Vanguard Heating SBVBP(C) Chimneys, Relining Systems, High Altitude Installation, Owner’S Manual

Page 11
CHIMNEYS

OWNER’S MANUAL

VENTING INSTALLATION

Continued

CHIMNEYS

Complete familiarity with chimney con- dition, height, size, clearance to combus- tibles and other factors is essential.

NOTICE: Consult the authority having jurisdiction in your area regarding masonry chimney vent- ing applications.

NOTICE: A complete chimney inspection by a qualified person should be performed.

Appliances using B-vent connectors to vent into a masonry or factory-built chimney should not exceed 1 1/2 feet in length for every inch of connector diam- eter (3" vent connector has a maximum 4 1/2 foot length; 5" connector has maxi- mum 7 1/2 foot length).

Oversized chimneys should be relined with appropriate listed relining systems.

Cleanout access may be required.

RELINING SYSTEMS

Suitability and approval of relining ma- terials should be determined.

Condition, size, height, and termina- tion of the chimney to be relined must be determined.

No substitution of components should be made.

Joints and connectors should be made according to manufacturer’s instructions.

NOTICE: Consult the authority having jurisdiction in your area regarding listed chimney liner venting applications.

RELINING SYSTEMS WARNING: Operation of im- properly installed and maintained venting system could result in serious injury, property damage, or loss of life.

HIGH ALTITUDE

INSTALLATION

Your Vanguard B-vent burner system has been AGA tested and approved for eleva- tions from 0-2000 feet and CGA certified for elevations from 0-4500 feet.

When installing this burner system at an elevation above 2000 feet (in the USA), you may need to decrease the input rating by changing the existing burner orifice to a smaller size. Reduce input 4% for each 1000 feet above sea level. Check with your local gas company for proper orifice size identi- fication and proper orifice for your location.

When installing this stove and burner sys- tem at an elevation above 4500 feet (in Canada), check with local authorities.

For assistance with any high altitude instal- lation contact DESA International’s Tech- nical Service Department at 1-800-DESA- LOG (1-800-337-2564).

Figure 26 - Straight Installation into

Figure 27 - Typical Straight Installation

with Listed Chimney Liner

Masonry Chimney

 

106828

11

For more information, visit www.desatech.com

Image 11
Contents Do not try to light any appliance Do not touch any electrical switch OWNER’S OPERATION AND INSTALLATION MANUALFOR YOUR SAFETY FOR YOUR SAFETY WHAT TO DO IF YOU SMELL GASDANGER Carbon monoxide poisoning may lead to death SAFETY INFORMATIONSBVBNC AND SBVBPC CAST IRON STOVE AND BURNER SYSTEM WARNINGSLOCAL CODES PRODUCT FEATURESOWNER’S MANUAL PRODUCT IDENTIFICATIONetc. in the air exist, may discolor walls PRE-INSTALLATION PREPARATIONLOCATION AND SPACE REQUIREMENTS STOVE BODY ASSEMBLY CAST IRON STOVE AND B-VENT BURNER SYSTEM ASSEMBLYContinued INSTALLING OPTIONAL BLOWER ACCESSORY INSTALLING B-VENT BURNER SYSTEM INTO STOVE BODYINSTALLING REAR COVER CAST IRON STOVE AND DIRECT-VENT BURNER SYSTEM ASSEMBLYVENTING INSTALLATIONINSTALLATION PRECAUTIONS TYPE B-VENT INSTALLATION Listed B-0 or GreaterCHECKING VENT CAPACITY VENTING INSTALLATIONINSTALLATION OF LISTED B-1 VENT INSTALLING VENT SYSTEM IN A CHASERELINING SYSTEMS HIGH ALTITUDE INSTALLATIONCHIMNEYS FLUE GAS SPILLAGE TROUBLESHOOTING VENTING PROBLEMSCAST IRON STOVE AND B-VENT BURNER SYSTEM INSTALLATION INSTALLING GAS PIPING TO STOVE LOCATIONCAUTION Use only new, black iron or steel pipe. Inter Installation Items NeededCHECKING GAS CONNECTIONS CONNECTING STOVE/ BURNER SYSTEM TO GAS SUPPLYPressure Testing Gas Supply Piping System Pressure Testing Burner System Gas ConnectionsINSTALLING OPTIONAL WALL MOUNTED THERMOSTAT - GWMT1 INSTALLING OPTIONAL WALL MOUNT SWITCH GWMS2Installing Remote Receiver REMOVING/REPLACING GLASS DOOR Installing 9-Volt Battery in Hand- Held Remote Control UnitFigure 43 - Installing Log No Figure 46 - Installing Log No INSTALLING LOGS, LAVA ROCK, AND GLOWING EMBERSFigure 44 - Installing Log No Figure 45 - Installing Log NoLIGHTING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE LIGHTINGMANUAL LIGHTING PROCEDURE OPERATING STOVE WITH B-VENT BURNER SYSTEMGHRCTA Series Operation OPTIONAL REMOTEThermostat Control Operation GHRC Series OperationOPERATING OPTIONAL GWMT1 WALL MOUNTED THERMOSTAT OPERATING OPTIONAL BLOWER ACCESSORYPILOT ASSEMBLY INSPECTING BURNERSPILOT AND BURNERS CLEANING AND MAINTENANCEWARNING Turn off burner system and let cool before cleaning GLASS DOORREMEDY TROUBLESHOOTINGOBSERVED PROBLEM POSSIBLE CAUSEREMEDY If you cannot reach your gas supplier, call the fire department Clean pilot see Cleaning and MainteWARNING If you smell gas Shut off gas supply Do not try to light any applianceSERVICE HINTS REPLACEMENT PARTSTECHNICAL SERVICE WIRING DIAGRAMWALL MOUNTED ON/OFF SWITCH - GWMS2 Not Shown SPECIFICATIONSACCESSORIES RECEIVER AND HAND-HELD REMOTE CONTROL KIT GHRC23-4 ILLUSTRATED PARTS BREAKDOWNSBVBNC SBVBPC 23-3PARTS AVAILABLE - NOT SHOWN PARTS LISTPART NUMBER DESCRIPTIONIndicates Color Suffix Designation AMITY SCIVFC* SERIES PSCIVFC* SERIESPART INTERNATIONAL WARRANTY INFORMATIONLIMITED WARRANTY B-VENT BURNER SYSTEM AND AMITY STOVE CHASSIS KEEP THIS WARRANTY