Front Half Figure Install Tongue | Woods Equipment TS1680Q manual

TS1680 Pull-Type Assembly (Continued)

FRONT HALF (Figure 29)

Install Tongue

1.Place tongue (1) between mast plates.

2.Place washer (27) and sleeve (19) on cap screw (26).

3.Place washer (27†) between mast plates and tongue, insert cap screw (26) with washer (27†) and sleeve (19) through mast plates, tongue and washer (27†).

4.Secure with washer (27) and lock nut (28).

5.Attach front half of attitude rod (13) to lug on tongue using clevis pin (18) and cotter pin (29).

6.Raise front of cutter and install parking jack (4) to support tongue.

7.Attach safety tow chain (5) to tongue by wrapping chain around diagonal brace and threading the hook end back through the large link on opposite end of chain.

Install CV Driveline (Figure 29)

Install Driveline

3.Attach rear tether chain on driveline to clip on plastic gearbox shield.

H-Frame

1.Attach H-frame mounting bracket (2) to cutter deck with carriage bolts (34), washers (35) and lock nuts (30). Attach front of bracket (2) to cutter frame with washers (36), lock washers (32) and self-tapping screws (37).

2.Place H-frame (3) over bracket and align holes.

3.Secure H-frame to bracket using cap screw (24), two sleeves (16), two cup washers (17) and lock nut (25).

Attach Driveline to H-Frame

NOTE: Select holes in H-frame that will allow driveline to run level. Refer to Operation section for driveline height. Final adjustment will be necessary when cutter is attached to the tractor.

Place driveline carrier bearing (8) between H-frame (3) and secure with clevis pin (12) and cotter pin (38).

Install CV Drive

1.Slide rear yoke of CV driveline (6) over shaft of driveline (7) and align with notch on shaft.

2.Secure drives together using cap screw (22) and lock nut (21).

Install Drive Shield & Hose Holder

1.Coat input shaft of gearbox with a light coating of grease.

2.Attach slip clutch on driveline (7) to input shaft of gearbox. Tighten cap screws (20) and lock nuts (21).

1.Attach drive shield (11) to driveline carrier bearing using two cap screws (33) and lock washers (32).

2.Attach hydraulic hose holder (15) to the top hole in H-frame (3) with cap screw (23), spacer (14) and lock nut (30).

1.	Tongue	21.	1/2 NC Lock nut
2.	CV H-frame mounting base	22.	1/2 NC x 2 HHCS GR5
3.	H-Frame	23.	1/2 NC x 5-1/2 HHCS GR5
4.	Parking jack	24.	5/8 NC x 6 HHCS GR5
5.	Safety chain	25.	5/8 NC Lock nut
6.	Front 2/3 drive	26.	1 NC x 9 HHCS GR5
7.	Rear 1/3 drive	27.	1" Standard flat washer
8.	3-Joint drive bearing housing	28.	1 NC Lock nut
11.	Shield	29.	1/4 x 1-1/2 Cotter pin
12.	Clevis pin, 1/2 x 5-3/4	30.	1/2 NC Flange lock nut
13.	Attitude rod	32.	3/8 Standard lock washer
14.	1/2 Schedule 40 x 3.56 pipe	33.	3/8 NC x 1 HHCS
15.	Hose holder	34.	1/2 NC x 1-1/2 Carriage bolt GR5
16.	Sleeve, 5/8 x 1 x 9/16	35.	1/2 Flat washer
17.	Cup washer	36.	3/8 Flat washer
18.	Clevis pin, 1 x 2-1/2	37.	3/8 x 1-1/4 Self-tapping screw
19.	Sleeve, 1.02 x 1.38 x .62	38.	3/16 x 1 Cotter pin
20.	1/2 NC x 3 HHCS GR5	+	As required

40Assembly

(Rev. 1/25/2008) MAN0577 (6/29/2007)

TS1680, TS1680Q specifications

Woods Equipment has long been a prominent name in the agricultural and landscaping sectors, and its TS1680Q and TS1680 models further cement this reputation. Designed for versatility and reliability, both models shine in various applications, ranging from mowing to maintaining landscapes.

One of the standout features of the Woods TS1680Q and TS1680 is their robust build quality. Crafted with heavy-duty materials, these models are engineered to withstand the rigors of tough terrain and demanding workloads. The TS1680Q, being the quieter variant, employs advanced sound-dampening technologies, ensuring that operators can work without the disruptive noise typical of many competitors.

With a cutting width of 68 inches, both models are designed for efficiency. The wide cutting deck not only allows operators to cover more ground quickly but also ensures a clean and even cut on various grass types. The TS1680Q further enhances mowing precision with its unique floating deck design. This feature enables the cutting deck to follow ground contours, reducing scalping on uneven surfaces.

Another notable characteristic is the versatility of attachment options. Both models come equipped with a category 1 three-point hitch which allows for easy attachment of numerous implements. This adaptability means operators can use the TS1680Q and TS1680 for other tasks, such as tilling or hauling, making it a multi-functional powerhouse for any farm or landscape project.

The hydraulic system on these models is engineered for high performance. With user-friendly controls and responsive feedback, operators can adjust settings with ease. Combined with a powerful engine, the TS1680Q and TS1680 offer reliable performance and energy efficiency, contributing to reduced fuel expenditure in the long run.

Safety features are also a priority, with shields and guards designed to protect operators during use. The controls are ergonomically situated to minimize potential hazards. Additionally, the low center of gravity design ensures stable operation, reducing the risk of tipping especially while working on inclines.

In conclusion, the Woods Equipment TS1680Q and TS1680 models are designed with the modern user in mind. Their blend of durability, innovative technology, and operational versatility makes them a top choice for both agricultural use and landscaping projects. Whether you're a farmer looking for reliable mowing solutions or a landscaper in need of a versatile implement, these models deliver exceptional performance and value.