Woods Equipment TS1680Q manual 1000 RPM

Page 12

15922-C

18865--C

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

(Safety Decals continued from previous page)

5 - PN 18864

DANGER

ROTATING DRIVELINE

CONTACT CAN CAUSE DEATH

KEEP AWAY!

DO NOT OPERATE WITHOUT -

All driveline guards, tractor and equipment shields in place

Drivelines securely attached at both ends

Driveline guards that turn freely on
driveline	18864-C
	18864-C

8 - PN 18865

WARNING

FALLING OFF CAN RESULT IN BEING RUN OVER.

Tractor must be equipped with ROPS (or ROPS CAB) and seat belt. Keep foldable ROPS systems in “locked up” position at all times.

Buckle Up! Keep seat belt securely fastened.

Allow no riders.

RAISED EQUIPMENT CAN DROP AND CRUSH.

Before working underneath, follow all instructions and safety rules in operator’s manual and securely block up all corners of equipment with jack stands.

Securely blocking prevents equipment dropping from hydraulic leak- down, hydraulic system failures or mechanical component failures.

FALLING OFF OR FAILING TO BLOCK SECURELY CAN RESULT IN SERIOUS INJURY OR DEATH.

WARNING

540RPM!"#$

18866-D

6a - PN 18866

540RPM -OR-

6b - PN 15922

1000 RPM

WARNING

DO NOT EXCEED PTO SPEED OF

1000 RPM

PTO speeds higher than 1000 RPM can cause equipment failure and personal injury.

7 - PN 18877

WARNING

TO AVOID SERIOUS INJURY OR DEATH:

Read Operator's Manual (available from dealer) and follow all safety precautions.

Keep all shields in place and in good condition.

Operate mower from tractor seat only.

Lower mower, stop engine and remove key before dismounting tractor.

Allow no children or untrained persons to operate equipment.

Do not transport towed or semi-mounted units over 20 mph.

FAILURE TO OPERATE SAFELY

CAN RESULT IN

INJURY OR DEATH.

18877-C

9 - PN 15503

DANGER

ROTATING BLADES AND

THROWN OBJECTS

Do not put hands or feet under or into mower when engine is running.

Before mowing, clear area of objects that may be thrown by blade.

Keep bystanders away.

Keep guards in place and in good condition.

BLADE CONTACT OR THROWN OBJECTS CAN CAUSE SERIOUS INJURY OR DEATH.

15503-C

12 Safety	MAN0577 (6/29/2007)

Image 12

Contents

Rotary Cutter Introduction Table of Contents LEA EL InstructivoSpecifications General InformationFree Mower Safety Video Training Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishSafety Rules TrainingPreparation Operation TransportationMaintenance Storage Safety & Instructional Decals Be Careful1000 RPM 33347E Operation Tractor StabilityConnect Cutter to Tractor PULL-TYPE Connect Cutter to Tractor Mounted Driveline Adjustment Mounted Category 2 & 3 Quick HitchesShorten Driveline Cutting Height Adjustment Driveline Interference CheckMounted Units Pull-Type UnitsAttitude Adjustment PULL-TYPE Driveline Adjustment PULL-TYPEWheel Spacing Blade SelectionCutter Operation Mowing TipsTransporting PRE-OPERATION Check List Owners ResponsibilityOwner Service Blocking MethodLubrication Gearbox Lubrication= Jackstand Placement Installing Blades Blade ServicingRemoving Blades Figure Sharpening BladesSlip Clutch Adjustment Repairing Optional Chain ShieldingShielding Repair Flexible Coupler Rubber Disk Replacement Servicing Tires SafelyCleaning After Each UseTroubleshooting Problem Possible Cause SolutionTroubleshooting Dealer Service Gearbox MaintenanceSeal Replacement Seal InstallationHorizontal Shaft Seal Repair Figure Side Gearbox Repair Figure Remove Gearbox from CutterDisassemble Gearbox Assemble GearboxReinstall Gearbox Side Gearbox AssemblyCenter Gearbox Repair Figure HhcsDisassemble Gearbox Figure Assemble Gearbox FigureSide Drive Service CrossbarCrossbar Removal Crossbar Installation Crossbar RemovalJoint Disassembly Crossbar TimingUniversal Joint Repair Joint Assembly Install CupsAssembly Instructions Dealer SET-UP InstructionsTS1680 PULL-TYPE Cutter Rear Half Install SMV Emblem TS1680 Pull-Type Cutter Assembly Rear HalfFront Half Figure Install Tongue Install CV Driveline FigureTS1680 Pull-Type Cutter Assembly Front Half Install A-Frame Install Tailwheel ArmsInstall Hydraulic Hoses TS1680 Mounted Cutter FigureGR5 Install SMV Emblem Semi-Mounted Install Chain Shielding OptionalALL Models Fill Gearboxes Side GearboxesInstall Light KIT Optional Install Stump Jumper OptionalInstall Shredder KIT Optional Shredder Kit InstallationStationary Blade Positions for 1000 RPM and 540 RPM Models Dealer Check Lists PRE-DELIVERY Check ListDelivery Check List Parts Index Main Frame Assembly REF Part PULL-TYPE Assembly Front Half See page 62 -or PULL-TYPE Assembly Rear Half SeeWheel & Tire Assembly REF Part QTY DescriptionMounted Cutter Assembly Tailwheel see Center Gearbox Assembly Assembly TS1680 -or Side Gearbox Assembly 1024795 Complete 540 RPM Gearbox Type a 40 RPM Front CV Drive Assembly Type B 540 RPM Front CV Drive Assembly Type a 1000 RPM Front CV Drive Assembly RPM 1-3/8 21-SplinedRPM 1-3/4 20-Splined Type B 1000 RPM Front CV Drive Assembly Rear FIXED-LENGTH Drive for Constant Velocity Drive Slip Clutch Drive Assembly Mounted Flexible Coupler Spring Wheel ARM Assembly Pull Type Caster ARM Assembly Mounted Caster ARM Assembly Chain Shielding Standard Stump Jumper Assembly Optional Light KIT OptionalShredder KIT Optional 2 x 8 Stroke Hydraulic Cylinder Optional Hydraulic Cylinder Stroke Control KIT Optional Crossbar Puller OptionalBolt Torque Chart SAE Series Torque ChartMetric Series Bolt Size Chart AbbreviationsAssembly IndexWarranty Woods Equipment Company MAN0577