Woods Equipment TS1680Q manual Install SMV Emblem Semi-Mounted, ALL Models Fill Gearboxes

Page 44

Install SMV Emblem (Semi-Mounted)

See Figure 30.

1.Attach SMV socket (35) to deck bracket with two carriage bolts (38) and lock nuts (39).

2.Attach SMV emblem (37) to SMV bracket (36) using two round head cap screws (40) and hex nuts (41).

3.Insert SMV bracket (36) and emblem (37) into socket (35).

ALL MODELS

FILL GEARBOXES

NOTICE

Gearbox is not filled at the factory. Prior to delivery to customer, make sure gearbox is filled only half-full with 80W or 90W API GL-4 or GL-5 gear lube. Use side plug to remove any excess oil.

Side Gearboxes

1.Make sure vent plug hole is clear (installed by dealer).

2.Remove plug on side of gearbox

3.Fill gearbox until oil runs out the side plug on gearbox. Use a high quality gear oil with a viscosity index of 80W or 90W and an API service rating of GL-4 or GL-5.

4.Install side plug and vent plug.

Center Gearbox

1.Make sure dipstick vent hole is clear.

2.Fill gearbox until oil level is between rings with dipstick seated. Use a high quality gear oil with a viscosity index of 80W or 90W and an API service rating of GL-4 or GL-5.

3.Install dipstick.

INSTALL CHAIN SHIELDING (OPTIONAL)

Full chain shielding must be installed when operating in populated areas or other areas where thrown objects could injure people or damage property.

If this machine is not equipped with full chain shielding, operation must be stopped when any- one comes within 300 feet (92 m).

This shielding is designed to reduce the risk of thrown objects. The mower deck and protec- tive devices cannot prevent all objects from escaping the blade enclosure in every mowing condition. It is possible for objects to ricochet and escape, traveling as much as 300 feet (92 m).

Full chain shielding is required for all non-agri- cultural mowing. Full shielding is also recom- mended for all agricultural use to further reduce the risk of thrown objects.

The chain shield assemblies are ready for installation when you receive them.

Install front and rear chain shielding as shown using carriage bolts (9) and lock nuts (10).

9. 3/8 NC x 1-1/4 Carriage bolt

10. 3/8 NC Flange lock nut

Figure 31. TS1680 Chain Shielding Installation

44 Assembly

MAN0577 (6/29/2007)

 

 

Image 44
Contents Rotary Cutter Introduction Table of Contents LEA EL InstructivoSpecifications General InformationFree Mower Safety Video Training Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishPreparation Safety RulesTraining Operation TransportationMaintenance Storage Safety & Instructional Decals Be Careful1000 RPM 33347E Connect Cutter to Tractor PULL-TYPE OperationTractor Stability Connect Cutter to Tractor Mounted Shorten Driveline Driveline Adjustment MountedCategory 2 & 3 Quick Hitches Cutting Height Adjustment Driveline Interference CheckMounted Units Pull-Type UnitsAttitude Adjustment PULL-TYPE Driveline Adjustment PULL-TYPEWheel Spacing Blade SelectionTransporting Cutter OperationMowing Tips PRE-OPERATION Check List Owners ResponsibilityOwner Service Blocking MethodLubrication Gearbox Lubrication= Jackstand Placement Installing Blades Blade ServicingRemoving Blades Figure Sharpening BladesShielding Repair Slip Clutch AdjustmentRepairing Optional Chain Shielding Flexible Coupler Rubber Disk Replacement Servicing Tires SafelyCleaning After Each UseTroubleshooting Problem Possible Cause SolutionTroubleshooting Dealer Service Gearbox MaintenanceSeal Replacement Seal InstallationHorizontal Shaft Seal Repair Figure Side Gearbox Repair Figure Remove Gearbox from CutterDisassemble Gearbox Assemble GearboxReinstall Gearbox Side Gearbox AssemblyCenter Gearbox Repair Figure HhcsDisassemble Gearbox Figure Assemble Gearbox FigureCrossbar Removal Side Drive ServiceCrossbar Crossbar Installation Crossbar RemovalUniversal Joint Repair Joint DisassemblyCrossbar Timing Joint Assembly Install CupsTS1680 PULL-TYPE Cutter Rear Half Assembly InstructionsDealer SET-UP Instructions Install SMV Emblem TS1680 Pull-Type Cutter Assembly Rear HalfFront Half Figure Install Tongue Install CV Driveline FigureTS1680 Pull-Type Cutter Assembly Front Half Install A-Frame Install Tailwheel ArmsInstall Hydraulic Hoses TS1680 Mounted Cutter FigureGR5 Install SMV Emblem Semi-Mounted Install Chain Shielding OptionalALL Models Fill Gearboxes Side GearboxesInstall Light KIT Optional Install Stump Jumper OptionalInstall Shredder KIT Optional Shredder Kit InstallationStationary Blade Positions for 1000 RPM and 540 RPM Models Delivery Check List Dealer Check ListsPRE-DELIVERY Check List Parts Index Main Frame Assembly REF Part PULL-TYPE Assembly Front Half See page 62 -or PULL-TYPE Assembly Rear Half SeeWheel & Tire Assembly REF Part QTY DescriptionMounted Cutter Assembly Tailwheel see Center Gearbox Assembly Assembly TS1680 -or Side Gearbox Assembly 1024795 Complete 540 RPM Gearbox Type a 40 RPM Front CV Drive Assembly Type B 540 RPM Front CV Drive Assembly RPM 1-3/4 20-Splined Type a 1000 RPM Front CV Drive AssemblyRPM 1-3/8 21-Splined Type B 1000 RPM Front CV Drive Assembly Rear FIXED-LENGTH Drive for Constant Velocity Drive Slip Clutch Drive Assembly Mounted Flexible Coupler Spring Wheel ARM Assembly Pull Type Caster ARM Assembly Mounted Caster ARM Assembly Chain Shielding Standard Stump Jumper Assembly Optional Light KIT OptionalShredder KIT Optional 2 x 8 Stroke Hydraulic Cylinder Optional Hydraulic Cylinder Stroke Control KIT Optional Crossbar Puller OptionalMetric Series Bolt Torque ChartSAE Series Torque Chart Bolt Size Chart AbbreviationsAssembly IndexWarranty Woods Equipment Company MAN0577

TS1680, TS1680Q specifications

Woods Equipment has long been a prominent name in the agricultural and landscaping sectors, and its TS1680Q and TS1680 models further cement this reputation. Designed for versatility and reliability, both models shine in various applications, ranging from mowing to maintaining landscapes.

One of the standout features of the Woods TS1680Q and TS1680 is their robust build quality. Crafted with heavy-duty materials, these models are engineered to withstand the rigors of tough terrain and demanding workloads. The TS1680Q, being the quieter variant, employs advanced sound-dampening technologies, ensuring that operators can work without the disruptive noise typical of many competitors.

With a cutting width of 68 inches, both models are designed for efficiency. The wide cutting deck not only allows operators to cover more ground quickly but also ensures a clean and even cut on various grass types. The TS1680Q further enhances mowing precision with its unique floating deck design. This feature enables the cutting deck to follow ground contours, reducing scalping on uneven surfaces.

Another notable characteristic is the versatility of attachment options. Both models come equipped with a category 1 three-point hitch which allows for easy attachment of numerous implements. This adaptability means operators can use the TS1680Q and TS1680 for other tasks, such as tilling or hauling, making it a multi-functional powerhouse for any farm or landscape project.

The hydraulic system on these models is engineered for high performance. With user-friendly controls and responsive feedback, operators can adjust settings with ease. Combined with a powerful engine, the TS1680Q and TS1680 offer reliable performance and energy efficiency, contributing to reduced fuel expenditure in the long run.

Safety features are also a priority, with shields and guards designed to protect operators during use. The controls are ergonomically situated to minimize potential hazards. Additionally, the low center of gravity design ensures stable operation, reducing the risk of tipping especially while working on inclines.

In conclusion, the Woods Equipment TS1680Q and TS1680 models are designed with the modern user in mind. Their blend of durability, innovative technology, and operational versatility makes them a top choice for both agricultural use and landscaping projects. Whether you're a farmer looking for reliable mowing solutions or a landscaper in need of a versatile implement, these models deliver exceptional performance and value.