Craftsman 316.350850 warranty Maintenance Requirements Check for Damaged or Worn Parts, AIR Filter

Page 18

MAINTENANCE AND REPAIR INSTRUCTIONS

MAINTENANCE REQUIREMENTS

CHECK FOR DAMAGED OR WORN PARTS

Check a Sears Service Center for replacement of dam- aged or worn parts.

NOTE: It is normal for a small amount of oil to appear under the saw after the engine stops. Do not confuse this with a leaking oil tank.

•STOP Switch - Ensure STOP switch functions properly by moving the switch up to the STOP position. Make sure the engine stops; then restart engine and continue.

•Fuel Tank - Do not use saw if fuel tank shows signs of damage or leaks.

•Oil Tank - Do not use saw if oil tank shows signs of damage or leaks.

CHECK FOR LOOSE FASTENERS AND PARTS

•Chain Brake Nuts

•Chain

•Muffler

•Cylinder Shield

•Air Filter cover

•Handle Screws

•Vibration Mounts

•Starter Housing

•Front Hand Guard

AIR FILTER

CAUTION: Never operate saw without the air filter.

Dust and dirt wil be drawn into engine and damage it. Keep the air filter clean.

1.Remove the top cover (A) by loosening the cover retaining screws. Cover will lift off (Fig. 31).

2.Clean air filter. Wash filter in clean, warm, soapy water. Rinse in clear, cool water. Air dry completely.

NOTE: It is advisable to have a supply of spare filters.

3.Install air filter. Install engine / air filter cover. Make sure cover fits properly. Tighten the cover retaining screws securely.

WARNING: To avoid serious per- sonal injury, always

turn your unit off and allow it to cool before you clean or service it.

B

A

Fig. 31

FUEL FILTER

CAUTION: Never operate saw without the fuel filter.

The fuel filter should be replaced after each 10 hours of use. Drain fuel tank before changing.

To empty fuel tank before removing fuel filter.

1.Pull fuel filter (A) out of tank with a bent wire (B) or long needle nosed pliers. Disconnect filter and discard (Fig. 32).

NOTE: Do not pull hose completely out of tank.

2.Install a new fuel filter on hose and push hose and fil- ter assembly back into tank so filter is positioned in front right corner.

3.Fill tank with fresh fuel/oil mixture. See Oil and Fuel Information. Install fuel cap.

A B

Fig. 32

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Operator’s Manual 55cc 2-CycleTable of Contents Warranty StatementSymbol Meaning Rules for Safe OperationOperate Your SAW Safely Kickback Safety Precautions Maintain Your SAW in Good Working OrderHandle Fuel with Caution Other Safety Precautions Fuel SafetySafety and International Symbols Symbol MeaningSafety Features Chain SAW ComponentsKickback Specifics Pinch KickbackOIL and Fuel Information Using Blended FuelsUsing Fuel Additives OIL and Fuel Mixing InstructionsFueling the Engine STARTING/STOPPING InstructionsGuide BAR and Chain OIL Chain BrakeStopping Instructions Starting a Cold EngineStarting a Warm Engine Chain Brake Test Chain LubricationAutomatic Oiler Operating Instructions FellingBucking Using a Sawhorse LimbingBucking Maintenance and Repair Instructions Removing Guide BAR and Chain Replacing Guide BAR and ChainSAW Chain Tension Adjustment Chain Brake Mechanical TestFuel Filter Maintenance Requirements Check for Damaged or Worn PartsAIR Filter Check for Loose Fasteners and PartsSpark Arrester Screen Carburetor AdjustmentOIL Filter Spark PlugRemoving a Unit from Storage Guide BAR MaintenanceStoring a Chain SAW SAW Chain / BAR LubricationChain Maintenance Chain Replacement InformationInertia Chain Brake Action T I O N TroubleshootingU S E U SESpecifications EngineParts List Parts No DescriptionYour Warranty Rights and Obligations Owner’s Warranty ResponsibilitiesManufacturer’s Warranty Coverage Page Manual del usuario 55cc 2 TiemposAviso DE LA Proposición 65 DE CALI- Fornia ÍndiceDeclaración DE Garantía Nota Sobre EL Aspirador DE ChispasReglas DE Funcionamiento Seguro Advertencia Si no se obePrecaución Si no obedece Opere SU Sierra DE Forma SeguraMantenga SU Sierra EN Buen Estado DE Funcionamiento Maneje EL Combustible CON CuidadoPrecauciones DE Seguridad Ante REAC- Ciones Violentas Otras Precauciones DE Seguridad Seguridad DE CombustibleAdvertencia El con Advertencia Lea elAdvertencia Los Seguridad Y Símbolos InternacionalesComponentes DE LA Sierra Características DE SeguridadAdvertencia Kickback can Especificaciones DE ReacciónReacción de pellizcado Advertencia Quite la tapa Precaución cionamientoAdvertencia La gasolina es Advertencia Añada comInstrucciones DE MARCHA/PARADA Instrucciones DE Parada Arrancar UN Motor FríoLubricado de la Cadena Arrancar UN Motor CalienteComprobación DE Freno DE Cadena Lubricador automáticoAdvertencia No corte un Advertencia una ruta deAdvertencia Nunca camine Instrucciones DE FuncionamientoPelar TroceadoTrocear Utilizando UN Caballete Advertencia daños serios Instrucciones DE Mantenimiento Y ReparaciónQuitar LA Barra DE Guía Y LA Cadena Reemplazar LA Barra Y LA CadenaAjuste DE Tensión DE LA Sierra Mecánica Precaución Si la cadenaAdvertencia Freno de Comprobación Mecánica DEL Freno DE SierraFiltro DE Aire Filtro DE CombustibleCompruebe LAS Tuercas O Componentes Sueltos Pantalla DEL Aspirador DE Chispas Advertencia No abrase niFiltro DE Aceite BujíaMantenimiento DE LA Barra DE Guía Almacenar LA SierraRecuperar LA Unidad Tras EL ALMACE- Namiento Lubricado del engranajeAdvertencia más de Resolución DE Problemas U S aC I Ó N Especificaciones MotorLista DE Componentes Componente DescripciónSus derechos y obligaciones de garantía Responsabilidades del propietario de la garantíaCobertura de la Garantía del Fabricante Acuerdo de Protección de Reparaciones Arrglelo, en su casa o en la nuestra

316.350850 specifications

The Craftsman 316.350850 is a powerful and versatile tool that has gained popularity among DIY enthusiasts and professionals alike. Designed to cater to a variety of tasks, this product embodies a blend of efficiency, durability, and ease of use, making it a valuable addition to any tool collection.

One of the standout features of the Craftsman 316.350850 is its robust motor, which delivers impressive performance for cutting, shaping, and finishing materials. With a high RPM rating, it effectively handles a diverse range of tasks, whether it’s woodworking, metalworking, or general maintenance projects. The tool's motor is engineered for longevity, ensuring that it can withstand regular use without compromising performance.

The ergonomic design of the Craftsman 316.350850 is another highlight. The handle is crafted to provide comfortable grip and control, allowing users to operate the tool for extended periods without experiencing fatigue. Additionally, the tool’s lightweight construction enhances maneuverability, allowing for precise cuts and actions, even in tight spaces.

Equipped with advanced technology, the Craftsman 316.350850 incorporates safety features that prioritize user protection. These include a safety switch that prevents accidental start-ups, reducing the risk of injury. Moreover, the tool has built-in overheating protection, which monitors the motor temperature and automatically shuts off to prevent damage.

Another key characteristic is the tool's versatility. It comes with a variety of attachments and accessories that can be easily swapped out to accommodate different tasks. Whether you're sanding, grinding, or polishing, the Craftsman 316.350850 adapts quickly to meet the demands of the job at hand.

Maintenance of the Craftsman 316.350850 is hassle-free, thanks to its accessible design, which allows for easy cleaning and part replacement. The tool is also backed by a solid warranty, giving users confidence in their purchase and the assurance of support if issues arise.

In conclusion, the Craftsman 316.350850 stands out as a reliable, efficient, and user-friendly tool. Its powerful motor, ergonomic design, advanced safety features, and versatility make it a superb choice for anyone looking to tackle a range of projects with precision and ease. Whether for professional applications or home improvement tasks, this tool is designed to meet the challenges of modern craftsmanship.
Top Page Image Contents