Crane Merchandising Systems 673, 677, 675 manual SureVend Configuration HDC II Programming Guide

Page 49

SureVend Configuration

HDC II Programming Guide

 

SET UP THE SUREVEND™ ANTI-JACKPOT TIMER

1. Press

then

until the display shows

. XX

represents how many minutes SureVend™ will be disabled for either cup ring. The same value applies to the two timers (one on each ring).

2.Enter a number using either keypad.

 

 

 

 

 

AJP.TMRXXM

 

If any cup ring motor fails to deliver a cup on two consecutive attempts, the

 

cup ring goes out of service. After the time set in step 2 has elapsed, the

 

cup ring goes back in service and is given one more chance to deliver a cup.

 

If cup delivery is again unsuccessful, the ring goes out of service until the

 

machine is serviced. A successful delivery on any cup ring will reset the

 

failed attempts for that particular cup ring. If both cup rings perform three

 

consecutive failed attempts (and the SureVend™ sensor is determined to be

 

working), the entire machine goes in the "mug only" mode until the

 

machine is serviced. If either cup ring performs three consecutive failed

 

attempts with the other cup ring in anti-jackpot timer mode, the entire

 

machine will be in "mug only" mode (assuming SureVend is working) until

 

the preset time elapses (one more attempt will be made to deliver a cup) or

 

the machine is serviced by a route operator.

 

 

 

 

 

 

 

NOTE

 

 

 

 

A setting of

will disable this feature. A setting of

will

 

 

 

00

 

 

99

 

 

 

disable the ring until the next service call.

 

 

 

 

 

 

CONDITIONS:

 

 

 

 

If the cup sizes are the same, the machine alternates ring motor cycles until

 

either a cup is detected or both rings reach two consecutive failed attempts.

 

If the cup sizes are different, the selected ring is cycled up to two times

 

before returning credit. If the customer selects a large size drink and that

 

ring is out of service, the customer gets a small drink (if in service) and

 

receives change.

 

 

 

 

 

 

 

 

 

 

 

 

 

VIEW SOFTWARE VERSION

 

 

 

1.

Press

, and press

until the display shows

 

.

 

"XXXXXX" represents the current software version number.

XXXXXXJuly, 2003

2.

CONTINUE.

 

 

 

VER

6730018

 

 

43

 

Page 48 Page 50
Image 49
Page 48 Page 50
Contents Page Crane Merchandising Systems Parts and Support Phone Numbers Table of Contents SureVend Configuration View Machine Data Test the Machine Getting around Introduction HDC II Programming GuideDisplays HDC II Programming Guide IntroductionFunction Keys Other KeysHelpful Hint Some ConventionsPress this button to Control Panel Switch Functions ExplainedSurevend Supervisor Mode Gain Access to the Supervisor Mode Basic Setup HDC II Programming GuideEnter a NEW Supervisor Code Enter a Freevend CodeEnter a NEW Data Recall Code HDC II Programming Guide Basic SetupUsage Lock or Unlock Mode or Payout Keys SET Printer or DEX Options Printer Mode onlySelect Printer Baud Rate SET DEX Options DEX Mode only SET Talker Mode HDC II Programming Guide Monetary SetupSelect Display Language Select Coin MechanismBill Selection Method Monetary Setup HDC II Programming GuideOFF Initial Setup of a NON-STANDARD Bill ValidatorSelect Monetary Options Select Card ReaderACC FFN Advanced Options SET UP Winner ModeSET UP MUG Discount Cup Configuration HDC II Programming GuideAN Example Press HDC II Programming Guide Cup ConfigurationDual Brew CONTINUE.LK.ABCDEFGH Disable Selections in the MerchandiserSET UP CUP Sizes 0X2 Assign CUP Sizes to Selections Supervisor Mode onlySET UP a HOT Drink Set up a Hot Drink HDC II Programming GuideDifferences HDC II Programming Guide Set up a Hot DrinkOptions Collecting Condiment Throws Collecting DRY Product Gram ThrowsEspresso = Chocolate times for cappuccino Collecting HOT Water Throws This water is HOT! Be carefulTable W1 Water Throw Default Times and Volumes Cappuccino RecipesEnter the Supervisor Code Caffé LatteSET the Machine to Vend a Large D Selection SET UP Your Selection European Cappuccino +WXYZBlended Selections BlendSET UP LOW Temperature Dispensing View or SET the HOT Water Tank TemperatureSET UP LOW Power Settings OfserviceOFF SET the Automatic Brewer Rinse TimeSET the Bowl Rinse Time RINTurn Surevend on or OFF HDC II Programming Guide SureVend ConfigurationOptional or Mandatory Surevend SET UP the Surevend ANTI-JACKPOT Timer SureVend Configuration HDC II Programming GuideView Software Version SET the Time of DAY HDC II Programming Guide Setup TimeSET MONTH, DATE, and Year SET Daylight Savings OptionSET TIME-OF-DAY Inhibit Vending Setup Time HDC II Programming GuideSET TIME-OF-DAY Free Vending SET TIME-OF-DAY Discount VendingInhibit Freevend Discount Time Interval EditingMWF Select a Standby Message Select AN OUT-OF-SERVICE MessageSelect a Freevend Message Shortcut Messages HDC II Programming GuideEND of Message Character Entering Your Message JhgiView Water Tank Temperature Check the Setup HDC II Programming GuideView Machine TYPE/CONFIGURATION Setting View CUP Sizes Assigned to Selections HDC II Programming Guide Check the SetupPayout Coins View Machine Data HDC II Programming Guide View Nonresettable Sales and Vend DataSET Prices SET Entire Machine to ONE PriceView Data Four Different Ways HDC II Programming Guide View Machine DataView Total Paid Sales View Total Sales by Drink SizeSizes View Total Sales by Selection Both CUPView Total Sales by Individual Selection View Total Paid Sales by Price LineView Total Paid Vends Clear ALL Resettable DataView Total Paid Vends by Price Line View Amount in Coin BOX not Shown if Zero Clear Paid Sales Data onlyView Freevend Sales by Time Interval not Shown if Zero View Amount in Validator Not Shown if ZeroView Free Vends not Shown if Zero View Discount Sales by Time Interval Not Shown if ZeroView Winners Not Shown if Zero View Time Data 2301/30 00.2.4701/30TIMESET13.51View Total Unpaid Vends Not Shown if Zero View Total Unpaid Sales Not Shown if ZeroView Number of MUG Vends Not Shown if Zero View Number of Test Vends Not Shown if ZeroView Machine ID Number View CUP Ring Cycles Related to Surevend View Home Switch Usage Related toTest Vend Selections and Verify Credit Added HDC II Programming Guide Test the MachineTest Drop a CUP Test the Automatic Delivery DoorTest the Grinders Test the Machine HDC II Programming GuideTest the AIR Test the BrewerView Surevend Last Recorded Calibration Value Rinse the BrewerView Surevend Average Calibration Value Clear Tank Errors and Fill the TankTest the Display Information down before continuing View Diagnostic MessagesERR Download Data to a Pdcd SV.ERRSET Freevend Options FreeHDC II Programming Guide Test the Machine Programming Procedure Index Programming Procedure Index Programming Procedure Index Programming Procedure Index Programming Procedure Index Whipper, Test Terms and Conditions of Sale

675, 673, 677 specifications

Crane Merchandising Systems is a leading provider of advanced vending solutions, and their models 677, 673, and 675 stand out for their innovative features and technologies. These vending machines are designed to meet the evolving demands of consumer engagement and operational efficiency in retail settings.

The Crane 677 model is particularly noteworthy for its spacious design and flexible configuration options, allowing operators to customize merchandise selection according to consumer preferences. It comes equipped with an advanced touchscreen interface, which not only enhances user interaction but also enables advertisers to promote products through dynamic digital signage. The integration of cashless payment systems ensures that customers can make purchases conveniently using credit cards, mobile wallets, and other cashless methods, thus broadening the accessibility of the machine.

The 673 model emphasizes energy efficiency without compromising product availability. Its Energy Star rating reflects commitment to sustainability, making it an ideal choice for environmentally-conscious businesses. With a robust refrigeration system, it effectively manages temperature control, keeping perishable items fresh and appealing to customers. The 673 also features an intuitive inventory management system that enables operators to monitor stock levels in real-time, reducing both waste and operational downtime.

The Crane 675 model combines style with functionality, targeting high-traffic areas where aesthetics play a crucial role in attracting customers. Its sleek, modern design is complemented by customizable graphics, allowing operators to align the machine's appearance with branding strategies. Additionally, the 675 is outfitted with advanced telemetry technology, enabling remote monitoring of sales and inventory, helping operators optimize product selection based on real-time sales data.

All three models utilize Crane’s proprietary software that enhances operational capabilities, providing valuable analytics for machine performance, sales tracking, and consumer preferences. This data-driven approach helps operators refine their offerings and improve turnover, ensuring that the machines remain profitable and relevant.

In conclusion, Crane Merchandising Systems 677, 673, and 675 are at the forefront of vending technology, addressing contemporary challenges in consumer engagement and efficient management. Their features, such as touchscreens, energy-efficient designs, and advanced analytics, make them indispensable assets for any retail environment aiming to enhance customer experiences and operational effectiveness.
Top Page Image Contents