Crane Merchandising Systems 673, 677 View Surevend Average Calibration Value, Test the Display

Page 73

Test the Machine			HDC II Programming Guide
		VIEW SUREVEND™ AVERAGE CALIBRATION
		VALUE
1.	Press	, then press	until the display shows			.
	XXX represents the average sensor calibration value (should be between 50
	and 255 for proper sensor operation - i.e. 51 through 254). Although this
	number could go as low as 20, the SureVend™ system will be inoperative
	in this condition.
2.	CONTINUE.
		CLEAR TANK ERRORS AND FILL THE TANK
1.	Press	, then press	until the display shows			.
2.	Press	. This clears any tank error and starts filling the tank, if neces-
	sary. If it is taking a long time to fill the tank AND THERE ARE NO
	LEAKS, you may see		in the diagnostic list again. Just press
		again after making sure there are no other problems, such as a
				CAL.AVE	XXX
	restriction in the water inlet line or a clogged water filter.
3.	CONTINUE.
		TEST THE DISPLAY
1.	Press	, then press	until the display shows			. The
	"DRINK BEING SERVED" lamp is lighted (if so equipped), and remains
	lighted until you leave this function.			TANKFILL
				TANKFILL
2.	Press	to light all display segments; press		to turn them off.

3. Pressing a NUMBER KEY on the control panel causes all segments to dis-

play that character.	TANKERR		DSPLYTESTJuly, 2003
4. CONTINUE.
6730018		67

Image 73

Contents Page Crane Merchandising Systems Parts and Support Phone Numbers Table of Contents SureVend Configuration View Machine Data Test the Machine Getting around Introduction HDC II Programming GuideDisplays HDC II Programming Guide IntroductionFunction Keys Other KeysHelpful Hint Some ConventionsPress this button to Control Panel Switch Functions ExplainedSurevend Supervisor Mode Gain Access to the Supervisor Mode Basic Setup HDC II Programming GuideEnter a NEW Supervisor Code Enter a Freevend CodeEnter a NEW Data Recall Code HDC II Programming Guide Basic SetupUsage Lock or Unlock Mode or Payout Keys SET Printer or DEX Options Printer Mode onlySelect Printer Baud Rate SET DEX Options DEX Mode only SET Talker Mode HDC II Programming Guide Monetary SetupSelect Display Language Select Coin MechanismBill Selection Method Monetary Setup HDC II Programming GuideOFF Initial Setup of a NON-STANDARD Bill ValidatorSelect Monetary Options Select Card ReaderACC FFN Advanced Options SET UP Winner ModeSET UP MUG Discount Cup Configuration HDC II Programming GuideAN Example Press HDC II Programming Guide Cup ConfigurationDual Brew CONTINUE.LK.ABCDEFGH Disable Selections in the MerchandiserSET UP CUP Sizes 0X2 Assign CUP Sizes to Selections Supervisor Mode onlySET UP a HOT Drink Set up a Hot Drink HDC II Programming GuideDifferences HDC II Programming Guide Set up a Hot DrinkOptions Collecting Condiment Throws Collecting DRY Product Gram ThrowsEspresso = Chocolate times for cappuccino Collecting HOT Water Throws This water is HOT! Be carefulTable W1 Water Throw Default Times and Volumes Cappuccino RecipesEnter the Supervisor Code Caffé LatteSET the Machine to Vend a Large D Selection SET UP Your Selection European Cappuccino +WXYZBlended Selections BlendSET UP LOW Temperature Dispensing View or SET the HOT Water Tank TemperatureSET UP LOW Power Settings OfserviceOFF SET the Automatic Brewer Rinse TimeSET the Bowl Rinse Time RINTurn Surevend on or OFF HDC II Programming Guide SureVend ConfigurationOptional or Mandatory Surevend SET UP the Surevend ANTI-JACKPOT Timer SureVend Configuration HDC II Programming GuideView Software Version SET the Time of DAY HDC II Programming Guide Setup TimeSET MONTH, DATE, and Year SET Daylight Savings OptionSET TIME-OF-DAY Inhibit Vending Setup Time HDC II Programming GuideSET TIME-OF-DAY Free Vending SET TIME-OF-DAY Discount VendingInhibit Freevend Discount Time Interval EditingMWF Select a Standby Message Select AN OUT-OF-SERVICE MessageSelect a Freevend Message Shortcut Messages HDC II Programming GuideEND of Message Character Entering Your Message JhgiView Water Tank Temperature Check the Setup HDC II Programming GuideView Machine TYPE/CONFIGURATION Setting View CUP Sizes Assigned to Selections HDC II Programming Guide Check the SetupPayout Coins View Machine Data HDC II Programming Guide View Nonresettable Sales and Vend DataSET Prices SET Entire Machine to ONE PriceView Data Four Different Ways HDC II Programming Guide View Machine DataView Total Paid Sales View Total Sales by Drink SizeSizes View Total Sales by Selection Both CUPView Total Sales by Individual Selection View Total Paid Sales by Price LineView Total Paid Vends Clear ALL Resettable DataView Total Paid Vends by Price Line View Amount in Coin BOX not Shown if Zero Clear Paid Sales Data onlyView Freevend Sales by Time Interval not Shown if Zero View Amount in Validator Not Shown if ZeroView Free Vends not Shown if Zero View Discount Sales by Time Interval Not Shown if ZeroView Winners Not Shown if Zero View Time Data 2301/30 00.2.4701/30TIMESET13.51View Total Unpaid Vends Not Shown if Zero View Total Unpaid Sales Not Shown if ZeroView Number of MUG Vends Not Shown if Zero View Number of Test Vends Not Shown if ZeroView Machine ID Number View CUP Ring Cycles Related to Surevend View Home Switch Usage Related to Test Vend Selections and Verify Credit Added HDC II Programming Guide Test the Machine Test Drop a CUP Test the Automatic Delivery DoorTest the Grinders Test the Machine HDC II Programming GuideTest the AIR Test the BrewerView Surevend Last Recorded Calibration Value Rinse the BrewerView Surevend Average Calibration Value Clear Tank Errors and Fill the TankTest the Display Information down before continuing View Diagnostic MessagesERR Download Data to a Pdcd SV.ERRSET Freevend Options FreeHDC II Programming Guide Test the Machine Programming Procedure Index Programming Procedure Index Programming Procedure Index Programming Procedure Index Programming Procedure Index Whipper, Test Terms and Conditions of Sale