Woods Equipment S105-3, S106-3, S105Q-3 Side Drive Installation Figure, Side Shield Installation

Page 31

Side Drive Installation (Figure 23)

1.Side drive mounting point

2.Drive joint support arm

3.Inner side drive assembly

4.Side drive mounting point

5.Outer side drive assembly

6.Drive joint support arm

10.5/8 x 2-1/4" Bolt

11.1/2" Flanged hex lock nut

12.1/2 x 5" Bolt

13.5/8 x 3-1/2" Bolt

14.Inner shear sleeve

15.Snap ring

16.1/8 x 1" Cotter pin

17.7/16 x 3" Hard shear pin

18.5/8" Hex nut

19.5/8" Hex jam nut

20.Cup washer

21.5/8 x 1 x 7/16" Sleeve

Figure 23. Side Drive Installation

Assemble inner drive assembly (3) into outer drive assembly (5). Check to ensure drive shaft and U-joints are indexed properly. The small pin on end of square shaft should mate with outer drive for proper installa- tion. Place offset plates of side drive assembly over bearing block of inner drive assembly, and attach with bolts (12) and lock nuts (11). Do not tighten hardware at this time.

Install inner shear sleeve (14) into end of U-joint sleeve and work snap ring (15) into groove to retain shear sleeve (14).

Install inner drive (3) into gearbox on center section. With keys in place in cutter head gearbox shaft, slide outer drive onto shaft, align hole in inner shear sleeve, gear shaft and U-joint sleeve and install hard shear pin (17). Retain with cotter pin (16).

Attach drive joint support arms (23 & 6) to side drive mounting points (1 & 4). Insert bolt (10) through hole in mounting point (1), place sleeve (21) over bolt, and install cup washers (20) with cups toward sleeve. Install this assembly through support arm (2), apply Loctite) to bolt, then install jam nut (19) and tighten. Secure with nut (18).

Repeat this procedure for support arm (6), using bolt (13).

Insert grease zerk into threaded hole on end cap of drive shaft shield. For location, see page 36, item 99. Tighten as required.

Side Shield Installation

Refer to parts drawing on page 36.

Install inner drive shield (49) over outside of plates on outer drive (1). Tighten all hardware. Attach cylinder and drive shield (26) with four self-tapping screws.

Install drive shaft shield (5) over end of drive shaft that protrudes through the center section gearbox with self- tapping screws.

Cutter Head Gearbox Shield Installation

Refer to page 38.

Remove four gearbox cover bolts. Place shield (34) over gearbox and reinstall bolts.

Blade Installation

Raise cutter.

The cutter blades are shipped separately.

Remove bolt, spacer plug, keyhole plate and spacer plates. Drop the blade pin out. Discard shipping spacer.

Install pin upward through blade. Be sure blade is right side up. Reinstall pin. Replace spacers and keyhole plate. If the fit is too tight, one of the thin spacers may be removed. Reinstall spacer plug and bolt. It is not necessary to torque the bolt excessively.

29977 (Rev. 1/23/2009)

Assembly 31

 

 

Image 31
Contents Ditch Bank Rotary Cutter To the Dealer IntroductionTable of Contents General Information SpecificationsSafety Free Mower Safety VideoTraining Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishPreparation Safety RulesInstallation TrainingOperation TransportationStorage MaintenanceReplace Immediately If Damaged Safety & Instructional DecalsSafety Decals from previous Be Careful Tractor Front END Stability OperationOperation General Tractor RequirementsAttaching Cutter to Tractor Cutting Height Attitude AdjustmentSide Skid Adjustment Optional Tailwheel AdjustmentTractor and Cutter Operation General MowingBlade Selection Cutter Head Hydraulic LiftTransport Brush and Ditch Bank MowingOwner Service Owner ServiceLubrication Blade Removal Blade InstallationSlip Clutch Adjustment Blade ServicingPeriodically or Before Extended Storage CleaningChain Shielding Repair After Each UseTrouble Shooting Trouble ShootingSeal Installation Dealer ServiceDealer Service Gearbox MaintenanceCrossbar Shimming InstallationDealer Service Universal Joint Repair Joint DisassemblyJoint Assembly Operation SPRING-LOADED Wheel Yoke AdjustmentSPOOL, 3-WAY Valve Open-Center or Closed-CenterDelivery Check Dealer Check ListDealer Check Lists PRE-DELIVERY Check ListDP1 AssemblyAssembly Drive Shaft InstallationAttaching Cutter Head to Center Frame Lift Cylinder InstallationLift Link Installation Mounting A-Frame on Center FrameSide Shield Installation Side Drive Installation FigureCutter Head Gearbox Shield Installation Counterweight Installation Optional Tire and Skid Assembly InstallationChain Shielding Installation Check Chain InstallationTailwheel Optional Control Valve Installation OptionalStump Jumper Optional Assembly Parts Parts IndexCenter Section Assembly Hardware Cutter Head Section Assembly Early S106-3 Tubular Side Drive Assembly Cutter Head Gearbox Assembly Input Gearbox Assembly Standard Drive Front Half of 2-JOINT Drive 35RSlip Clutch Assembly Joint Shielding Plastic Used on Later Machines Integral U-JOINT Shielding Used on Earlier MachinesPart QTY Description 2 Bore & 8 Stroke Hydraulic CylinderPiston SPOOL, 3-WAY Valve Optional Pneumatic Tailwheel Assembly HUB Assembly for Pneumatic Tailwheel Pneumatic Tire Assembly for TailwheelTailwheel Assembly Gauge Wheel & Tailwheel HUB & Axle Assembly Tailwheel & Gauge Wheel AssemblyStandard 1 Shaft Heavy-Duty 1-1/4 Shaft Stump Jumper Optional Crossbar Puller AssemblyMetric Series Bolt Torque ChartSAE Series Torque Chart AppendixAbbreviations Bolt Size ChartIndex IndexWarranty South Illinois Route Post Office Box Oregon, Illinois