Craftsman ZTS 6000, 107.289860 manual Clean Deck CHECK/REPLACE Mower Blades

Page 24

CLEAN DECK &

 

 

CHECK/REPLACE

MOWER BLADES

 

Service Interval: 25 hours or as required.

 

WARNING

 

For your personal safety, do not handle the sharp

 

mower blades with bare hands. Careless or

 

improper handling of blades may result in serious

 

injury.

 

 

WARNING

LOOSEN

 

 

For your personal safety, blade mounting

Figure 23. Blade Removal

capscrews must each be installed with two spring

 

washers or a hex washer and spring washer, then

 

securely tightened. Torque blade mounting nut to

 

80-90 ft-lbs(108-122

Nm).

 

1.Remove mower deck (see "Mower Deck Removal" in the OPERATION section).

2.Remove blade to inspect it or to safely access the underside of the mower deck (see Figure 23). Use a block of wood to prevent blade rotation while loosen- ing the capscrew by turning it counterclockwise.

3.Remove the nut (C, Figure 24), spring washers (B), and blade.

. Clean the underside of the mower deck.

5.Inspect the blades for nicks or dull edges. Use a file to sharpen blade to a fine edge. If the blade is dam- aged, it must be replaced.

. Balance the blade as shown in Figure 25. Center the blade'shole on a nail lubricated with a drop of oil. A balanced blade will remain level. If the blade is not balanced, continue to sharpen the heavy side until it balances.

. Reinstall the blade with the lift wings (D, Figure 24) pointing up toward the mower deck as shown.

. Reinstall the spring washers (B, Figure 24) and nut

(C). Use a wooden block (A) to prevent blade rotation while tightening the nut (C) to 80-90 ft-lbs (108-122 Nm).

Figure

24. Blade Installation

 

A.

4x4

Wood Block

C. Blade Nut

B.

Spring Washers

D. Lift Wings

Workbench

Nail

Figure 25. Balancing The Blade

24

Image 24
Contents ZTS For answers to your questions about this Product, callPage Warranty Statement Storage Safety Rules Information AssemblyIdentification Numbers Pre-Operation RepairGeneral Operation Transporting and StorageTowed Equipment RIDE-ON Units ChildrenEmissions Ignition SystemSuggested Guide for Sighting Slopes for Safe Operation Only RiDE UP and Down HillService and Maintenance Service & MaintenanceSafe Handling of Gasoline Safety & Operation Decals SwitchEnglish and Spanish Installing the Seat 16-18 x 3/4Installing the Seat Safety Switch Installing the Seat Safety SwitchSetting UP the Ground Speed Control Levers Setting Up the Ground Speed Control LeversRemove the Packaging Materials Check the Tire PressureCheck Engine Oil Level Fill=Up with Fresh GasolineControl Functions GroundSpeed Levers Parking Brake LeverGeneral Operating Safety Checks Before Starting Fuel RecommendationsEmergency Stopping Stopping the Rider & EngineStarting the Engine MowingSmooth Travel Forward Travel PracticeReverse Travel Practice Forward Travel Reverse TravelPractice Turning Around a Corner Practice Turning In Place Executing TurnsExecuting an End-Of-Row Zero Turn Turning In PlaceMower Deck Removal Installation Installing the Mower DeckRemoving the Mower Deck Maintenance Schedule Rider MaintenanceMaintenance All ModelsAccessing the Engine Compartment Clean Debris from Rider and Engine CompartmentClean Debris from Engine Cooling Areas and AIR Filter Check Tire PressureLubrication GreaseClean Deck CHECK/REPLACE Mower Blades For your personal safety, blade mountingCapscrews must each be installed with two spring Cleaning the Battery and Cables Check Rider Safety SystemOperational Safety Checks Adjust PTO Clutch Adjustment Nut Feeler GaugeCheck Engine OIL Level Change Engine OILChange Engine OIL & Filter AIR Filter & PRE-CLEANER Air Filter Removal & InstallationReplace Spark Plug Ground Speed Control Lever Adjustment Speed Balancing AdjustmentCutting Height Adjustment PTO Clutch AdjustmentBrake Adjustment Battery ChargingEngine Adjustments For all moving parts to stop. Remove the keyMower Deck Leveling Adjustments Side to Side LevelingTrunnion Jam Nuts Mower Belt Replacement Front To Back LevelingBefore Storage After StorageTroubleshooting the Rider WillTroubleshooting MowerZTS Page Declaracibn De Garantia Reglas e Informacibn de SeguridadNdmeros de Identificacibn Partes de Refaccibn Operacibn Repare El Acuerdo De la MantenimientoOperacion General Transporte Y AlmacenamientoOperacion EN Cuestas Equipo Remolcado Unidades MontaEmisiones Sistema DE EncendidoDoblar a LO LARGo DE LA Servicio Y Mantenimiento Manejo Seguro de la GasolinaCALCOMANiAS DE Seguridad Y OPERAClON Recolector de Hierba con Bolsa Gemela Faro delantero LlavesInstrucciones de Disposicion lngles/EspaSol Manual del Operador y Libro de Partes lngles/EspaSolInstalacion DEL Asiento Figura 1. Instalaci6n del asientoInstalacion DEL Interrupter DE Seguridad DEL Asiento 16-18 16-18 x 1-3/4 Retirar los Materiales de Empaque Revisar la Presi6n de las MantasRevisar el Nivel de Aceite del Motor Cargar la BateriaControl de Aceleracibn Estrangulador Choke-O-Matic PalancadeControlPalancas deVelocidad PalancasdeVelocidad GasolinaAjuste de Altura de Corte de la Interruptor de EncendidoNterruptor de Cuchillas de la Palancas de Desembrague deADVERTENCIA- Remolques Verificaciones Antes DE ArrancarParo DE Emergencia Detener EL Montable Y EL MotorArrancar EL Motor Podar EL C¢SPEDPractica DE Manejo Traslado sin prob- lemasManejo Hacia AdelantePractica de dar Vuelta en una Esquina Ejecutar VueltasEjecutar un Giro Cero al Final de la Fila Practica de Vuelta en el LugarRemocion E Instalacion DE LA Cubierta DE LA Sesgadora Retirar la Cubierta de la SesgadoraInstalar la Cubierta de la Sesgadora Programa DE Mantenimiento Maintenimiento DEL MotorAntes de Primavera Cada AnualGanar Acceso AL Compar Timiento DEL Motor Limpiar Despojos DEL Tractor Y DEL Compartimiento DEL MotorFiltro DE Aire Verificar Presion DE LAS LLAN- TASLubricacion Lubricacibn del montableFigura 23. Remoci6n del Aspa Figura 25. Equilibrar el AspaLimpiar Baterja Y Cables Los ojosVERIFICAR/AJUSTAR Embrague DEL PTO Verifique EL Nivel DE Aceite DEL Motor Verifique EL Nivel DE Aceite DEL Motor Y EL FiltroServicio DEL Filtro DE Airey DEL PRE Purificador Remocibn e instalacibn del filtro de aireReemplace LA Bujja DE Entrehierro de la BujiaAjuste DE Palanca DE Control DE Velocidad Ajuste DE Embrague DEL PTOPara Ajustar la Altura de las Palancas de Control Ajuste DE LOS Frenos Recarga DE LA BaterjaAjustes DEL Motor Ajuste DE Nivel DE LA Cubierta DE LA Podadora Nivelado de un Lado a OtroNivelado de Adelante hacia Atras Figura 40. Orientar las Aspas de Adelante hacia AtrsMotor AlmacenamientoDiagn6stico Del TractorDiagn6stico La sesgadora Gadora es deImpulsa RepairParts Frame, Body & Seat Group ZTS 6000Frame Body Seat Group FootnotesFrame, Body & Seat Group Lockwasher Engine Group 21HP Briggs & Stratton ZTS 6000 Engine Group 21HP Briggs & Stratton REF no Part QTYTransmission Group Transmission Group Transmission Group Transmission Group ZTS 6000 36 \ Controls GroupControls Group36 \ REF no Part NO. QTY. Description Electrical Group ZTS 6000 Lift Group Trunnion Tl/k Wheel & Tire GroupWheel Tire Group Decals Group Decal Mower Deck Clutch & Support Group ZTS 6000 Mower Deck Clutch Support Group Mower Deck Housing & Arbor Group ZTS 6000 CoverCylinder Assembly 331877-0144-B1 Assemblies include all parts shown in framesZTS8000107 331 87701 44-B1 75o Zrs8000lo7- .28986o 331877-0144-B1zrsooolo7- .28988o Zrsooolo7- .28986o331877.-0144-B1 331877.-0144-B1 693551 Motor-Starter 802 691286 Cap-End 331 877-01 44-B1 Needle Eter PTS-40 PTS PTS Sears Installation Service Repair Protection AgreementsAcuerdo de Proteccion de Reparaciones Servicio de Instalacion de SearsYour Home Call anytime, day or night U.S.A. and Canada