Craftsman 316.350850 warranty Limbing, Bucking Using a Sawhorse

Page 14

OPERATING INSTRUCTIONS

Fig. 15

LIMBING

Limbing a tree is the process of removing the branches from a fallen tree. Do not remove supporting limbs (A) until after the log is bucked (cut) into lengths (Fig. 16). Branches under tension should be cut from the bottom up to avoid binding the chain saw.

When bucking on a slope, always stand on the uphill side.

1.Log supported along entire length: Cut from top (over- buck), being careful to avoid cutting into the ground (Fig. 17).

2.Log supported on 1 end: First, cut from bottom (underbuck) 1/3 diameter of log to avoid splintering. Second, cut from above (overbuck) to meet first cut and avoid pinching (Fig. 18).

3.Log supported on both ends: First, overbuck 1/3 diame- ter of log to avoid splintering. Second, underbuck to meet first cut and avoid pinching (Fig. 19).

NOTE: The best way to hold a log while bucking is to use a sawhorse. When this is not possible, the log should be raised and supported by the limb stumps or by using supporting logs. Be sure the log being cut is securely supported.

A

Fig. 16

WARNING: Never cut tree limbs while standing on a

tree trunk.

BUCKING

Bucking is cutting a fallen log into lengths. Make sure you have a good footing and stand uphill of the log when cut- ting on sloping ground. If possible, the log should be sup- ported so that the end to be cut off is not resting on the ground. If the log is supported at both ends and you must cut in the middle, make a downward cut halfway through the log and then make the undercut. This will prevent the log from pinching the bar and chain. Be careful that the chain does not cut into the ground when bucking as this causes rapid dulling of the chain.

Fig. 18

Fig. 19

BUCKING USING A SAWHORSE

For personal safety and ease of cutting, the correct posi- tion for vertical bucking is essential (Fig. 20).

A.Hold the saw firmly with both hands and keep the saw to the right of your body while cutting.

B.Keep the left arm as straight as possible.

C.Keep weight on both feet.

CAUTION: While the saw is cut- ting, be sure the chain

and bar are being properly lubricated.

AB

C

Fig. 17

 

14

 

Fig. 20

 

 

 

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Operator’s Manual 55cc 2-CycleTable of Contents Warranty StatementOperate Your SAW Safely Symbol MeaningRules for Safe Operation Handle Fuel with Caution Kickback Safety PrecautionsMaintain Your SAW in Good Working Order Other Safety Precautions Fuel SafetySafety and International Symbols Symbol MeaningSafety Features Chain SAW ComponentsKickback Specifics Pinch KickbackOIL and Fuel Information Using Blended FuelsUsing Fuel Additives OIL and Fuel Mixing InstructionsFueling the Engine STARTING/STOPPING InstructionsGuide BAR and Chain OIL Chain BrakeStarting a Warm Engine Stopping InstructionsStarting a Cold Engine Automatic Oiler Chain Brake TestChain Lubrication Operating Instructions FellingBucking Bucking Using a SawhorseLimbing Maintenance and Repair Instructions Removing Guide BAR and Chain Replacing Guide BAR and ChainSAW Chain Tension Adjustment Chain Brake Mechanical TestFuel Filter Maintenance Requirements Check for Damaged or Worn PartsAIR Filter Check for Loose Fasteners and PartsSpark Arrester Screen Carburetor AdjustmentOIL Filter Spark PlugRemoving a Unit from Storage Guide BAR MaintenanceStoring a Chain SAW SAW Chain / BAR LubricationInertia Chain Brake Action Chain MaintenanceChain Replacement Information T I O N TroubleshootingU S E U SESpecifications EngineParts List Parts No DescriptionManufacturer’s Warranty Coverage Your Warranty Rights and ObligationsOwner’s Warranty Responsibilities Page Manual del usuario 55cc 2 TiemposAviso DE LA Proposición 65 DE CALI- Fornia ÍndiceDeclaración DE Garantía Nota Sobre EL Aspirador DE ChispasReglas DE Funcionamiento Seguro Advertencia Si no se obePrecaución Si no obedece Opere SU Sierra DE Forma SeguraPrecauciones DE Seguridad Ante REAC- Ciones Violentas Mantenga SU Sierra EN Buen Estado DE FuncionamientoManeje EL Combustible CON Cuidado Otras Precauciones DE Seguridad Seguridad DE CombustibleAdvertencia El con Advertencia Lea elAdvertencia Los Seguridad Y Símbolos InternacionalesComponentes DE LA Sierra Características DE SeguridadReacción de pellizcado Advertencia Kickback canEspecificaciones DE Reacción Advertencia Quite la tapa Precaución cionamientoAdvertencia La gasolina es Advertencia Añada comInstrucciones DE MARCHA/PARADA Instrucciones DE Parada Arrancar UN Motor FríoLubricado de la Cadena Arrancar UN Motor CalienteComprobación DE Freno DE Cadena Lubricador automáticoAdvertencia No corte un Advertencia una ruta deAdvertencia Nunca camine Instrucciones DE FuncionamientoTrocear Utilizando UN Caballete PelarTroceado Advertencia daños serios Instrucciones DE Mantenimiento Y ReparaciónQuitar LA Barra DE Guía Y LA Cadena Reemplazar LA Barra Y LA CadenaAjuste DE Tensión DE LA Sierra Mecánica Precaución Si la cadenaAdvertencia Freno de Comprobación Mecánica DEL Freno DE SierraCompruebe LAS Tuercas O Componentes Sueltos Filtro DE AireFiltro DE Combustible Pantalla DEL Aspirador DE Chispas Advertencia No abrase niFiltro DE Aceite BujíaMantenimiento DE LA Barra DE Guía Almacenar LA SierraRecuperar LA Unidad Tras EL ALMACE- Namiento Lubricado del engranajeAdvertencia más de C I Ó N Resolución DE ProblemasU S a Especificaciones MotorLista DE Componentes Componente DescripciónCobertura de la Garantía del Fabricante Sus derechos y obligaciones de garantíaResponsabilidades del propietario de la garantía Acuerdo de Protección de Reparaciones Arrglelo, en su casa o en la nuestra

316.350850 specifications

The Craftsman 316.350850 is a powerful and versatile tool that has gained popularity among DIY enthusiasts and professionals alike. Designed to cater to a variety of tasks, this product embodies a blend of efficiency, durability, and ease of use, making it a valuable addition to any tool collection.

One of the standout features of the Craftsman 316.350850 is its robust motor, which delivers impressive performance for cutting, shaping, and finishing materials. With a high RPM rating, it effectively handles a diverse range of tasks, whether it’s woodworking, metalworking, or general maintenance projects. The tool's motor is engineered for longevity, ensuring that it can withstand regular use without compromising performance.

The ergonomic design of the Craftsman 316.350850 is another highlight. The handle is crafted to provide comfortable grip and control, allowing users to operate the tool for extended periods without experiencing fatigue. Additionally, the tool’s lightweight construction enhances maneuverability, allowing for precise cuts and actions, even in tight spaces.

Equipped with advanced technology, the Craftsman 316.350850 incorporates safety features that prioritize user protection. These include a safety switch that prevents accidental start-ups, reducing the risk of injury. Moreover, the tool has built-in overheating protection, which monitors the motor temperature and automatically shuts off to prevent damage.

Another key characteristic is the tool's versatility. It comes with a variety of attachments and accessories that can be easily swapped out to accommodate different tasks. Whether you're sanding, grinding, or polishing, the Craftsman 316.350850 adapts quickly to meet the demands of the job at hand.

Maintenance of the Craftsman 316.350850 is hassle-free, thanks to its accessible design, which allows for easy cleaning and part replacement. The tool is also backed by a solid warranty, giving users confidence in their purchase and the assurance of support if issues arise.

In conclusion, the Craftsman 316.350850 stands out as a reliable, efficient, and user-friendly tool. Its powerful motor, ergonomic design, advanced safety features, and versatility make it a superb choice for anyone looking to tackle a range of projects with precision and ease. Whether for professional applications or home improvement tasks, this tool is designed to meet the challenges of modern craftsmanship.
Top Page Image Contents