Woods Equipment S105-3, S106-3 manual General Mowing, Blade Selection, Cutter Head Hydraulic Lift

Page 15

Do not disconnect hydraulic lines until machine is securely blocked or placed in lowest position and system pressure is released by operating valve levers.

GENERAL MOWING

Look down and to the rear and make sure area is clear before operating in reverse.

This cutter may be used for mowing in either forward or reverse. Reverse mowing will enable you to cut close to obstructions. When mowing in both directions, cutter should be level front to rear.

Blade Selection

CAUTION

Your dealer can supply genuine replacement blades. Substitute blades may not meet original equipment specifications and may be dangerous.

General purpose suction blades are recommended for normal mowing. Flat blades are recommended for brush mowing and in sandy areas where abrasive action could cause excessive blade wear. Final blade selection must be left to your judgement, depending on the job to be accomplished and the desired results.

Cutter Head Hydraulic Lift

The cutter head is raised with a 3-1/2" single-acting hydraulic cylinder. The cylinder, which lifts only, may be controlled by either tractor hydraulic controls or an optional auxiliary hydraulic valve. The head is lowered by gravity.

There is an orifice restrictor in the hydraulic line to con- trol the fall.

NOTICE

Always raise center section before raising or lowering cutter head. This will provide clearance for the inside gauge wheel. Failure to raise center section will result in rolling tire off of rim.

Never install a double-acting cylinder as dam- age to the cutter will occur.

When mowing, set hydraulic valve in the float position. This will allow cutter to follow the ground contour.

Always use the tractor hydraulic system with built-in float when available. On tractors with closed-center systems that do not have float, you may lock the con- trol in the down mode. This will allow the head to float.

Do not lock the control in the down mode on tractors with open-center systems. Refer to the tractor owner's manual or contact your dealer if you have questions as to the type of hydraulic system used on your tractor.

Operate the open-center system that does not have a float with the control in the neutral position. This will allow cutter head to float up when encountering an obstruction.

For tractors without hydraulic controls, an auxiliary con- trol valve may be used. It has three positions: pull out to raise, push in to slightly lower, and push all the way in and snap into detent to allow cutter head to float.

Tractor and Cutter Operation

Full chain shielding must be installed when operating in populated areas or other areas where thrown objects could injure people or damage property.

If this machine is not equipped with full chain shielding, operation must be stopped when any- one comes within 300 feet (92 m).

This shielding is designed to reduce the risk of thrown objects. The mower deck and protec- tive devices cannot prevent all objects from escaping the blade enclosure in every mowing condition. It is possible for objects to ricochet and escape, traveling as much as 300 feet (92 m).

Keep bystanders away from equipment.

Never allow riders on power unit or attachment.

This cutter is operated with tractor controls. Engage the PTO control at idle rpm to prevent undue stress on tractor, cutter drivelines and gearboxes. Set tractor PTO speed and tractor throttle to operate at either 540 rpm or 1000 rpm, depending on which model cutter you have. Change ground travel by using higher or lower gears. Be sure operator is familiar with all tractor con- trols and can stop it and the cutter in an emergency. The operator should give complete, undivided attention to operating the tractor and cutter when mowing.

29977 (Rev. 1/23/2009)

Operation 15

 

 

Image 15
Contents Ditch Bank Rotary Cutter To the Dealer IntroductionTable of Contents General Information SpecificationsSafety Free Mower Safety VideoTraining Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishPreparation Safety RulesInstallation TrainingOperation TransportationStorage MaintenanceReplace Immediately If Damaged Safety & Instructional DecalsSafety Decals from previous Be Careful Tractor Front END Stability OperationOperation General Tractor RequirementsAttaching Cutter to Tractor Cutting Height Attitude AdjustmentSide Skid Adjustment Optional Tailwheel AdjustmentTractor and Cutter Operation General MowingBlade Selection Cutter Head Hydraulic LiftTransport Brush and Ditch Bank MowingOwner Service Owner ServiceLubrication Blade Removal Blade InstallationSlip Clutch Adjustment Blade ServicingPeriodically or Before Extended Storage CleaningChain Shielding Repair After Each UseTrouble Shooting Trouble ShootingSeal Installation Dealer ServiceDealer Service Gearbox MaintenanceCrossbar Shimming InstallationDealer Service Universal Joint Repair Joint DisassemblyJoint Assembly Operation SPRING-LOADED Wheel Yoke AdjustmentSPOOL, 3-WAY Valve Open-Center or Closed-CenterDelivery Check Dealer Check ListDealer Check Lists PRE-DELIVERY Check ListDP1 AssemblyAssembly Drive Shaft InstallationAttaching Cutter Head to Center Frame Lift Cylinder InstallationLift Link Installation Mounting A-Frame on Center FrameSide Drive Installation Figure Side Shield InstallationCutter Head Gearbox Shield Installation Counterweight Installation Optional Tire and Skid Assembly InstallationChain Shielding Installation Check Chain InstallationControl Valve Installation Optional Tailwheel OptionalStump Jumper Optional Assembly Parts Parts IndexCenter Section Assembly Hardware Cutter Head Section Assembly Early S106-3 Tubular Side Drive Assembly Cutter Head Gearbox Assembly Input Gearbox Assembly Standard Drive Front Half of 2-JOINT Drive 35RSlip Clutch Assembly Joint Shielding Plastic Used on Later Machines Integral U-JOINT Shielding Used on Earlier MachinesPart QTY Description 2 Bore & 8 Stroke Hydraulic CylinderPiston SPOOL, 3-WAY Valve Optional Pneumatic Tailwheel Assembly HUB Assembly for Pneumatic Tailwheel Pneumatic Tire Assembly for TailwheelTailwheel Assembly Tailwheel & Gauge Wheel Assembly Gauge Wheel & Tailwheel HUB & Axle AssemblyStandard 1 Shaft Heavy-Duty 1-1/4 Shaft Stump Jumper Optional Crossbar Puller AssemblyMetric Series Bolt Torque ChartSAE Series Torque Chart AppendixAbbreviations Bolt Size ChartIndex IndexWarranty South Illinois Route Post Office Box Oregon, Illinois