Woods Equipment S106-3, S105Q-3 Dealer Check Lists, PRE-DELIVERY Check List, Delivery Check

Page 28

DEALER CHECK LISTS

PRE-DELIVERY CHECK LIST

(DEALER’S RESPONSIBILITY)

Inspect the equipment thoroughly after assembly to ensure it is set up properly before delivering it to the customer.

The following check lists are a reminder of points to inspect. Check off each item as it is found satisfactory or after proper adjustment is made.

___ Check that all safety decals are installed and in good condition. Replace if damaged.

___ Check that shields and guards are properly installed and in good condition. Replace if dam-

 

aged.

___

Properly attach implement to tractor and make all

 

necessary adjustments.

___

Check all bolts to be sure they are tight.

___

Check and grease all lubrication points as identi-

 

fied in “Service”.

___

Check that blades have been properly installed.

DELIVERY CHECK

(DEALER’S RESPONSIBILITY)

___ Instruct customer how to lubricate and explain importance of lubrication.

___ Point out the safety decals. Explain their meaning and the need to keep them in place and in good condition. Emphasize the increased safety haz- ards when instructions are not followed.

___ Present Operator's Manual and request that cus- tomer and all operators read it before operating equipment. Point out the manual safety rules, explain their meanings and emphasize the increased safety hazards that exist when safety rules are not followed.

___ Show customer the safe, proper procedures to be used when mounting, dismounting, and storing equipment.

___ Point out all guards and shields. Explain their importance and the safety hazards that exist when not kept in place and in good condition.

28 Dealer Check List

29977 (Rev. 1/23/2008)

 

 

Image 28
Contents Ditch Bank Rotary Cutter Introduction To the DealerTable of Contents Specifications General InformationFree Mower Safety Video SafetyTraining Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishSafety Rules InstallationTraining PreparationTransportation OperationMaintenance StorageSafety & Instructional Decals Replace Immediately If DamagedSafety Decals from previous Be Careful Operation OperationGeneral Tractor Requirements Tractor Front END StabilityCutting Height Attitude Adjustment Side Skid AdjustmentOptional Tailwheel Adjustment Attaching Cutter to TractorGeneral Mowing Blade SelectionCutter Head Hydraulic Lift Tractor and Cutter OperationBrush and Ditch Bank Mowing TransportOwner Service Owner ServiceLubrication Blade Installation Slip Clutch AdjustmentBlade Servicing Blade RemovalCleaning Chain Shielding RepairAfter Each Use Periodically or Before Extended StorageTrouble Shooting Trouble ShootingDealer Service Dealer ServiceGearbox Maintenance Seal InstallationCrossbar Installation ShimmingDealer Service Joint Disassembly Universal Joint RepairJoint Assembly SPRING-LOADED Wheel Yoke Adjustment SPOOL, 3-WAY ValveOpen-Center or Closed-Center OperationDealer Check List Dealer Check ListsPRE-DELIVERY Check List Delivery CheckAssembly AssemblyDrive Shaft Installation DP1Lift Cylinder Installation Lift Link InstallationMounting A-Frame on Center Frame Attaching Cutter Head to Center FrameSide Shield Installation Side Drive Installation FigureCutter Head Gearbox Shield Installation Tire and Skid Assembly Installation Chain Shielding InstallationCheck Chain Installation Counterweight Installation OptionalTailwheel Optional Control Valve Installation OptionalStump Jumper Optional Assembly Parts Index PartsCenter Section Assembly Hardware Cutter Head Section Assembly Early S106-3 Tubular Side Drive Assembly Cutter Head Gearbox Assembly Input Gearbox Assembly Front Half of 2-JOINT Drive 35R Standard DriveSlip Clutch Assembly Integral U-JOINT Shielding Used on Earlier Machines Joint Shielding Plastic Used on Later Machines2 Bore & 8 Stroke Hydraulic Cylinder Part QTY DescriptionPiston SPOOL, 3-WAY Valve Optional Pneumatic Tailwheel Assembly Pneumatic Tire Assembly for Tailwheel HUB Assembly for Pneumatic TailwheelTailwheel Assembly Gauge Wheel & Tailwheel HUB & Axle Assembly Tailwheel & Gauge Wheel AssemblyStandard 1 Shaft Heavy-Duty 1-1/4 Shaft Crossbar Puller Assembly Stump Jumper OptionalBolt Torque Chart SAE Series Torque ChartAppendix Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty South Illinois Route Post Office Box Oregon, Illinois