Woods Equipment TS1680Q manual Reinstall Gearbox, Side Gearbox Assembly

Page 31

10.Secure snap ring (5) on input shaft (4) if not already secure.

11.Place gear (1a or 1b) through top of housing and align gear (1a or 1b) and gear (1a or 17) so that gear teeth are a match.

12.While holding gear (1a or 1b) in place, slide input shaft (4) through gear (1a or 1b) and bearing (2). Align splines on shaft (4) and gear (1a or 1b). Slide spacer (18) over input shaft (4) and press bearing

(2)onto input shaft (4), using a round tube of the correct diameter and a hand press.

13.Slide shim (6) over input shaft (4) and secure with snap ring (5).

14.Check input shaft end float by moving the input shaft (4) by hand. If end float is higher than 0.012", insert shim between input shaft (4) and rear bearing (2). Repeat until end float is less than 0.012". Check rotational torque by hand. The torque should be less than 2.2 lbs-inch.

15.Check that the gear backlash is between 0.006" and 0.016". You should not have to adjust the backlash.

16.Press in input oil seal (3), using tube of correct diameter. Be careful not to damage seal lip.

17.Press oil cap (16) on to cover the rear of housing, using a tube of the correct diameter.

18.Place top cover (20) on top of housing and secure with six cap screws (21).

19.Check gearbox housing for leaks by plugging all holes except one. Apply 4 psi compressed air and immerse the gearbox in water to verify that there are no leaks.

20.Remove gearbox from water and dry off with compressed air. Add SAE 80W or 90W EP oil until it runs out of side level hole. Tighten all plugs.

Reinstall Gearbox

NOTE: Gearbox is heavy: do not attempt to move without mechanical assistance.

1.Set gearbox on cutter and fasten with bolts and nuts. Torque bolts to 300 lbs-ft.

2.Attach crossbar (Crossbar Installation, page 35).

1a. Crown gear, 21T (TS1680)

1b. Crown gear, 22T (TS1680Q)

2.Input bearing

3.Oil seal (Horizontal shaft)

4.Input shaft

5.Snap ring

6.Shim, 70.3 x 84.7

7.Snap ring, 50 x 47 x 2

8.Castle nut, M40 x 1.5

9.Shim, 50.3 x 70.3

10.Bearing, cup & cone

11.Protective seal

12.Oil seal (Vertical Shaft)

13.Bearing, cup & cone

14.Output shaft

15.Cotter pin

16.Cap

17.Gear pinion (TS1680Q)

18.Shim, 45.3 x 2.5

19.Shim, 40.3 x61.7

20.Top cover

21.Cap screw 8mm x 25 (8.8)

22.3/8 NPT Solid plug

23.Castle nut

24.Cotter pin, 1/4 x 2-1/4

Figure 14. Side Gearbox Assembly

MAN0577 (6/29/2007)

Dealer Service 31

 

 

Image 31
Contents Rotary Cutter Introduction LEA EL Instructivo Table of ContentsGeneral Information SpecificationsFree Mower Safety Video Training Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishTraining Safety RulesPreparation Transportation OperationMaintenance Storage Be Careful Safety & Instructional Decals1000 RPM 33347E Tractor Stability OperationConnect Cutter to Tractor PULL-TYPE Connect Cutter to Tractor Mounted Category 2 & 3 Quick Hitches Driveline Adjustment MountedShorten Driveline Pull-Type Units Cutting Height AdjustmentDriveline Interference Check Mounted UnitsBlade Selection Attitude Adjustment PULL-TYPEDriveline Adjustment PULL-TYPE Wheel SpacingMowing Tips Cutter OperationTransporting Owners Responsibility PRE-OPERATION Check ListGearbox Lubrication Owner ServiceBlocking Method Lubrication= Jackstand Placement Sharpening Blades Installing BladesBlade Servicing Removing Blades FigureRepairing Optional Chain Shielding Slip Clutch AdjustmentShielding Repair Servicing Tires Safely Flexible Coupler Rubber Disk ReplacementAfter Each Use CleaningProblem Possible Cause Solution TroubleshootingTroubleshooting Seal Installation Dealer ServiceGearbox Maintenance Seal ReplacementAssemble Gearbox Horizontal Shaft Seal Repair FigureSide Gearbox Repair Figure Remove Gearbox from Cutter Disassemble GearboxSide Gearbox Assembly Reinstall GearboxHhcs Center Gearbox Repair FigureAssemble Gearbox Figure Disassemble Gearbox FigureCrossbar Side Drive ServiceCrossbar Removal Crossbar Removal Crossbar InstallationCrossbar Timing Joint DisassemblyUniversal Joint Repair Install Cups Joint AssemblyDealer SET-UP Instructions Assembly InstructionsTS1680 PULL-TYPE Cutter Rear Half TS1680 Pull-Type Cutter Assembly Rear Half Install SMV EmblemInstall CV Driveline Figure Front Half Figure Install TongueTS1680 Pull-Type Cutter Assembly Front Half TS1680 Mounted Cutter Figure Install A-FrameInstall Tailwheel Arms Install Hydraulic HosesGR5 Side Gearboxes Install SMV Emblem Semi-MountedInstall Chain Shielding Optional ALL Models Fill GearboxesInstall Stump Jumper Optional Install Light KIT OptionalShredder Kit Installation Install Shredder KIT OptionalStationary Blade Positions for 1000 RPM and 540 RPM Models PRE-DELIVERY Check List Dealer Check ListsDelivery Check List Parts Index Main Frame Assembly REF Part PULL-TYPE Assembly Front Half See page 62 -or See PULL-TYPE Assembly Rear HalfREF Part QTY Description Wheel & Tire AssemblyMounted Cutter Assembly Tailwheel see Center Gearbox Assembly Assembly TS1680 -or Side Gearbox Assembly 1024795 Complete 540 RPM Gearbox Type a 40 RPM Front CV Drive Assembly Type B 540 RPM Front CV Drive Assembly RPM 1-3/8 21-Splined Type a 1000 RPM Front CV Drive AssemblyRPM 1-3/4 20-Splined Type B 1000 RPM Front CV Drive Assembly Rear FIXED-LENGTH Drive for Constant Velocity Drive Slip Clutch Drive Assembly Mounted Flexible Coupler Spring Wheel ARM Assembly Pull Type Caster ARM Assembly Mounted Caster ARM Assembly Chain Shielding Standard Light KIT Optional Stump Jumper Assembly OptionalShredder KIT Optional 2 x 8 Stroke Hydraulic Cylinder Optional Crossbar Puller Optional Hydraulic Cylinder Stroke Control KIT OptionalSAE Series Torque Chart Bolt Torque ChartMetric Series Abbreviations Bolt Size ChartIndex AssemblyWarranty Woods Equipment Company MAN0577

TS1680, TS1680Q specifications

Woods Equipment has long been a prominent name in the agricultural and landscaping sectors, and its TS1680Q and TS1680 models further cement this reputation. Designed for versatility and reliability, both models shine in various applications, ranging from mowing to maintaining landscapes.

One of the standout features of the Woods TS1680Q and TS1680 is their robust build quality. Crafted with heavy-duty materials, these models are engineered to withstand the rigors of tough terrain and demanding workloads. The TS1680Q, being the quieter variant, employs advanced sound-dampening technologies, ensuring that operators can work without the disruptive noise typical of many competitors.

With a cutting width of 68 inches, both models are designed for efficiency. The wide cutting deck not only allows operators to cover more ground quickly but also ensures a clean and even cut on various grass types. The TS1680Q further enhances mowing precision with its unique floating deck design. This feature enables the cutting deck to follow ground contours, reducing scalping on uneven surfaces.

Another notable characteristic is the versatility of attachment options. Both models come equipped with a category 1 three-point hitch which allows for easy attachment of numerous implements. This adaptability means operators can use the TS1680Q and TS1680 for other tasks, such as tilling or hauling, making it a multi-functional powerhouse for any farm or landscape project.

The hydraulic system on these models is engineered for high performance. With user-friendly controls and responsive feedback, operators can adjust settings with ease. Combined with a powerful engine, the TS1680Q and TS1680 offer reliable performance and energy efficiency, contributing to reduced fuel expenditure in the long run.

Safety features are also a priority, with shields and guards designed to protect operators during use. The controls are ergonomically situated to minimize potential hazards. Additionally, the low center of gravity design ensures stable operation, reducing the risk of tipping especially while working on inclines.

In conclusion, the Woods Equipment TS1680Q and TS1680 models are designed with the modern user in mind. Their blend of durability, innovative technology, and operational versatility makes them a top choice for both agricultural use and landscaping projects. Whether you're a farmer looking for reliable mowing solutions or a landscaper in need of a versatile implement, these models deliver exceptional performance and value.