to any desired settingTo Warm Serving Bowls and Plates Temperature Selection ChartTo Crisp Stale Items Using the self-cleaning oven Before a Clean CycleHow to Set the Oven for Cleaning ConsumerAfter a Clean Cycle on some models How to Delay the Start of Cleaning on some modelsTo Stop a Clean Cycle on some models Care and cleaning of the range OperatingBurner Grates BurnersInstructions Installation Standard Twin Burner Assemblies on some modelsBurner Caps and Heads Tips Troubleshooting Operating InstructionsCooktop Surface Oven Air VentsTo clean the inside of the door Lift-Off Oven DoorOven Bottom Oven frame, pull them back outRemovable Warming Drawer on some models Removable Kick Panel on some modelsRemovable Storage Drawer on some models Oven Light Replacement Lower Control Panel Front Manifold Panel and KnobsOven Racks Do not remove any screws to remove the coverFoR yoUR SAFETy TooLS yoU wILL NeedMaterials yoU MAy Need Gas line shut-off valveInstallation Instructions DIMENSIoNS and Clearances For models JGB3000, JGB3001, JGB281, JGB300, JGB40028 to 281⁄4 CoNNECT the Range To GAS LoCATIoNPRoVIDE ADEqUATE GAS SUPPLy Range hookup Alternate Hookup Pressure regulator Manifold pipe An adapter may be used only on a 15-amp circuit Power cord of this appliance is equipped with aElectrical CoNNECTIoNS With LP gas, some yellow tipping on outer cones is normal Check oPERATIoN oF Surface BurnersSeal the oPENINGS Other Adjust the Bake and BRoILCheck oPERATIoN oF oVEN Burners Installing the ANTI-TIP Device WHEN ALL HooKUPS are CoMPLETEDBefore you call for service… Problem Possible Causes What To DoOven will not self-clean Oven temperature is too High to set a self-clean operationFood does not bake Oven controls improperly set Or roast properly Rack position is incorrectSelf-clean light on Oven Temp knob has not During self-clean cycleDoor appears Self-cleaning cycle has been During the self-cleaning cyclePower outage Power outage or surge Display goes blank Fuse in your home may beUnable to get Oven control pads were Display to show SF Not touched properlyAccessories Limited Time Offer! Free ShippingGE Will Replace What GE Will Not CoverFor The Period Warrantor General Electric Company. Louisville, KYWarrantor Mabe Canada Inc Burlington, Ontario Mabe Will ReplaceWhat Mabe Will Not Cover Schedule Service Consumer Support
Top Page Image Contents