Roland MMP-2 owner manual Trouble Shooting about Computer, Windows users

Page 43

Trouble Shooting about Computer

*Please read the “ReadMe” file in the MMP-2 Driver & Software CD-ROM. You can get any additional information not written in the owner’s manual from the “ReadMe” file.

Windows Users

p.43

Macintosh Users ....

p.44

Windows users

USB connections cannot be made correctly.

◆Has the MMP-2 been recognized?

Disconnect the USB cables, and then re-connect them.

It is possible that the computer has failed to recognize or initialize the MMP-2. Leave the USB cable connected to the MMP-2, and restart Windows. If connection still does not occur, exit Windows, and turn off the power of your computer. Then turn on the power of your computer and start Windows.

Cannot shift to Suspend*

◆Is an application which uses the MMP-2 running?

Exit the application which is using the MMP-2.

The computer cannot shift to Suspend mode if an application such as a sequencer is using the MMP-2.

What is Suspend?

This is a function which minimizes power consumption by shutting down the internal circuitry of the computer and the peripheral devices while the power remains supplied to the computer.

MMP-2 does not resume correctly from the suspended state

◆When suspended, was the MMP-2 still connected via the USB cable?

Disconnect the USB cable, and then re-connect it.

On some computers when Windows resumes from the suspended state, the MMP-2 may fail to resume. If this occurs, the USB cable connected to the MMP-2 should be disconnected and then reconnected.

Windows hangs up (freezes) when returning from the suspended state

Disconnect the USB cable before suspending.

On some computers when Windows resumes from the suspended state, it may hang up (freeze). If this occurs, the USB cable connected to the MMP-2 should be disconnected before suspending.

When you once again wish to use the MMP-2, make sure that the computer has resumed correctly from the suspend state, and then connect the USB cable to the MMP-2.

*If the computer itself has a suspend switch, the USB cable connected to the MMP-2 should be disconnected before you press that switch.

*For a notebook computer, some settings of the computer may cause it to automatically enter suspend mode when the lid (LCD display) is closed, so the USB cable connected to the MMP-2 should be disconnected before the lid is closed.

Does not work with Windows 95

It will not operate on Windows 95.

Trouble Shooting about Computer

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Copyright 2002 Roland Corporation Page Using the Unit Safely Contents Settings for Digital Connections Additional Precautions Power SupplyPlacement MaintenanceCopyright Handling CD-ROMsGetting Started Main FeaturesChecking the Included Items Top Panel Top and Rear PanelsRear Panel Dynamics Function Organization and Signal FlowPad Sens EqualizerMaking the Connections Set Up and Basic OperationsGetting Ready to Switch on the Power Connecting the Power SourceConnecting the Output Equipment Setting the Output LevelTurning On the Power Connecting the Input DeviceSave pressing Enter button Adjusting the Contrast of the LCD Screen LcdcntGlobal Functions PatchesPatch Selection Select Resetting Effect Parameters ResetSaving a Patch Store Patch Dynamics CMP / EXP MetersEdit Channel Select Edit CH Select InputPad Settings for the Analog InputsPeak Indicator Phantom Power +48VAttenuator ATT Turning Off the PowerPhase Low-cut Filter LO-CUTReference Microphone Input Using EffectsMic Modeling Mic Modeling OFF/ON ModelEqualizer Filter Type Type DynamicsCompressor Gain GainRatio Ratio Compressor Type TypeKey In Channel KEY Threshold ThreshEnhancer/De-esser ExpanderPre-amp Modeling Plug-in EffectHarmonic BrightAudio Input Source Settings for Digital ConnectionsSampling Clock Source Sampling FrequencyAnalog Input to Analog Output Examples of UseAnalog Input to Digital Output Channel Linking Other FeaturesCopying Settings Between Channels Backup PatchInitializing RouteComputer settings Use of computer and setupSet up PC setting and Install MMP-2 settingsWindows Me Use the following procedure to install the MMP-2 driverDeleting the MMP-2 Driver WindowsUse of computer and setup Use the USB cable to connect the MMP-2 and your computer Macintosh / OMS Installing the MMP-2 DriverOMS settings USB connector USB cableUse of computer and setup Macintosh / FreeMIDI FreeMIDI settings About Quick Setup dialog box will appear. Click Continue Intuitive operation of MMP-2 using MMP-2 editor Backup PatchesFunctions work in conjunction with computers MMP-2 settings p Trouble ShootingSymptom Cause Remedy Another patch Resetting Effect ParametersWindows users Trouble Shooting about ComputerMacintosh users Was the MMP-2 recognized? MMP-2 does not recover correctly from sleep modeCannot make USB connections correctly Macintosh hangs upTransmitted Data Midi ImplementationData Transfer Address Map Algorithm 1 MIC Modeling + Dynamics + Plug INPreamp Status Bulk Data Appendices Midi Implementation Chart Specifications Index SymbolsWindows Memo Memo Information Important Safety Instructions 02897523 ’02-2-E2-21KS About Input Jacks Limitations and Conditions of Condenser Microphone
Top Page Image Contents