Craftsman 316.350850 warranty OIL Filter, Spark Arrester Screen, Spark Plug, Carburetor Adjustment

Page 19

MAINTENANCE AND REPAIR INSTRUCTIONS

OIL FILTER

NOTE: Drain oil reservoir before changing filter

1.Take the bottom plate off then use a wire with a hook

(A) and pull oil filter (B) from reservoir. Remove old filter and replace.

2.Put filter and oil line back into oil reservoir so filter is at bottom of reservoir.

B

A

Fig. 33

SPARK ARRESTER SCREEN

NOTE: A clogged spark arrester screen will dramatically reduce engine performance.

1.To flatten the corners of the lock plate to be able to access the retaining nuts. Remove 2 muffler retaining nuts (E), Lock plate (F) and muffler cover(G) (Fig. 34).

2.Remove spark arrester screen (H) from the metal baffle

(J). Replace screen with new one.

3.Reassemble the muffler components and tighten nuts securely.

J

H

G

F

E

SPARK PLUG

NOTE: For efficient operation of saw engine, spark plug must be kept clean and properly gapped.

1.Push STOP switch up.

2.Remove top Cover. Disconnect the wire connector from the spark plug by pulling and twisting at the same time (Fig. 35).

3.Remove spark plug with spark plug socket wrench.

DO NOT USE ANY OTHER TOOL.

WARNING: Do not sand blast, scrape or clean

electrodes. Grit in the engine could damage the cylinder.

4.Check electrode gaps with wire feeler gauge and set gaps to .025” (.635mm) if necessary.

5.Reinstall a new spark plug (champion RDJ8J or equiv- alent).

NOTE: A resistor spark plug must be used for replace- ment (part no. 9295-320001).

NOTE: This spark ignition system meets all requirements of the Canadian Interferen-Causing Equipment Regulations.

Fig. 35

CARBURETOR ADJUSTMENT

The carburetor was pre-set at the factory for optimum per- formance. If further adjustments are necessary, please take your unit to a Sears or other qualified service dealer.

Fig. 34

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents 55cc 2-Cycle Operator’s ManualWarranty Statement Table of ContentsRules for Safe Operation Symbol MeaningOperate Your SAW Safely Maintain Your SAW in Good Working Order Kickback Safety PrecautionsHandle Fuel with Caution Fuel Safety Other Safety PrecautionsSymbol Meaning Safety and International SymbolsChain SAW Components Safety FeaturesPinch Kickback Kickback SpecificsOIL and Fuel Mixing Instructions Using Blended FuelsUsing Fuel Additives OIL and Fuel InformationChain Brake STARTING/STOPPING InstructionsGuide BAR and Chain OIL Fueling the EngineStarting a Cold Engine Stopping InstructionsStarting a Warm Engine Chain Lubrication Chain Brake TestAutomatic Oiler Felling Operating InstructionsLimbing Bucking Using a SawhorseBucking Maintenance and Repair Instructions Replacing Guide BAR and Chain Removing Guide BAR and ChainChain Brake Mechanical Test SAW Chain Tension AdjustmentCheck for Loose Fasteners and Parts Maintenance Requirements Check for Damaged or Worn PartsAIR Filter Fuel FilterSpark Plug Carburetor AdjustmentOIL Filter Spark Arrester ScreenSAW Chain / BAR Lubrication Guide BAR MaintenanceStoring a Chain SAW Removing a Unit from StorageChain Replacement Information Chain MaintenanceInertia Chain Brake Action U SE TroubleshootingU S E T I O NEngine SpecificationsParts No Description Parts ListOwner’s Warranty Responsibilities Your Warranty Rights and ObligationsManufacturer’s Warranty Coverage Page 55cc 2 Tiempos Manual del usuarioNota Sobre EL Aspirador DE Chispas ÍndiceDeclaración DE Garantía Aviso DE LA Proposición 65 DE CALI- ForniaOpere SU Sierra DE Forma Segura Advertencia Si no se obePrecaución Si no obedece Reglas DE Funcionamiento SeguroManeje EL Combustible CON Cuidado Mantenga SU Sierra EN Buen Estado DE FuncionamientoPrecauciones DE Seguridad Ante REAC- Ciones Violentas Seguridad DE Combustible Otras Precauciones DE SeguridadSeguridad Y Símbolos Internacionales Advertencia Lea elAdvertencia Los Advertencia El conCaracterísticas DE Seguridad Componentes DE LA SierraEspecificaciones DE Reacción Advertencia Kickback canReacción de pellizcado Advertencia Añada com Precaución cionamientoAdvertencia La gasolina es Advertencia Quite la tapaInstrucciones DE MARCHA/PARADA Arrancar UN Motor Frío Instrucciones DE ParadaLubricador automático Arrancar UN Motor CalienteComprobación DE Freno DE Cadena Lubricado de la CadenaInstrucciones DE Funcionamiento Advertencia una ruta deAdvertencia Nunca camine Advertencia No corte unTroceado PelarTrocear Utilizando UN Caballete Instrucciones DE Mantenimiento Y Reparación Advertencia daños seriosReemplazar LA Barra Y LA Cadena Quitar LA Barra DE Guía Y LA CadenaComprobación Mecánica DEL Freno DE Sierra Precaución Si la cadenaAdvertencia Freno de Ajuste DE Tensión DE LA Sierra MecánicaFiltro DE Combustible Filtro DE AireCompruebe LAS Tuercas O Componentes Sueltos Bujía Advertencia No abrase niFiltro DE Aceite Pantalla DEL Aspirador DE ChispasLubricado del engranaje Almacenar LA SierraRecuperar LA Unidad Tras EL ALMACE- Namiento Mantenimiento DE LA Barra DE GuíaAdvertencia más de U S a Resolución DE ProblemasC I Ó N Motor EspecificacionesComponente Descripción Lista DE ComponentesResponsabilidades del propietario de la garantía Sus derechos y obligaciones de garantíaCobertura de la Garantía del Fabricante Acuerdo de Protección de Reparaciones Arrglelo, en su casa o en la nuestra

316.350850 specifications

The Craftsman 316.350850 is a powerful and versatile tool that has gained popularity among DIY enthusiasts and professionals alike. Designed to cater to a variety of tasks, this product embodies a blend of efficiency, durability, and ease of use, making it a valuable addition to any tool collection.

One of the standout features of the Craftsman 316.350850 is its robust motor, which delivers impressive performance for cutting, shaping, and finishing materials. With a high RPM rating, it effectively handles a diverse range of tasks, whether it’s woodworking, metalworking, or general maintenance projects. The tool's motor is engineered for longevity, ensuring that it can withstand regular use without compromising performance.

The ergonomic design of the Craftsman 316.350850 is another highlight. The handle is crafted to provide comfortable grip and control, allowing users to operate the tool for extended periods without experiencing fatigue. Additionally, the tool’s lightweight construction enhances maneuverability, allowing for precise cuts and actions, even in tight spaces.

Equipped with advanced technology, the Craftsman 316.350850 incorporates safety features that prioritize user protection. These include a safety switch that prevents accidental start-ups, reducing the risk of injury. Moreover, the tool has built-in overheating protection, which monitors the motor temperature and automatically shuts off to prevent damage.

Another key characteristic is the tool's versatility. It comes with a variety of attachments and accessories that can be easily swapped out to accommodate different tasks. Whether you're sanding, grinding, or polishing, the Craftsman 316.350850 adapts quickly to meet the demands of the job at hand.

Maintenance of the Craftsman 316.350850 is hassle-free, thanks to its accessible design, which allows for easy cleaning and part replacement. The tool is also backed by a solid warranty, giving users confidence in their purchase and the assurance of support if issues arise.

In conclusion, the Craftsman 316.350850 stands out as a reliable, efficient, and user-friendly tool. Its powerful motor, ergonomic design, advanced safety features, and versatility make it a superb choice for anyone looking to tackle a range of projects with precision and ease. Whether for professional applications or home improvement tasks, this tool is designed to meet the challenges of modern craftsmanship.
Top Page Image Contents