Roland MMP-2 owner manual Data Transfer Address Map

Page 47

MIDI Implementation

Data Set (DT1)

Input Parameters

Status

Data Bytes

 

Status

F0H

 

41H,Dev,00H,4EH,12H,aaH,bbH,ccH,ddH, ..., eeH,Sum

F7H

Byte

 

Description

 

 

F0H

 

Status of System Exclusive Message

 

41H

 

Manufacturer ID

 

(Roland)

Dev

 

Device ID

 

 

00H

4EH

Model ID

 

(MMP-2)

12H

 

Command ID

 

(DT1)

aaH

 

Address MSB

 

 

bbH

 

Address MID

 

 

ccH

 

Address LSB

 

 

ddH

 

Data

 

 

:

 

:

 

 

eeH

 

Data

 

 

Sum

 

Check Sum

 

 

F7H

 

EOX

(End of System Exclusive Message)

The message is received under the following condition.

If the device ID on the message is same as that of the receive device, and the address on the message correspond to the specified parameter base address, the received data are stored from the specified parameter base address.

If the interval of received messages is shorter than 25m sec., the MMP-2 can not work the receive message procedure correctly.

The message is transmitted under the following condition.

+————————————————————————————————————————————————————————————————————————+

Start

 

 

Address

Data

Contents and Remarks

==========+=========+===================================================

01 00 00 — 01 Phantom Power 1OFF, ON ——————————+—————————+———————————————————————————————————————————————————

01 01 16 — 46 ATT 1(0dB:40H) —42 — +6dB ——————————+—————————+———————————————————————————————————————————————————

01 02 00 — 01 Phase 1NORMAL, INVERT ——————————+—————————+———————————————————————————————————————————————————

01 03 00 (Reserved) ——————————+—————————+———————————————————————————————————————————————————

01 04 00 — 51 LO—Cut 1TURU,20 — 2.00kHz ——————————+—————————+———————————————————————————————————————————————————

01

05

00

(Reserved)

 

:

 

:

 

 

01

0F

00

(Reserved)

——————————+—————————+———————————————————————————————————————————————————

01 10 00 — 01 Phantom Power 2OFF, ON ——————————+—————————+———————————————————————————————————————————————————

01 11 16 — 46 ATT 2(0dB:40H) —42 — +6dB ——————————+—————————+———————————————————————————————————————————————————

01 12 00 — 01 Phase 2NORMAL, INVERT ——————————+—————————+———————————————————————————————————————————————————

01 13 00 (Reserved) ——————————+—————————+———————————————————————————————————————————————————

01 14 00 — 51 LO—Cut 2TURU,20 — 2.00kHz ——————————+—————————+———————————————————————————————————————————————————

01

15

00

(Reserved)

 

:

 

:

 

 

01

7F

00

(Reserved)

——————————+—————————+———————————————————————————————————————————————————

When the MMP-2 transmit the data on the requested parameter after receiving the Data Request message(RQ1).

See “Data Transfer Address Map” (p. 47) for more details of the transfer parameters.

Data Transfer Address Map

The each address value is expressed as a 7bit hex number.

+————————————————————————————————————————————————————————————————————————+

Address MSB LSB —————————————————————+————————————————+————————————————+————————————————+

Binary

0aaa aaaa

0bbb bbbb

0ccc cccc

7—bit Hex

AA

BB

CC

+————————————————————————————————————————————————————————————————————————+

Parameter Address Block

<Model ID = 00H 4EH>

+————————————————————————————————————————————————————————————————————————+

Start

 

Address

Contents and Remarks

==========+=============================================================

00 00 00 System Parameter ——————————+—————————————————————————————————————————————————————————————

00 01 00 Input Parameter ——————————+—————————————————————————————————————————————————————————————

00 02 00 Effect Parameter (Temp) ——————————+—————————————————————————————————————————————————————————————

00 04 00 Status ——————————+—————————————————————————————————————————————————————————————

00 05 00 Remote Operation ——————————+—————————————————————————————————————————————————————————————

01 00 00 Bulk Data ——————————+—————————————————————————————————————————————————————————————

System Parameter

+————————————————————————————————————————————————————————————————————————+

Start

 

 

Address

Data

Contents and Remarks

==========+=========+===================================================

00 00 00 - 01 Master Clock(*1)INTERNAL, DIGITAL ——————————+—————————+———————————————————————————————————————————————————

00 01 00 - 03 Sampling Frequency(*1) 44.1K,48K,88.2K,96KHz ——————————+—————————+———————————————————————————————————————————————————

00 02 00 - 01 Audio Source(*1)MIC, DIGITAL ——————————+—————————+———————————————————————————————————————————————————

00

03

00

(Reserved)

 

:

 

:

 

 

00

0F

00

(Reserved)

——————————+—————————+———————————————————————————————————————————————————

00 10 00 - 01 USB Driver(*1)VENDER, GENELIC ——————————+—————————+———————————————————————————————————————————————————

00 11 00 - 1F MIDI Device ID(*1)1,,,32 ——————————+—————————+———————————————————————————————————————————————————

00 12 00 - 01 MIDI Level Meter Tx. SwitchOFF,ON ——————————+—————————+———————————————————————————————————————————————————

00

13

00

(Reserved)

 

:

 

:

 

 

00

1F

00

(Reserved)

——————————+—————————+———————————————————————————————————————————————————

00 20 00 - 0F LCD Contrast1,,,16 ——————————+—————————+———————————————————————————————————————————————————

00 21 00 - 02 Peak Level Select-6,-3,0dB ——————————+—————————+———————————————————————————————————————————————————

00 22 00 - 02 Effects RoutingNORM,P IN,P OUT ——————————+—————————+———————————————————————————————————————————————————

00

23

00

(Reserved)

 

:

 

:

 

 

00

7F

00

(Reserved)

——————————+—————————+——————————————————————————————————————————————————— (*1)Read Only Parameters.

Effect Parameters

Basic Address

+————————————————————————————————————————————————————————————————————————+

Start

 

 

Address

Data

Contents and Remarks

==========+=========+===================================================

02

00

20

— 7F

Effects

Patch Name — 1

(ASCII)

:

 

 

:

 

 

:

02

0B

20

7F

Effects

Patch Name —12

——————————+—————————+———————————————————————————————————————————————————

02 0C 10 — 11 Effects Algorithm

Number

 

10H: MIC

MODEL

+

4 BAND

EQ + DYNAMICS

11H: MIC

MODEL

+

DYNAMICS + PLUG IN(Preamp)

——————————+—————————+———————————————————————————————————————————————————

02

0D

00

(Reserved)

 

:

 

:

 

 

02

0F

00

(Reserved)

——————————+—————————+———————————————————————————————————————————————————

02

10

00

7F

Effects Parameters

:

 

 

:

 

03

7F

00

7F

+————————————————————————————————————————————————————————————————————————+

Algorithm 0 (MIC MODELING + 4 BAND EQ + DYNAMICS)

+————————————————————————————————————————————————————————————————————————+

Start

 

 

Address

Data

Contents and Remarks

==========+=========+===================================================

02 10 00 — 01 LINKOFF, ON ——————————+—————————+———————————————————————————————————————————————————

02 11 00 (Reserved) ——————————+—————————+———————————————————————————————————————————————————

02 12 00 — 01 Bypass MODEL 1OFF, ON ——————————+—————————+———————————————————————————————————————————————————

02 13 00 — 01 Bypass MODEL 2OFF, ON ——————————+—————————+———————————————————————————————————————————————————

02 14 00 — 01 Bypass EQ 1OFF, ON ——————————+—————————+———————————————————————————————————————————————————

02 15 00 — 01 Bypass EQ 2OFF, ON ——————————+—————————+———————————————————————————————————————————————————

02 16 00 — 01 Bypass DYN 1OFF, ON ——————————+—————————+———————————————————————————————————————————————————

02 17 00 — 01 Bypass DYN 2OFF, ON ——————————+—————————+———————————————————————————————————————————————————

02

18

00

(Reserved)

 

:

 

:

 

 

02

1F

00

(Reserved)

——————————+—————————+———————————————————————————————————————————————————

02 20 00 — 01 MODEL 1: SWOFF, ON ——————————+—————————+———————————————————————————————————————————————————

02 21

00 — 05

MODEL 1: Input

0,,,5 =

 

DR—20,SmlDy,HedDy,MinCn,Flat,AKGC3K

——————————+—————————+———————————————————————————————————————————————————

02 22

00 — 06

MODEL 1: Output 0,,,6 =

SML.DY,VOC.DY,LRG.DY,SML.CN,LRG.CN,VNT.CN,FLAT

——————————+—————————+———————————————————————————————————————————————————

02 23 34 — 4C MODEL 1: Proximity Effect (0:40H) —12,,,+12 ——————————+—————————+———————————————————————————————————————————————————

02 24 00 — 6B MODEL 1: Timelag0,,,107 = 0,,,3000cm ——————————+—————————+———————————————————————————————————————————————————

02 25 00 — 01 MODEL 2: SWOFF, ON ——————————+—————————+———————————————————————————————————————————————————

02 26

00 — 05

MODEL 2: Input

0,,,5 =

 

DR—20,SmlDy,HedDy,MinCn,Flat,AKGC3K

——————————+—————————+———————————————————————————————————————————————————

02 27

00 — 06

MODEL 2: Output 0,,,6 =

SML.DY,VOC.DY,LRG.DY,SML.CN,LRG.CN,VNT.CN,FLAT

——————————+—————————+———————————————————————————————————————————————————

02 28 34 — 4C MODEL 2: Proximity Effect (0:40H) —12,,,+12 ——————————+—————————+———————————————————————————————————————————————————

02 29 00 — 6B MODEL 2: Timelag0,,,107 = 0,,,3000cm ——————————+—————————+———————————————————————————————————————————————————

02

2A

00

(Reserved)

 

:

 

:

 

 

02

2F

00

(Reserved)

——————————+—————————+———————————————————————————————————————————————————

02 30 00 — 01 EQ 1: SWOFF, ON ——————————+—————————+———————————————————————————————————————————————————

02 31 16 — 46 EQ 1: ATT

(0dB:40H) —42 — +6dB

47

Image 47
Contents Copyright 2002 Roland Corporation Page Using the Unit Safely Contents Settings for Digital Connections Additional Precautions Power SupplyPlacement MaintenanceCopyright Handling CD-ROMsChecking the Included Items Main FeaturesGetting Started Top Panel Top and Rear PanelsRear Panel Dynamics Function Organization and Signal FlowPad Sens EqualizerMaking the Connections Set Up and Basic OperationsGetting Ready to Switch on the Power Connecting the Power SourceConnecting the Output Equipment Setting the Output LevelTurning On the Power Connecting the Input DeviceSave pressing Enter button Adjusting the Contrast of the LCD Screen LcdcntGlobal Functions PatchesSaving a Patch Store Patch Resetting Effect Parameters ResetPatch Selection Select Dynamics CMP / EXP MetersEdit Channel Select Edit CH Select InputPad Settings for the Analog InputsPeak Indicator Phantom Power +48VAttenuator ATT Turning Off the PowerPhase Low-cut Filter LO-CUTReference Microphone Input Using EffectsMic Modeling Mic Modeling OFF/ON ModelEqualizer Filter Type Type DynamicsCompressor Gain GainRatio Ratio Compressor Type TypeKey In Channel KEY Threshold ThreshEnhancer/De-esser ExpanderPre-amp Modeling Plug-in EffectHarmonic BrightAudio Input Source Settings for Digital ConnectionsSampling Clock Source Sampling FrequencyAnalog Input to Digital Output Examples of UseAnalog Input to Analog Output Channel Linking Other FeaturesCopying Settings Between Channels Backup PatchInitializing RouteComputer settings Use of computer and setupSet up PC setting and Install MMP-2 settingsWindows Me Use the following procedure to install the MMP-2 driverDeleting the MMP-2 Driver WindowsUse of computer and setup Use the USB cable to connect the MMP-2 and your computer Macintosh / OMS Installing the MMP-2 DriverOMS settings USB connector USB cableUse of computer and setup Macintosh / FreeMIDI FreeMIDI settings About Quick Setup dialog box will appear. Click Continue Functions work in conjunction with computers Backup PatchesIntuitive operation of MMP-2 using MMP-2 editor MMP-2 settings p Trouble ShootingSymptom Cause Remedy Another patch Resetting Effect ParametersWindows users Trouble Shooting about ComputerMacintosh users Was the MMP-2 recognized? MMP-2 does not recover correctly from sleep modeCannot make USB connections correctly Macintosh hangs upTransmitted Data Midi ImplementationData Transfer Address Map Algorithm 1 MIC Modeling + Dynamics + Plug INPreamp Status Bulk Data Appendices Midi Implementation Chart Specifications Index SymbolsWindows Memo Memo Information Important Safety Instructions 02897523 ’02-2-E2-21KS About Input Jacks Limitations and Conditions of Condenser Microphone