Vanguard Heating SBVBP(C) Inspecting Burners, OPERATING OPTIONAL GWMT1 WALL MOUNTED THERMOSTAT

Page 21
OPERATING

OWNER’S MANUAL

OPERATING STOVE WITH B-VENT BURNER SYSTEM

Continued

OPERATING

OPTIONAL GWMT1

WALL MOUNTED

THERMOSTAT

INSPECTING WARNING: Do not connect the thermostat to a power source. Electrical shock and/or a fire haz- ard will occur.

Light the burner system as instructed in Lighting Instructions on page 19. Set wall thermostat to desired temperature.

This thermostat has been electronically calibrated at the factory and requires no adjustment or leveling.

OPERATING

OPTIONAL BLOWER

ACCESSORY

Blower controls are located on the left side of the rear cover when standing in front of stove with burner system in- stalled.

The DA3610TA thermostatically-con- trolled blower has an ON setting and an OFF setting. The blower will only run when the switch is in the ON position. In the OFF position, the blower will not operate.

If you are using DA3610TA blower with optional themostat (wall mount or re- mote control) for the burner system, your burner system and blower will not turn on and off at the same time. The burner system may run for several minutes be- fore the blower turns on. After the burner system modulates to the pilot position, the blower will continue to run. The blower will shut off after the burner sys- tem firebox temperature decreases.

The blower helps distribute heated air from the stove. Periodically check the top grates of the stove and remove any dust, dirt, or other obstructions that will hinder the flow of air.

Upon installation, the thermostat must be allowed to stabilize at room tempera- ture for a minimum of 30 minutes for proper operation.

To turn the burner system off, adjust thermostat to the lowest setting and turn the gas control knob back to PILOT. The pilot will remain lit.

IMPORTANT: To turn the pilot off, turn the control knob on the heater to the OFF position.

INSPECTING

BURNERS

Check pilot flame pattern and burner flame patterns often.

PILOT ASSEMBLY

The pilot assembly is factory preset for the proper flame height. Alterations may have occurred during shipping and handling. Call a qualified service person to readjust the pilot if necessary.

The height of the thermopile must be 3/8" to 1/2" above the pilot flame as shown in Figure

51.The flame from the pilot burner must extend beyond the thermopile.

If your pilot assembly does not meet these requirements:

•turn burner system off (see To Turn Off Gas to Appliance, page 19)

•seeTroubleshooting, pages 23 through 25

Thermopile

3/8" to 1/2"

Pilot Burner

Piezo Ignitor

Figure 51 - Pilot Assembly

BURNER FLAME PATTERN

Burner flames will be steady; not lifting or floating. Flame patterns will be different from unit to unit and will vary depending on installation type and weather conditions.

If the vent configuration is installed incor- rectly, the flames will lift or “ghost”. This can be dangerous. Inspect the flames after installation to ensure proper installation and performance.

Figure 52 shows a typical flame pattern. If burnerflamepatterndiffersfromthatdescribed:

•turn burner system off (see To Turn Off Gas to Appliance, page 19)

•seeTroubleshooting, pages 23 through 25

Figure 52 - Typical Flame Pattern

106828

21

For more information, visit www.desatech.com

Page 20 Page 22
Image 21
Page 20 Page 22
Contents FOR YOUR SAFETY OWNER’S OPERATION AND INSTALLATION MANUALFOR YOUR SAFETY WHAT TO DO IF YOU SMELL GAS Do not try to light any appliance Do not touch any electrical switchSBVBNC AND SBVBPC CAST IRON STOVE AND BURNER SYSTEM SAFETY INFORMATIONWARNINGS DANGER Carbon monoxide poisoning may lead to deathOWNER’S MANUAL PRODUCT FEATURESPRODUCT IDENTIFICATION LOCAL CODESPRE-INSTALLATION PREPARATION LOCATION AND SPACE REQUIREMENTSetc. in the air exist, may discolor walls STOVE BODY ASSEMBLY CAST IRON STOVE AND B-VENT BURNER SYSTEM ASSEMBLYContinued INSTALLING OPTIONAL BLOWER ACCESSORY INSTALLING B-VENT BURNER SYSTEM INTO STOVE BODYINSTALLING REAR COVER CAST IRON STOVE AND DIRECT-VENT BURNER SYSTEM ASSEMBLYINSTALLATION PRECAUTIONS INSTALLATIONTYPE B-VENT INSTALLATION Listed B-0 or Greater VENTINGINSTALLATION OF LISTED B-1 VENT VENTING INSTALLATIONINSTALLING VENT SYSTEM IN A CHASE CHECKING VENT CAPACITYHIGH ALTITUDE INSTALLATION CHIMNEYSRELINING SYSTEMS CAST IRON STOVE AND B-VENT BURNER SYSTEM INSTALLATION TROUBLESHOOTING VENTING PROBLEMSINSTALLING GAS PIPING TO STOVE LOCATION FLUE GAS SPILLAGECAUTION Use only new, black iron or steel pipe. Inter Installation Items NeededPressure Testing Gas Supply Piping System CONNECTING STOVE/ BURNER SYSTEM TO GAS SUPPLYPressure Testing Burner System Gas Connections CHECKING GAS CONNECTIONSINSTALLING OPTIONAL WALL MOUNTED THERMOSTAT - GWMT1 INSTALLING OPTIONAL WALL MOUNT SWITCH GWMS2Installing Remote Receiver REMOVING/REPLACING GLASS DOOR Installing 9-Volt Battery in Hand- Held Remote Control UnitFigure 44 - Installing Log No INSTALLING LOGS, LAVA ROCK, AND GLOWING EMBERSFigure 45 - Installing Log No Figure 43 - Installing Log No Figure 46 - Installing Log NoMANUAL LIGHTING PROCEDURE FOR YOUR SAFETY READ BEFORE LIGHTINGOPERATING STOVE WITH B-VENT BURNER SYSTEM LIGHTING INSTRUCTIONSThermostat Control Operation OPTIONAL REMOTEGHRC Series Operation GHRCTA Series OperationPILOT ASSEMBLY OPERATING OPTIONAL BLOWER ACCESSORYINSPECTING BURNERS OPERATING OPTIONAL GWMT1 WALL MOUNTED THERMOSTATWARNING Turn off burner system and let cool before cleaning CLEANING AND MAINTENANCEGLASS DOOR PILOT AND BURNERSOBSERVED PROBLEM TROUBLESHOOTINGPOSSIBLE CAUSE REMEDYREMEDY WARNING If you smell gas Shut off gas supply Clean pilot see Cleaning and MainteDo not try to light any appliance If you cannot reach your gas supplier, call the fire departmentTECHNICAL SERVICE REPLACEMENT PARTSWIRING DIAGRAM SERVICE HINTSACCESSORIES SPECIFICATIONSRECEIVER AND HAND-HELD REMOTE CONTROL KIT GHRC WALL MOUNTED ON/OFF SWITCH - GWMS2 Not ShownSBVBNC SBVBPC ILLUSTRATED PARTS BREAKDOWN23-3 23-4PART NUMBER PARTS LISTDESCRIPTION PARTS AVAILABLE - NOT SHOWNIndicates Color Suffix Designation AMITY SCIVFC* SERIES PSCIVFC* SERIESPART LIMITED WARRANTY B-VENT BURNER SYSTEM AND AMITY STOVE CHASSIS WARRANTY INFORMATIONKEEP THIS WARRANTY INTERNATIONAL
Top Page Image Contents