Woods Equipment TS1680Q manual 33347E

Page 13

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

10 - PN 1002940 AMBER FRONT REFLECTOR 9"

11 - PN 57123 RED REAR REFLECTOR 9"

19 - PN 20034034 RED / ORANGE FLUORESCENT 2" X 9"

13 - PN 1004991

12 - PN 1004114

DANGER

If shaft connection is visible, shield is missing. Replace shield before

operating equipment.

1004114

1004991

WARNING

RAISED CUTTER CAN DROP AND CRUSH

Cutters must be equipped with transport lock.

stands.

All transport components must be functional, kept in good

Blocking up prevents cutter dropping from hydraulic leak down, hydraulic system failures, or mechanical component failures.

FAILURE TO FOLLOW INSTRUCTIONS CAN

RESULT IN SERIOUS INJURY OR DEATH.

TRANSPORT LOCK

AND CYLINDER REQUIREMENTS

SINGLE-ACTING FULL

EXTENSION

TRANSPORT

LOCK

14 - PN 19924

	WARNING

	Check for leaks with cardboard; never use hand.
	Before loosening fittings: lower load, release pressure, and
	be sure oil is cool.
19924-B	Consult physician immediately if skin penetration occurs.

15a - PN 57840

540 RPM

-OR-

15b - PN 57841

1000 RPM

17 - PN 15502

WARNING

ROTATING COMPONENTS

Do not operate without cover in place.

Look and listen for rotation. Do not open cover until all components have stopped.

CONTACT WITH ROTATING PARTS

CAN CAUSE SERIOUS INJURY.

15502--B

16 - PN 33347

33347E

18 - PN 24611

SLOW MOVING VEHICLE EMBLEM

MAN0577 (6/29/2007)	Safety 13
MAN0577 (6/29/2007)

Image 13

Contents

Rotary Cutter Introduction LEA EL Instructivo Table of ContentsGeneral Information SpecificationsFree Mower Safety Video Training Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishTraining Safety RulesPreparation Transportation Operation Maintenance Storage Be Careful Safety & Instructional Decals1000 RPM 33347E Tractor Stability OperationConnect Cutter to Tractor PULL-TYPE Connect Cutter to Tractor Mounted Category 2 & 3 Quick Hitches Driveline Adjustment MountedShorten Driveline Driveline Interference Check Cutting Height AdjustmentMounted Units Pull-Type UnitsDriveline Adjustment PULL-TYPE Attitude Adjustment PULL-TYPEWheel Spacing Blade SelectionMowing Tips Cutter OperationTransporting Owners Responsibility PRE-OPERATION Check ListBlocking Method Owner ServiceLubrication Gearbox Lubrication= Jackstand Placement Blade Servicing Installing BladesRemoving Blades Figure Sharpening BladesRepairing Optional Chain Shielding Slip Clutch AdjustmentShielding Repair Servicing Tires Safely Flexible Coupler Rubber Disk ReplacementAfter Each Use CleaningProblem Possible Cause Solution TroubleshootingTroubleshooting Gearbox Maintenance Dealer ServiceSeal Replacement Seal InstallationSide Gearbox Repair Figure Remove Gearbox from Cutter Horizontal Shaft Seal Repair FigureDisassemble Gearbox Assemble GearboxSide Gearbox Assembly Reinstall GearboxHhcs Center Gearbox Repair FigureAssemble Gearbox Figure Disassemble Gearbox FigureCrossbar Side Drive ServiceCrossbar Removal Crossbar Removal Crossbar InstallationCrossbar Timing Joint DisassemblyUniversal Joint Repair Install Cups Joint AssemblyDealer SET-UP Instructions Assembly InstructionsTS1680 PULL-TYPE Cutter Rear Half TS1680 Pull-Type Cutter Assembly Rear Half Install SMV EmblemInstall CV Driveline Figure Front Half Figure Install TongueTS1680 Pull-Type Cutter Assembly Front Half Install Tailwheel Arms Install A-FrameInstall Hydraulic Hoses TS1680 Mounted Cutter FigureGR5 Install Chain Shielding Optional Install SMV Emblem Semi-MountedALL Models Fill Gearboxes Side GearboxesInstall Stump Jumper Optional Install Light KIT OptionalShredder Kit Installation Install Shredder KIT OptionalStationary Blade Positions for 1000 RPM and 540 RPM Models PRE-DELIVERY Check List Dealer Check ListsDelivery Check List Parts Index Main Frame Assembly REF Part PULL-TYPE Assembly Front Half See page 62 -or See PULL-TYPE Assembly Rear HalfREF Part QTY Description Wheel & Tire AssemblyMounted Cutter Assembly Tailwheel see Center Gearbox Assembly Assembly TS1680 -or Side Gearbox Assembly 1024795 Complete 540 RPM Gearbox Type a 40 RPM Front CV Drive Assembly Type B 540 RPM Front CV Drive Assembly RPM 1-3/8 21-Splined Type a 1000 RPM Front CV Drive AssemblyRPM 1-3/4 20-Splined Type B 1000 RPM Front CV Drive Assembly Rear FIXED-LENGTH Drive for Constant Velocity Drive Slip Clutch Drive Assembly Mounted Flexible Coupler Spring Wheel ARM Assembly Pull Type Caster ARM Assembly Mounted Caster ARM Assembly Chain Shielding Standard Light KIT Optional Stump Jumper Assembly OptionalShredder KIT Optional 2 x 8 Stroke Hydraulic Cylinder Optional Crossbar Puller Optional Hydraulic Cylinder Stroke Control KIT OptionalSAE Series Torque Chart Bolt Torque ChartMetric Series Abbreviations Bolt Size ChartIndex AssemblyWarranty Woods Equipment Company MAN0577