Roland MMP-2 owner manual Patch Selection Select, Saving a Patch Store Patch

Page 15

Set Up and Basic Operations

Patch Selection (SELECT)

The alphabet character shown upper left side of the patch number is showing the status of patch.

(U) to be indicated if it is a user patch. (P) to be indicated if it is a preset patch.

You cannot customize the preset patch. But it is possible to customize the parameter of preset patch and save as a new user patch.

1. Press the [PATCH] button a number of times, until it lights in green. You are now in the mode where you can choose a patch.

2.Turn the left Value control to choose a patch.

3.Press the [ENTER] button to confirm your selection.

The patch currently selected will be shown at first in patch selection screen. If you turn around the knob, the status changes and let you select other patch. You will see the currently selected patch while turning around the knob. This to show the patch in saved status.

For example, once you select patch A and customize parameters, it is different from saved status of patch A. However, it isn't saved yet. If you turn around the knob and re-select patch A, the parameter before your customize will be shown.

Saving a Patch (STORE PATCH)

Save current status as a new user patch

*The patch stored in the memory area disappears and to be replaced by newly created patch.

*Only the user patch area will be shown as memory area.

1.Press the [PATCH] button a number of times, until it lights in red. You are now

in the mode where you can choose the destination for saving.

2.Turn the left Value control to choose the patch to serve as the destination for saving.

3.Use the center Value control to move the cursor, and use the right Value control to choose characters. Repeat this to enter the patch name.

4. Press [ENTER]. Your confirmation will be requested.

5.Re-press [ENTER]. The patch will be saved. Once the saving procedure is

completed, system go back to normal screen after indicating [Completed] on screen.

Resetting Effect Parameters (RESET)

This resets the effect parameter to the values shown below. This is the status with almost no effect. If you want to set effect parameter completely from zero, this shall be executed. You can apply this to all effects or to just one.

1.Press the [PATCH] button several times to display “RESET PATCH.” The button

lights up in orange.

2.Use the left Value control to choose the target effect or effects for the [RESET] operation. Choosing “ALL” resets all effects.

3.Press [ENTER]. Your confirmation will be requested.

Set Up and Basic Operations

15

Image 15
Contents Copyright 2002 Roland Corporation Page Using the Unit Safely Contents Settings for Digital Connections Additional Precautions Power SupplyPlacement MaintenanceCopyright Handling CD-ROMsMain Features Getting StartedChecking the Included Items Top Panel Top and Rear PanelsRear Panel Dynamics Function Organization and Signal FlowPad Sens EqualizerMaking the Connections Set Up and Basic OperationsGetting Ready to Switch on the Power Connecting the Power SourceConnecting the Output Equipment Setting the Output LevelTurning On the Power Connecting the Input DeviceSave pressing Enter button Adjusting the Contrast of the LCD Screen LcdcntGlobal Functions PatchesResetting Effect Parameters Reset Patch Selection SelectSaving a Patch Store Patch Dynamics CMP / EXP MetersEdit Channel Select Edit CH Select InputPad Settings for the Analog InputsPeak Indicator Phantom Power +48VAttenuator ATT Turning Off the PowerPhase Low-cut Filter LO-CUTReference Microphone Input Using EffectsMic Modeling Mic Modeling OFF/ON ModelEqualizer Filter Type Type DynamicsCompressor Gain GainRatio Ratio Compressor Type TypeKey In Channel KEY Threshold ThreshEnhancer/De-esser ExpanderPre-amp Modeling Plug-in EffectHarmonic BrightAudio Input Source Settings for Digital ConnectionsSampling Clock Source Sampling FrequencyExamples of Use Analog Input to Analog OutputAnalog Input to Digital Output Channel Linking Other FeaturesCopying Settings Between Channels Backup PatchInitializing RouteComputer settings Use of computer and setupSet up PC setting and Install MMP-2 settingsWindows Me Use the following procedure to install the MMP-2 driverDeleting the MMP-2 Driver WindowsUse of computer and setup Use the USB cable to connect the MMP-2 and your computer Macintosh / OMS Installing the MMP-2 DriverOMS settings USB connector USB cableUse of computer and setup Macintosh / FreeMIDI FreeMIDI settings About Quick Setup dialog box will appear. Click Continue Backup Patches Intuitive operation of MMP-2 using MMP-2 editorFunctions work in conjunction with computers MMP-2 settings p Trouble ShootingSymptom Cause Remedy Another patch Resetting Effect ParametersWindows users Trouble Shooting about ComputerMacintosh users Was the MMP-2 recognized? MMP-2 does not recover correctly from sleep modeCannot make USB connections correctly Macintosh hangs upTransmitted Data Midi ImplementationData Transfer Address Map Algorithm 1 MIC Modeling + Dynamics + Plug INPreamp Status Bulk Data Appendices Midi Implementation Chart Specifications Index SymbolsWindows Memo Memo Information Important Safety Instructions 02897523 ’02-2-E2-21KS About Input Jacks Limitations and Conditions of Condenser Microphone